Q5/ The information in an analog waveform with maximum frequency fm = 3 KHz is to be transmitted over M-level PCM system where the number of quantization levels is M = 16. The quantization distortion is specified not to exceed 1% of peak-to-peak analog signal. %3D What would be the maximum number of bits per sample that should be used in this PCM system? What is the minimum sampling rate and what is the resulting bit transmission rate? i) ii)

Q5/ The information in an analog waveform with maximum frequency fm = 3 KHz is to be transmitted over M-level PCM system where the number of quantization levels is M = 16. The quantization distortion is specified not to exceed 1% of peak-to-peak analog signal. %3D What would be the maximum number of bits per sample that should be used in this PCM system? What is the minimum sampling rate and what is the resulting bit transmission rate? i) ii)

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.3: Signal System

Problem 1R

See similar textbooks

Similar questions

5- Discuss the effect of changing the number of bits on the recovered analog waveform. 6- Discuss the effect of changing the frequency of input analog signal on the reconstructed analog output signal.
The information in an analog voltage waveform is to be transmitted over a PCM system with a 10.1% accuracy (full scale). The analog waveform has an absolute bandwidth of 100 Hz and an amplitude range of -10 to +10 V. (a) Determine the minimum sampling rate needed. (b) Determine the number of bits needed in each PCM word. (c) Determine the minimum bit rate required in the PCM signal. (d) Determine the minimum absolute channel bandwidth required for transmission of this PCM signal.
Q2/ The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of ±0.1% (full scale). The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of -10 to +10 volts. Find the minimum sampling rate required. i) ii) Find minimum bit rate required in the PCM signal. Find the number of bits in each PCM word. iii) iv) Find the minimum absolute channel bandwidth required for the transmission of the PCM signal.
discrete state. 3. A BCD counter can assume 4. A BCD counter can divide its input signal frequency by
In a PCM system, if maximum frequency of the input analog signal is 5 KHz and number of levels in the quantizer is 256. What will be bandwidth of the transmitted PCM signal?
What do you mean by fractional sampling rate conversion? Explain with an example of converting 48 kHz signal to 44.1 kHz signal using multi-stage fractional sampling rate converter
6. Which of the following is not a type of signal is... a. analog signalb. Chain signalc. Binary signald. Dict signale. digital signal
Q5/ The information in an analog waveform with maximum frequency fm transmitted over M-level PCM system where the number of quantization levels is M = 16. The quantization distortion is specified not to exceed 1% of peak-to-peak analog signal. = 3 KHz is to be i) What would be the maximum number of bits per sample that should be used in this PCM system? (ans,n = 4 bits) What is the minimum sampling rate and what is the resulting bit transmission rate? ii) (ans.r > 24 x 103 bits/sec)
Problem 2: The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of ± 0.1 % of the peak-to-peak analog signal. The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of – 10 to + 10 Volts. Determine the minimum sampling rate required. b. Determine the number of bits in each PCM word. c. Determine the minimum bit rate required in the PCM system. d. Determine the minimum absolute channel bandwidth required for the transmission of the PCM signal.
In ADC circuit ,the input will be ........... signal.
Assuming that a certain ASM chart has 5 states, the size of each multiplexer required to implement this circuit using the multiplexer design approach should be: Select one: O a. Four to one. O b. Eight to one. O . None of the given. O d. Two to one.
(b) Consider a voice signal from a analog telephone which needs to be digitized. Explain the steps involved in the conversion of analog to digital signal. If suppose the sampled analog values are 1V, 2V, 3.5V and 4.5V, use a 2 bit quantizer to digitize these values. Assume the range of sampled analog values from 0V to 5V. Provide the digitized values of this signal and draw the digital signal.