show schematic drawings, conversions, units and box in your final answers Determine the amount of energy (kJ) that needs to be transferred to the water to raise its temperature to 140°F if a water heater is initially filled with 50 gallons of water at 64.4°F.

show schematic drawings, conversions, units and box in your final answers Determine the amount of energy (kJ) that needs to be transferred to the water to raise its temperature to 140°F if a water heater is initially filled with 50 gallons of water at 64.4°F.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The left side of this equation tells how much energy Q the cylinder gives to the water while it cools. The right side of this equation tells how much energy Q the water and aluminum cup absorb from the cylinder to warm up. Because it is the same energy, they are equal. What is known in this equation? Mcyl 411.7 g, malum 46.5 g, malum+water = 175 g Can you find: mwater =? g Twater = Talum = 20°C (water and cup of room temperature) 90°C, T; = 35°C (hot cylinder and cool "cylinder+cup+water" temperatures) Tcyl kCal Calum = 0.22, Cwater 1 (specific heat of water and aluminum, measured in units kg-°C What are we looking for is Ccul - How we find it? Plug all the numbers into the equation (1), Ccul will be one unknown which you can calculate from the equation. Important, convert all the masses from grams to kilograms! After you find Ccyl, compare it to known value for the copper 0.093(our cylinder is made out of copper). |Ceyl -0.093| % : · 100% 0.093
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. B) the weight in tons of the liquid if full tank local gravity is 32.1 ft/sec squared. C) volume of the tank in metric gallons. D.) how many drums will be needed to transfer all of the tank contents (tank being full) to the drums?
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. Flow Rate and Time
An automobile reaches 120,000 miles. The dash calculator has never been reset and indicates an overall average speed of 32 ½ mph: How many hours has the engine been running? At a guess, the average rpm of the engine has been 1750. How many revolutions has the engine completed?
A closedtank of a certain gas receives heat from being exposed to the sun. The bourdon pressure gauge initially reads 20 kpa but after some time it reads 30 kpa. The initial temperature of the gas is 10C but it rises to 30C after some time: Find the ff: A. initial and final temperatures in °F,?,????.B. the change in temperature in °C,°F,?,????. please use 2 decimal places for your solution & final answer
If an engine that throws 200 kW of heat energy into the atmosphere produces 150 horsepower (hp), what is the efficiency of this engine? TIP: Horsepower is not included in the international unit system, you must convert it to kW.
incomplete units/solution. Box your final answer and round to the nearest 2 DECIMAL PLACES 1.63 Ib of gas is stored in a tank of 2ft3. If the internal energy decreases by 27.4 BTU as temperature drops from 200F to 100F, find the specific heat at constant volume for this gas • A closed gaseous system undergoes a reversible process with constant pressure of 200kpa. 2500 kJ of heat is rejected, and the volume changes from 5m3 to 2m3. Find the change in internal energy An Ideal gas with R=25.9 Ib-ft/lb-R and k=1.1 is heated at constant volume. What is the a.) Cp and Cv? b.) mass if it initially it had a volume of 15 ft3, pressure 70 psia, and 540 R? c.) What is the final temperature if 20 Btu is added?
SHOW THE TABLE USED! A fixed amount of carbon dioxide goes through a polytropic process where n=1.4. The initial temperature of the CO2 is 250 K. The final temperature of the CO, is 400 K. If the mass of the CO2 is 12 kg and behaves as an ideal gas, determine the work, the change in internal energy, and the heat transfer during the process (in kJ). Note that PV=mRT. In this problem, can the carbon dioxide be considered an ideal gas at the initial conditions if the initial pressure is 150 kPa? Justify your answer quantitatively.
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
1. Energy consumption in a country from 2001 to 2011 increased from 1041.3 million to 1526.1 million BOE (barrels of oil equivalent). If the high calorific value (HHV) of the oil is 141,000 kJ/gallon what is the increase in energy consumption over 10 years in Joule units. What is the rate of energy consumption per year? 2. Based on data on the rate of energy consumption per year from question no. 1, if the growth rate energy 2.5% per year, calculate the doubling time (td) and what is the approximate rate of energy growth in 2021.
Please provide equations that you are using so I can follow along and learn how to do this and include conversions and units. In Jamestown, NY, a coal power plan consumes coal at a rate of 80 tons/hr. When coal burns, it generates approximately 30,000 kJ for every kg of coal burned. The cooling course for the plant is the nearby Chadakoin River nearby and, by code, the power plant cannot reject more than 13.19 x 109 MJ into the river annually. Determine the maximum average power output of this plant and it's maximum thermal efficiency. To check your work, enter the efficiency, as a decimal, in the box provided.
Given the table of results, find the following. Give answers in KW. Please use tables and state which table you used Please show all working out Rate of heat transfer to evaporator from the chilled water: Answer : 0.627 kW ✓ Rate of heat transfer from condenser to the cooling water: Answer : 0.81kW✓ Rate of heat transfer to refrigerant in “Evaporator” using enthalpy values: Rate of heat transfer from refrigerant in “Condenser” using enthalpy values Work input from the compressor to the refrigerant using enthalpy values. Answer: 0.470kW ✓ COP from enthalpy changes across work input and evaporator COP from motor electrical power input as work and rate of heat transfer to the chilled water