s shown in the figure, two aluminum rods AB and BC, hinged to rigid supports, are pinned together at B to carry a vertical load P = 30 kN. Each rod has a cross section al area of 400 mm2 and E = 70x103 MPa . Assume α = 300 and θ = 450 . Find: (a) the deformation of rod AB. Indicate If elongation or shortening (b) the deformation of rod BC. Indicate If elongation or shortening (c) stress in rod AB. Indicate if tension or compression (d) stress in rod BC. Indicate if tension or compressio

s shown in the figure, two aluminum rods AB and BC, hinged to rigid supports, are pinned together at B to carry a vertical load P = 30 kN. Each rod has a cross section al area of 400 mm2 and E = 70x103 MPa . Assume α = 300 and θ = 450 . Find: (a) the deformation of rod AB. Indicate If elongation or shortening (b) the deformation of rod BC. Indicate If elongation or shortening (c) stress in rod AB. Indicate if tension or compression (d) stress in rod BC. Indicate if tension or compressio

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.16P: Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020...

See similar textbooks

Similar questions

1 = the 0.18 LONG M. 2.F MJ CS.G Find 10.1m 04 10 to Tam bo Eli Revo do (^~^-h^) 5.8m1 Y Z 6.3m A B 7.3m La Orque с FL X Criven: posimon Vector for Force D, E, F 0 = (0₁5.8, 07 E = L 6.3 15,9,0) F = L13.6 15.9, 07 f D = 4.19KN E = 5.36 KN magnitude of the moment about org.in due to this force? F = 10.2 KN
Ex ملم 2 KNY 9-2m dy=3m EXL VTVL 7m 2 5KN/ subject is slope and deflation find y at 2m from the left hand ју atэм dx 7
16cm. 34.8cm = 1.0 SGcone = 0.9 Which is the more stable pesiton? IS
A cable with supports at the same elevation has a span of 300m. The cable weighs 75 N/m and the sag at midspan is 75 m. Determine The length of the cable.
Fig.(4) B 250 N D 2m 2 mi Roller E -1.5m-1.5m-1.5m-1.5 m-
Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020 (channel with a nominal depth of 10 in., weighing 201b/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following properties for the cross section: A=5.88in.2,Ix=78.9in.4, and Iy=2.81in.4. If two of these channels are welded together as shown in Fig. (b), find Ix and Iy for the resulting cross section.
Determine the following: a. Shear and Bending Moment Equation b. Shear and Bending Moment Diagram c. Mmax 15 kN/m B 10 m 5 m
calculate total moment at... At point O in this system. 500 N Choose... 3 m Choose... 45 2234NM 1060NM 4070NM 3111NM 1805NM 1254Nm
Q1(a) Cross section of a beam is as shown in Figure Q1(a),determine; (i) center of gravity with respect to bottom edge AB; (ii) second moment of area of the section about AB. 200 300 100 A B Figure Q1(a) (take all dimensions in milli meters) (b) If a concentric hole of diameter100 mm drilled on the circular section in Q1(a), explain its effect on the center of gravity with respect to 'AB'.
40 N 30 N B -3m -3 m 50
For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. = 350 Ibf, V2 = 31 Ibf/in, V3 = 10 in, and V4 = 5 in. v1 v2 v4 v4 Provide values at all key points shown in the given shear-force and bending-moment diagrams. n v IVn me A B 0.00 R D 0.00 P Shear Diagram in.) The reaction force Ro= The bending moment Mo= Ibf. Ibf-in. In the shear-force and bending-moment diagrams given, A = B = LIbf Ibf C= Ibf D= Ibf P= Ibf-in Ibf-in R= Ibf-in
01-B- Draw just the Free Body Diagram of the following figures. 30 kN/m Fig. (2) AB -3 m- Fig. (4) 4 kN/m +3m- 8 kN/m 4 m -3 m 10 kN/m 3 m 2 kN/m B Fig. (3) Fig. (5) Nim 3 m -3m- -3 m- 80 kN/m