E1 R4 R2 R1 E2 Figure 3 With respect to circuit above, use the Superposition Theorem to find the current through R4 if E1 = 32 V and E2 = 18 V, R1 = 150 2, R2 = 284 , R3 = 461 2, and R4 = 100 . I) If only E1 is in the circuit, what is the current through R4? current through R4 = II) If only E2 is in the circuit, what is the current through R4? current through R4 = III) Finally, what is the net current through R4 when both E1 and E2 are in the circuit? (If the net current through R4 is downward enter answer as positive; if the net current is upward enter answer as negative) net current through R4=

E1 R4 R2 R1 E2 Figure 3 With respect to circuit above, use the Superposition Theorem to find the current through R4 if E1 = 32 V and E2 = 18 V, R1 = 150 2, R2 = 284 , R3 = 461 2, and R4 = 100 . I) If only E1 is in the circuit, what is the current through R4? current through R4 = II) If only E2 is in the circuit, what is the current through R4? current through R4 = III) Finally, what is the net current through R4 when both E1 and E2 are in the circuit? (If the net current through R4 is downward enter answer as positive; if the net current is upward enter answer as negative) net current through R4=

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter33: Single-phase Motors

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

Find the branch current of R1. 400- RI 680 1 R2 R3 900 |-|-
In the circuit below, the currents through the four resistors are as indicated. Use the junction rule to write the equations representing the relationship between the currents at the point d. (Use the following as necessary: 14, 15, and 16.) R₁ www = 0 W €₁ 1₁ R₂ 1₂ R3 a 13 E4 16 15 R4 E2 E3
In the circuit below, the currents through the four resistors are as indicated. Use the junction rule to write the equations representing the relationship between the currents at the point d. (Use the following as necessary: 14, 15, and 16.) 16=14+15 X = 0 &₁ 15 R4 d E₂ =&
To measure the change in resistance of the gage(s) and indicate the location of the gauge on the beam, construct the Wheatstone bridge circuit. Calculate the Wheatstone bridge output if the gauge indicates a strain of 4000.then,Evaluate how can the number of strain gauges affects your measurement result. Justify your response with a calculation and a diagram showing the gage's placement on the beam.
"MILLMAN’S THEOREM " Please Find the Current and Voltages in 6k , 3k , 6k Ohm Resistors only, with a total of 3 currents and 3 voltages to compute Using NMILLMAN’S THEOREM thankyou very much ! I've included a cicruit app to check if your answer was correct and close to the value of currents and voltages thankyou! I've been testing simple circuits to practice problems using different theorems,I appreciate you very much Thankyou!
For R1=55, R2=D125, R33D135, R4=15, R5=40, R63D90 and V1=4 V in the shown figure, use circuit reduction and current/voltage division rules to calculate the following: R6 R1 R5 R3 R2 V1 V2 R4 V13= V2=
How does the voltage across R1 compare with that through R2? What is the connection between the total current in the circuit and the current through the two resistors? (This is known as Kirchhoff's junction rule.) ... R1 R2 Circuit 4 If you use Circuit 5, do the same rules apply? R1 R2SR3 Circuit 5
Quiz 1 For the circuits given below use superposition theorem and find the voltage and current across R2 and R3 VS2 R3 Vs1 R1 R2 R4 Vs1 = 10V, VS2315, R1=100, R2=150, R3=200, R4=250
the follow up question wasnt answered properly the question wasnt about the superposition theorm it was about ic1=5<60 /.... and ic2=4+j4 .... can you please explain how you got both formulas in detail? thank you.
im new to the concept of nodal analysis so when finding vab u applied nodal analysis to get v1 but on what basis did you put the values in the numerator and denominator? and what part of the circuit did you not take into account while calculating it? since there seem to be some missing values. i mean what does each number refer to. also when calculating vth and used v1 to find it how did u get x2/2+1? i know about the voltage division rule but im a bit confused can you please elaborate on all these points?
Refer to the following circuit diagram. Find the current Is1 supplied by source E₁. and current Is2 supplied by E2. E₁ 130V Ist A Z₁ 3352 N Z₂ 1052 B D Z₁ 2402 Z 502 C Isz E₂ 110V
According to the circuit and parameters given in the figure, make your calculations and write the table. wmww w n ww bbn m w w w w Please fill in. www ww w +12V +12V M1 M2 2kN 10kN K ImA/V² 0.5mA/V² VTH 2V 1.5V 22kN M2 MODE 33k2 M1 Ip 1kN VGS Vps K1=lmA/V² Vth1=2V; M2: K2=0.5mA/V² VTH2=1.5V