The 1.5 m concrete post is reinforced with six steel bars, each with 28 mm diameter. Knowing the Es = 200 GPa and Ec = 200 GPa, determine the normal stresses in the steel and concrete when a 1550 kN axial centric force P is applied to the post.

Q: For the connection shown, the average shear stress in the 16-mm-diameter bolts must be limited to…

A: Givend=16mmAverage shear stress=260Mpa

Q: A cantilevered supporting member with a length and diameter of 20cm and 2cm, respectively, is…

A:

Q: If the cross section of the femur at section a–a can be approximated as a circular tube as shown,…

A: Considering the equilibrium of femur,

Q: The boom AB is made up of a hollow square 80-mm tube having a wall thickness of 2 mm. A 20-mm…

A:

Q: The rectangular beam ABC, 148 mm wide by 476 mm deep, is supported by a pin at A and the cable CD.…

A:

Q: The plate welded to the end of the l-beam is fastened to the support with four 10-mm-diameter bolts…

A:

Q: The compressed air tank AB has a 250-mm outside diameter and a 10-mm wall thickness. The arm BC is…

A: Stress calculations:

Q: Steel wire AB and aluminum wire CA support the 400 kg mass as shown. Determine the required diameter…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

A:

Q: The steel bracket is used to connect the ends of two cables. If the allowable normal stress for the…

A: Given data

Q: [2.37] The 1.5 m concrete post is reinforced with six steel bars, each with 28 mm diameter. Knowing…

A:

Q: The bars of the truss each have a cross sectional area of 1.25 in^2.  If the maximum average normal…

A:

Q: Determine the largest weight W that can be supported by the two wires AB and AC: The working…

A:

Q: The truss shown consists of wooden members. Knowing that each member has a 100 x 100 mm. square…

A:

Q: Link BD consists of a single bar 30 mm wide and 12 mm thick. Knowing that each pin has a 10 mm…

A:

Q: The boom AB is made up of a hollow square 100-mm tube having a wall thickness of 5 mm. A 10-mm…

A: Given data, Outer dimension of hollow boom AB is 100 mm and thickness is 5 mm. So, cross-sectional…

Q: If the allowable tensile stress of the wires AB and AC is oallow = 250 Mpa, determine the largest…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

A: Given Data The load acting at A is PA=80 kN. The load acting at B is PB=280 kN.  The ultimate…

Q: The AB and BC rods have a diameter of 5mm. If a load P = 2kN is applied to the ring, determine the…

A:

Q: Two hydraulic cylinders are used to control the position of the robotic arm ABC. Knowing that the…

A: a) Draw free body diagram of member ABC Force in rod AE can be determined as Stress in rod AE can…

Q: P 90 mm - 80 mm B A -100 mm

A: as per given question determine the stress at a) point A , b) point B.

Q: The 1-in.-diameter bent rod is subjected to the load shown. Determine the maximum torsional stress…

A: Given data The diameter of the rod, d = 1 in. Draw the free-body diagram of the rod. Under…

Q: The 1.5 m concrete post is reinforced with six steel bars, each with 28 mm diameter. Knowing the Es…

A: Given that , L=1.5md=28mmEs=Ec=200GPaP=1550kN

Q: The 4.5-ft concrete post is reinforced with six steel bars, each with a 118-in. diameter. Knowing…

A: Given data:  The concrete post is reinforced with six steel bars as shown in the fig. Diameter of…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The…

A:

Q: For the connection shown, the average shear stress in the 6-mm-diameter bolts must be limited to 176…

A:

Q: The block is subjected to the eccentric load shown. Determine the normal stress developed at points…

A:

Q: 2. The homogeneous 1000-lb plate is suspended from three cables. Determine the smallest diameter…

A:

Q: Determine the stress at points A and B, (a) for the loading shown, (b) if the 60-kN loads are…

A: The given loading condition is centric.

Q: Determine the normal stress in the element GF if the area is 10 in2, knowing that the load W is…

A: Given data Area(Ac)GF=10in2 load (W)=1500lb

Q: Determine the average normal stress in each of the 20-mm-diameter bars of the truss. Set P = 40 kN.

A: Given: The length of AB is AB=2 m. The length of AC is AC=1.5 m. The magnitude of the force P is…

Q: A 60-N-m couple is applied to the steel bar shown. (a) Assuming that the couple is applied about the…

A: Given, Couple M = 60 Nm E = 200 GPa = 200 X 109 Pa b = 12 mm h = 20 mm

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

A: Given data: σ=345 MPa Need to determine the minimum diameter required for the rod.

Q: For the connection shown, the average shear stress in the 15-mm-diameter bolts must be limited to…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A:

Q: Knowing that P= 38 kN, determine the maximum stress when (a) r= 10 mm, (b) r =16 mm, (c) r= 18 mm

A: Given that, Allowable load, P=38 kN,Width at upper section, d=60 mm,Width at lower section, D=120…

Q: Each of the four vertical links has an 8 x 36-mm uniform rectangular cross section, and each of the…

A:

Q: Rods AC and BC are used to suspend the 200-kg mass. If each rod is made of a material for which the…

A: Given data: Maximum allowable normal stress, σmax = 150 MPa. Mass of the suspended block, m = 200…

Q: The steel pipe AB has a 72mm outer diameter and a 5mm wall thickness. Knowing that the arm CDE is…

A:

Q: Q1: A 6-kips force is applied to the machine element AB as shown. Knowing that the uniform thickness…

A: given data  P = 6 kips cross section = 0.8 × 3 in^2 find combined normal stress at point a and f.

Q: Knowing that P= 90 kips, determine the largest distance a for which the maximum compressive stress…

A: Area, A=(5in)(6in)-2(2in)(4in)=14 in2 MOI about the x-axis,  Ix=112(5)(6)3-2(112)(2)(4)3=68.67in4…

Q: vo solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A:

Q: The cylindrical tank AB has an 8-in. inner diameter and a 0.32-in. wall thickness. Knowing that the…

A: given: The diameter of the tank, d = 8 in The thickness of the tank, t = 0.32 in The pressure inside…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A:

Q: Knowing that the clamp shown has been tightened until P= 400 N, determine (a) the stress at point A,…

A: Given Applied load = 400 N To find Stress at point A Stress at point B Location of neutral axis

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

A:

Q: Knowing that the magnitude of the horizontal force P is 8 kN, deter-mine the stress at (a) point A,…

A: P=Compressive force=8 kN

Q: The 1-in.-diameter bent rod is subjected to the load shown. Determine the maximum torsional stress…

A: Given, Force, F=300 i+400 j-200 k lb The diameter of the rod, d=1 in

Q: The tube shown has a uniform wall thickness of 12 mm. For the given loading, determine (a) the…

A: Given: Wall thickness if the tube is 12 mm.

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.