The figure (Fig. 1) below is a differential amplifier used to measure the voltage differentia between amplifier A1 and A2. If the range of variation is from -10 mV to +10 mV and R13 R2= 2R4 = 3R6 = 100 kQ and R3 = twice the value of R5, choose RG so that the corresponding range of the output voltage is from -5 V to +5 V. . Use E24 standard values for all externa resistors, capacitors, and inductors. Also Use VD = VBE = 0.7VM (Ctrl) m1+ Vem o VB R3 R5 A1 VB' R1 Fig. 1 RG R2 o Output АЗ R4 VA' A2 VA m2+ Vem o R6

The figure (Fig. 1) below is a differential amplifier used to measure the voltage differentia between amplifier A1 and A2. If the range of variation is from -10 mV to +10 mV and R13 R2= 2R4 = 3R6 = 100 kQ and R3 = twice the value of R5, choose RG so that the corresponding range of the output voltage is from -5 V to +5 V. . Use E24 standard values for all externa resistors, capacitors, and inductors. Also Use VD = VBE = 0.7VM (Ctrl) m1+ Vem o VB R3 R5 A1 VB' R1 Fig. 1 RG R2 o Output АЗ R4 VA' A2 VA m2+ Vem o R6

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Voltage when applied at 2 inputs of Op-amp to get 0 V of output is called_voltage. O a. Output offset O b. Input offset O. All of these O d. In-out offset
O cathode O focusing anode The of an instrument is a measure of how close the output reading of the instrument is to the correct value. In OP-AMP, signal applied to the inverting input gets amplified and obtained as the inverted signal at the output. dows
II- 1) Draw the circuit of a V-l converter and derive an expression for the output current in terms of input voltage. 2) Draw the neat diagram of analog multiplier using log-antilog amplifiers and explain its operation.
In the voltage regulator circuit shown in the figure, the op-amp is ideal. The BJT has VBE=0.7 V and Beta = 100, and the Zener voltage is 4.7 V. For a regulated output of 9 V, the value of R (in Ohms) is Express answers in two decimal points. Show solution on your answer sheet. V = 12 V Vo = 12 V 1 k2 1 k2 AV2 = 47 V %3D ww
2) Draw the small signal model for the amplifier shown below. Do not make any approximations. Label Vin and Vo. Vdd Vdd Vdd R2 R4 R6 R1 Vo1 Vin2 Vo Vin R5 R3 R7
4. Determine the voltage gain of the non-inverting op-amp with Rf-100k and R1=4.7k02. Calculate the output voltage if the input voltage is 200mV
Determine the R2value for the summing amplifier given below so that the output voltage is – 3V. R 4K 2 V 12K b-Vcc
P8. What is the circuit shown below? Explain in details how it works. What are the advantages and disadvantages of using this circuit? Under what conditions this circuit can be turned into an analog amplifier and why? Q5 Transmission Gate 1a Transmission C, Q Vin Gate Q2 Vout Q3 P2a Q4
What output voltage results in the circuit below for an input of 0.5 V. Refer to the following for the values of Rf = 413981 ohms, R1 = 16788 ohms. Express your answer up to two decimal places. ... V. 360 kQ 12 ko Round your answer to 2 decimal places.
Vin -100m/100mV. 10kHz RI B10k RF 100k Vcc +12V U1 UA741 A RL 25k -12V Vee 1. What are the basic features of an OP-AMP? (6) 2. Basic op-amp connections include what? (10) 3. Simulate the circuit using Circuit maker and explain the different between A and B.
2) A differential amplifier has an output voltage given by Vo=9V1-10V2. The two inputs are V1=10mV and V2=20mV. Determine common mode input voltage, common mode gain and the differential gain.
5. If you have this relationship between the input and output voltage Vou=1.5 Vin+2 in which 2 is a bias. Design a circuit that will remove the bias and make the relationship between the input and output as Vou=1.5 Vin. We have a dual supply of ± 12 V available and we need to drive a 10 kQ load. Test your designs under different input voltages and verify that your output voltages are within + 5% of the calculated ones. Simulate the circuit in Multisim and then implement it practically. Prepare a full report about the experiment.