R3 E1 R4 R2 R1 E2 Figure 3 With respect to circuit above, use the Superposition Theorem to find the current through R2 if E1 19 V and E2 14 V, R1 = 5.3 k2, R2 = 6.9 k2, R3 = 11.2 k2, %3D %3D and R4 = 13.2 k2. %3D I) If only E1 is in the circuit, what is the current through R2? Current through R2 = %3D II) If only E2 is in the circuit, what is the current through R2? Current through R2 = III) Finally, what is the net voltage across R2 when both El and E2 are in the circuit? (If the net current through R2 is downward (which means +ve voltage is at the top of R2) enter answer as positive; if the net current is upward (which means the -ve is at the top of R2) enter answer as negative) Net voltage across R2 = V

R3 E1 R4 R2 R1 E2 Figure 3 With respect to circuit above, use the Superposition Theorem to find the current through R2 if E1 19 V and E2 14 V, R1 = 5.3 k2, R2 = 6.9 k2, R3 = 11.2 k2, %3D %3D and R4 = 13.2 k2. %3D I) If only E1 is in the circuit, what is the current through R2? Current through R2 = %3D II) If only E2 is in the circuit, what is the current through R2? Current through R2 = III) Finally, what is the net voltage across R2 when both El and E2 are in the circuit? (If the net current through R2 is downward (which means +ve voltage is at the top of R2) enter answer as positive; if the net current is upward (which means the -ve is at the top of R2) enter answer as negative) Net voltage across R2 = V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the branch current of R1. 400- RI 680 1 R2 R3 900 |-|-
For R1=55, R2=D125, R33D135, R4=15, R5=40, R63D90 and V1=4 V in the shown figure, use circuit reduction and current/voltage division rules to calculate the following: R6 R1 R5 R3 R2 V1 V2 R4 V13= V2=
The purpose of this problem is to demonstrate that you know how to apply Kirchoff's Rules, you are not required to actually solve for the currents. Knowns: V, R1, R2, R3, R4 a) Label all the currents in the circuit. b) Draw and label all possible closed loops. c) Label each node. d) Apply Kirchoff's Loop rule to all of your labeled loops (set up the equations for each loop). e) Apply Kirchoff's Node rule to all of your labeled nodes (set up the equations for each node). Extra credit: Find the values for your labeled currents using any method you choose R2 R, R, 6V 3V R,
How does the voltage across R1 compare with that through R2? What is the connection between the total current in the circuit and the current through the two resistors? (This is known as Kirchhoff's junction rule.) ... R1 R2 Circuit 4 If you use Circuit 5, do the same rules apply? R1 R2SR3 Circuit 5
For R1=50, R2=60, R3=40, R4=10, R5=40, V1=45 V, V2=30 V & I1=9 A in the circuit shown below, apply source transformation to find Vx (in volt) V1 R1 Oa. -28.405797101449 Ob. 14.202898550725 Oc. -14.202898550725 Od. -42.608695652174 where V = R3 ww V R2 where R = R5 The circuit after source transformation will be as follows: R3 R4 V2 The circuit after source transformation will be as follows: R3 ww
Refer to the following circuit diagram. Find the current Is1 supplied by source E₁. and current Is2 supplied by E2. E₁ 130V Ist A Z₁ 3352 N Z₂ 1052 B D Z₁ 2402 Z 502 C Isz E₂ 110V
"MILLMAN’S THEOREM " Please Find the Current and Voltages in 6k , 3k , 6k Ohm Resistors only, with a total of 3 currents and 3 voltages to compute Using NMILLMAN’S THEOREM thankyou very much ! I've included a cicruit app to check if your answer was correct and close to the value of currents and voltages thankyou! I've been testing simple circuits to practice problems using different theorems,I appreciate you very much Thankyou!
In the circuit below, the currents through the four resistors are as indicated. Use the junction rule to write the equations representing the relationship between the currents at the point d. (Use the following as necessary: 14, 15, and 16.) 16=14+15 X = 0 &₁ 15 R4 d E₂ =&
Sy A circuit design calls a 1.5 kN resistor to have 4.7 V across its terminals. What would be the expected current? The circuit is built, and the resistance is measured at 1500 2 and the voltage at 4.7 V. What is the current through the resistor? f is ie
R1 2200 R2 5000 E1 -12 V E2 -50 V R3 3000 For the figure shown above : Find 11, 12, 13, V1, V2,& V3
Consider the circuit in the figure. Use the included current directions (arrows) and component labels. a) Which of the following equations would be the correct equation for the junction labeled c? - I1=I2+I5 - I2=I1+I3 - I1=I2+I3 - I1=I2+I4 B) Which of the following equations would be the correct equation for the junction labeled d? - I3=I4+I5 - I3+I4=I6 - I3+I4=I5 - I3+I5=I4 C)Which equation for the junction labeled g? - I6+I5=I4 - I6+I4=I5 - I6+I4=I6 - I6=I4+I5 D) Now you have the junction specifying each current. What is the accurate representation of the loop a=>b=>c=>h=>a? E) What is the accurate representation of the loop equation a=>b=>c=>d=>g=>h=>a? F)What is the accurate representation of the loop equation for loop d=>e=>=>g=>d? (Make sure you follow the directions of the currents drawn)
To measure the change in resistance of the gage(s) and indicate the location of the gauge on the beam, construct the Wheatstone bridge circuit. Calculate the Wheatstone bridge output if the gauge indicates a strain of 4000.then,Evaluate how can the number of strain gauges affects your measurement result. Justify your response with a calculation and a diagram showing the gage's placement on the beam.