The 58-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the temperature is T₁ = 20°C. (Figure 1) Figure 100 mm 1 of 1 150 mm Part A If the 304-stainless-steel carriage bolts of the clamp each have a diameter of 9 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the force in the cylinder when the temperature rises to T₂ = 130°C. Express your answer to three significant figures and include the appropriate units. F = Submit uА Value Provide Feedback Request Answer Units ? Nex

The 58-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the temperature is T₁ = 20°C. (Figure 1) Figure 100 mm 1 of 1 150 mm Part A If the 304-stainless-steel carriage bolts of the clamp each have a diameter of 9 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the force in the cylinder when the temperature rises to T₂ = 130°C. Express your answer to three significant figures and include the appropriate units. F = Submit uА Value Provide Feedback Request Answer Units ? Nex

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bolt AB in (Figure 1) has a diameter of 18 mm and passes through a sleeve that has an inner diameter of 42 mm and an outer diameter of 52 mm. The bolt and sleeve are made of A-36 steel and are secured to the rigid brackets as shown. If the bolt length is 220 mm and the sleeve length is 200 mm, determine the tension in the bolt when a force of 50 kN is applied to the brackets.
V-links "Im crank arm раper rolling machine forks rod off-loading station air cylinder fork lift truck Determine the critical load on the air-cylinder rod if the crank arm that it rotates is 0.3 m long and in the position with the largest compression of the rod its length equals 0.5 m. The 40-mm-dia rod is solid steelwith a yield strength of 400 MPa. Assume the rod is a fixed-pinned column. Use a theoretical value for the effective length factor. Express your answer to three significant figures and include the appropriate units. HA Per = 1026 kN
The two steel shafts (1) and (2) each Ø10 should be connected to each other with the help of the sleeve (3) (Øinner = 10, Øoutside = 15) also made of steel and two rivets at the points shown. The shaft (1) is firmly clamped on the left- hand side, the force F = 100 N acts on shaft 2 in the direction of the arrow. How are the brass round rivets to be dimensioned so that a safety of the coupling against failure of S = 10 is achieved? hole for rivets 1 F 3 a) What type of connection does a riveted connection have? b) What type of load does the rivet have? c) What is the diameter of the rivets? d) Which areas of the rivet are loaded? (Draw in figure and formula) e) Dimension the rivet
The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T = 15° C. (Figure 1) Part A If the two 304-stainless-steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the temperature at which the average normal stress in either the magnesium or the steel first becomes 14.5 MPa Express your answer to three significant figures and include the appropriate units. HA ? Value degC T = Submit Request Answer Provide Feedback Next > Figure 100 mm 150 mm
For the same question, the M25 Screw will be used when pressing the Nut Wheel onto the shaft. Assuming that the force that the nut needs to suppress is Fçak=1218 kgf (it was found in the previous question, but we don't use it), what should the minimum NUT HEIGHT be in mm to create this force safely? (Screw and Nut's surface safety pressure Pem=45 N/mm2 Screw base diameter d1= 21.5 mm. (Calculate the pitch (h=?) according to the given ones, considering that metric screw is used!)
A hand compactor is composed of a strong rigid arm ABC pinned at B and pin connected link CD. It is designed such that link CD will fail if the compactor is overloaded since CD is easily replaceable. The design is such that when portion AB is horizontal at the bottom of its stroke then theta = 45 degrees. If link CD is 4 mm diameter A36 mild steel determine the largest compaction force that can be developed and the hand force P required with a 1.5 Factor of Safety.
The rigid bar of negligible weight is supported as shown. The middle helical spring is made of 22 mm diameter steel spring and has an outside diameter of 100 mm with 10 turns and the two side springs are made of 32 mm steel spring and has an outside diameter of 250 mm with 8 turns. Before the load P is applied, the side springs are 25 mm longer than the middle spring. If the applied load P = 15 kN and the rigid bar remains horizontal, determine the stress in each spring. Use G = 83 GPa for steel and G = 42 GPa for bronze.
8-23. The plug has a diameter of 30 mm and fits within a rigid sleeve having an inner diameter of 32 mm. Both the plug and the sleeve are 50 mm long. Determine the axial pressure p that must be applied to the top of the plug to cause it to contact the sides of the sleeve. Alsa, how far must the plug be compressed downward in order to do this? The plug is made from a material for which E-5 MPa, v -0.45.
A leafs spring contains 4 full-length and 8 graduated leafs. The eyebolts at the support are 20 inches apart and the system should carry a load of 400 lbs. If the thickness of the available bronze plate is 1“ and Sy = 80 ksi, what leaf width is required at FOS = 8?
Required information Rod BD is made of steel (E-29 106 psi) and is used to brace the axially compressed member ABC. The maximum force that can be developed in member BD is 0.018P. If the stress in BD must not exceed 36 ksi and the maximum change in length of BD must not exceed 0.0002 times the length of ABC, determine the allowable diameter rod that can be used for member BD. Take P - 110 kips. 72 in 54 in If stress in member BD should not exceed 36 (ksi), then the diameter of rod BD d 0.0288 (in) 2
Downvote for incorrect answer The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (b)allow 2 ksi, and the allowable tensile stress within the bolt shank S is (allow 18 ksi, determine the maximum = allowable tension in the bolt shank. The bolt shank has a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.
Determine the n- and t-components of the force F which is exerted by the rod AB on the crank OA. Evaluate your general expression for F = 84 N and (a) e = 30°, B = 25° and (b) e = 16°, B = 27° %3D F BI B L--n Answers: (a) Fn= N, F = N (b) Fn= N, F = the tolerance is +/-2%