Q.2) The windlass is supported by a thrust bearing at A and a smooth journal bearing at B, which are properly aligned on the shaft. Determine the magnitude of the vertical force P that must be applied to the handle to maintain the equilibrium of the 100kg bucket. Also, calculate the reactions at the bearings. Since the bearings at A and B are aligned correctly, only force reactions occur at these supports. 0.3 m 0.1 m 981 N 0.5 m 0.4 m B V 30% 0.3 cos 30°m X 0.3 m 0.5 m 0.1 m 0.1 m X 0.3 m 100 kg 0.3 m

Q.2) The windlass is supported by a thrust bearing at A and a smooth journal bearing at B, which are properly aligned on the shaft. Determine the magnitude of the vertical force P that must be applied to the handle to maintain the equilibrium of the 100kg bucket. Also, calculate the reactions at the bearings. Since the bearings at A and B are aligned correctly, only force reactions occur at these supports. 0.3 m 0.1 m 981 N 0.5 m 0.4 m B V 30% 0.3 cos 30°m X 0.3 m 0.5 m 0.1 m 0.1 m X 0.3 m 100 kg 0.3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. The members of a truss are connected to the gusset plate. If the forces are concurrent at point O, determine the magnitudes of F and T for equilibrium. Take 0 = 30°. 4. The gusset plate is subjected to the forces of four members. Determine the force in member B and its proper orientation 0 for equilibrium. The forces are concurrent at point O. Take F 12kN. 8 kN 45 B. 5 kN F Problems 3 and 4
Determine the magnitude of the pin force at A.Assume W = 665 lb, a = 3.7 ft, b = 2.9 ft, r = 8 in.
The bobcat loader (Figure Q3) has a mass of 1200-kg, shows the center of mass is at G1. If there is a 200-kg pebble in the bucket, with center of mass at G2 determine the reactions of each pair of wheels A and B on the ground and the force in the hydraulic cylinder CD and at the pin E. There is a similar linkage on each side of the loader. L0.5 m E 0.1 m_ D 0.2 m G2 0.18 m G1 0.6 m 0.5 m В 0.45 m 1.2 m 0.15 m 0.2 m 0.05 m Figure Q3
The mass center G of the 1365-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions. Answers: 1329 mm-997 mm Normal force under each of the front tires: N₁= Normal force under each of the rear tires: N₁ = i N N
The mass center G of the 1350-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions. -1338 mm-967 mm-
The mass center G of the 1540-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions. Answers: GO 1283 mm-871 mm Normal force under each of the front tires: Nf= Normal force under each of the rear tires: N₁ = i 3054 i 4499 ! N N
If P=9.8kN Determine the reaction forces at Supports A and D
45 lb 4=0.40 4 = 0.30 Determine whether the block shown is in equilibrium and find the magnitude and direction of the friction force when P= 100 lb. 40
The cylinder shown weighs 2500 kg, calculate the reactions on the smooth surfaces A and B. Given: θ1 = 35° and θ2 =78°. SOLVE THE FF: Reaction at A (Answer: 26.061 kn) Reaction at B (Answer: 15.282 kn)
A force of P=180lb supports a 300lb box in an inclined plane as shown. Determine the angle at which it must be inclined with the smooth plane to hold the box in equilibrium.
The unstretched length of spring AB is 1 m. If the block is held in the equilibrium position shown, what would be the weight of the block at D? Hint: Find the stretched length of spring AB and use the equilibrium. -3 m- -4 m- www kAB = 30 3 m kAC = 20 N/m %3D %3D A
The 10 Ib weight is supported by the cord AC, a roller and by a spring. If the spring has an unstretched length of 8 in. and the weight is in equilibrium when d = 4 in., determine the stiffness k of the spring. 12 in. in A Select one: O a.k= 4.8 lb/in Ob.k=7.8 Ib/in Oc.k=6.8 Ib/in Od.k=5.8 Ib/in