Each of the four vertical links has an 8 x 36-mm uniform rectangular cross section, and each of the four pins has a 16-mm diameter. Take P 24 kN. 04 Determine the maximum value of the average normal stress in the links connecting points Cand E (Input the answer with the appropriate slgn.) The maximum value of the average normal stress in the links connecting points Cand Eis MPa.

Each of the four vertical links has an 8 x 36-mm uniform rectangular cross section, and each of the four pins has a 16-mm diameter. Take P 24 kN. 04 Determine the maximum value of the average normal stress in the links connecting points Cand E (Input the answer with the appropriate slgn.) The maximum value of the average normal stress in the links connecting points Cand Eis MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.14P: Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82...

See similar textbooks

Similar questions

The homogenous bar that weighs 5000 Ib is supported by a pin at Cand a cable that runs from A to B around the frictionless pulley at D. If the diameter of the cable is 0.8 inch, calculate its axial stress. Express your answer in ksi (kips per sq. inches) with one decimal place only (Note: Give only the numerical value of the answer. DO NOT INCLUDE THE UNIT IN THE ANSWER) * D F 3 ft 5 ft 5 ft
Answer the ff correctly. The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal pressure of 15 N/mm2 and an external pressure of 5 N/mm2. Determine and sketch curves showing the distribution of the radial and circumferential stress across the section using Lame’s equations.
E. SOLVE FOR THE STRESS OF in the aluminum IF ITS CROSS-SECTIONAL AREA IS 2500mm^2. P=25KN
3. The vertical force F applied at A is 50 kN. Compute the minimumdiameter of the steel wire, if the allowed elongation on steel wire4mm and its stress is limited to 250 MPa. Use Est = 200 GPa. Answer: d = ___________________
Q1/ A bracket is supported by means of 4 rivets of the same size. Design the 7. Alalkau diameter of the rivet if Ou (tenşile ultimate stress) for the rivet material is 560MPA. Which of the rivet has max resistance? 20KN 20KN B0mm 30 mm 30 mm 30 mm
Use 32 in2 and 48 in2 cross-sectional areas for tensile and compressive members, respectively. Determine the axial stress in member CH in psi. (Numerical absolute answer only without units in 3 decimal places)
The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 80 mm and its thickness is 25 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket.just bearing stress in the rectangular bar. Rectangular bar Support bracket
Current Attempt in Progress The rectangular bar is connected to the support bracket with a 11-mm-diameter pin. The bar width is w-70 mm and the bar thickness is 10 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot ex t exceed 100 MPa, the bearing stress in the bar cannot exceed 150 MPa, and the bearing stress in the bracket cannot exceed 140 MPa. Determine the maximum value of Pax that can be supported by the structure. Answer: Pax 3 KN
The circular column is subjected to a compressive force of 5kN if the stress in the column is limitedto 17.63MPa, what is the limiting value of diameter d?
7. Determine the stress developed in the Tensional Cord given that the cable's diameter is 0.6 inches and the bar weigh 6kips. Figure P-106 3 m 5 m 5 m E
The bolt shown on the picture is subjected to total tensile force of 90 kN. Determine the tensile stress at the body of the bolt and tensile stress at root of bolt. Find also the compressive stress at the head as the bolt bears on the surface to resist the tensile load.