Q4/For the lap joint shown in the Figure, calculate the safe axial tensile force (P); if: Tensile stress )allow.=136 MPa Shear stress rivet)allow.=102 MPa Bearing stress)allow.=330 MPa Assume the diameter of hole =25mm.? * 022mm rivet P Plan P section 300mm

Q4/For the lap joint shown in the Figure, calculate the safe axial tensile force (P); if: Tensile stress )allow.=136 MPa Shear stress rivet)allow.=102 MPa Bearing stress)allow.=330 MPa Assume the diameter of hole =25mm.? * 022mm rivet P Plan P section 300mm

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter22: Welding Joint Design And Welding Symbols

Section: Chapter Questions

Problem 4R: Sketch a V-grooved butt joint, and label all of the joint's dimensions.

See similar textbooks

Related questions

Q: a. Take a cut through the section where the AB and BC segments are connected (shown in the figure at…

A: we are to determine the stress distribution at section B, and the load at point C

Q: Two steel tubes are joined at B byfour pins (dp = 11 mm), as shownin the cross-section a-a in…

A: given: the diameter of pin, dp = 11 mm the outer diameter of tubes dAB =40 mm the outer diameter of…

Q: The figure shows a roof truss and the detail of the connection at joint B. Member BC and BE are…

Q: The rigid bar A,B,C,D shown in figure is connected to the ground by a hinge at B and to Magnesium…

Q: Referring to figure assume that the diameter of the rivet that joins the plates is d = 20 mm. The…

Q: 1.6-4 The inclined ladder AB supports a house painter (82 kg) at C and the self weight (q = 36 N/m)…

Q: 3.3-13 A vertical pole of solid circular cross section is twisted by horizontal forces P= 1100 Ib…

A: GIVEN :- P=1100lb c=5.0in τallow=4500psi SOLUTION :-we know that,τmax=TrJ=Td2Jwhere…

Q: The figure shows a roof truss and the detail of connection at joint I. The allowable stresses are 70…

Q: 4. The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet…

Q: 2) Design the fillet weld for direct shear connection for the angle loaded as shown in the figure.…

A: INTRODUCTION: The fillet weld and the butt weld are two different types of weld joints, according to…

Q: Question Completion Status: QUESTION 8 Consider the circular bent rod with diameter 20 mm. The…

A: We have to determine shear stress

Q: P = 500 N pressing force to the wooden blocks between the jaws. It case; a) Calculate the greatest…

Q: Problem 1.7-5 The force in the brake cable of the V-brake system shown in the figure is T- 200 N.…

Q: PROB. 3.8-3 3.8-4 A hollow steel shaft ACB of outside diameter 50 mm and inside diameter 40 mm is…

Q: The rigid beam is supported a pin connection at A and a cable BD at point the. Diameter of pin at A…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: 8. The figure shows a roof truss and the detail of the connection at joint B .Members BC and BE are…

Q: The screw clamp shown in the figure applies a P = 500 N pressing force to the wooden blocks between…

Q: The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are…

A: given; ⇒stress(τ)=70MPa⇒diamater(d)=20mm⇒lets take number of rivit in BC =n1 ⇒lets take reaction…

Q: A single shear lap-joint connection is shown in the figure, If P-10,825 N, d-22 mm, and t-38 mm,…

A: Given data P=10.825 Nd=22 mmt=38 mm Here, P is the load, d is the diameter and t is the thickness.…

Q: Q4(10 Marks): For the structure shown in the figure, calculate the size of the bolt and the area of…

A: σAT=Allowable Stresses in Tension=124 MPaσAB=Allowable Stresses in Bearing=3.44 MPa

Q: 4 kN 3 kN 375 mm 375 mm B 750 mm As shown in the figure, the shaft is supported by bearings A and B…

A: Given data Material used A36 Diameter of the shaft = 50mm To determine the maximum theoretical…

Q: 3- A bracket, as shown in Fig., carries a load of 10 kN. Find the size of the weld if the allowable…

A: Welding is method of joining two similar or dissimilar metal with or without heat , or with or…

Q: 1. In the figure shown, determine the stress in the cable C if its area is 600 mm². Neglect the…

Q: 3. Given the following data of the figure shown : P= 3.5 KN, L, = L, = L, = 1.5 m Strut BC = 100 mm…

Q: 1.45 The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: QUESTION 1) A channel type cross-section is subjected to the compression force P-20 kN at the point…

A: The section is as shown below, The area of the section is, A1=20×5=100 cm2A2=20×5=100…

Q: 4. The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet…

Q: Droblem 6.4: Each member of the truss in Figure (6.21) is a solid circular rod with diameter d=10…

Q: A cantilever wood beam consists of eight 2 in. thick planks glued together to form a cross section…

Q: In the ship crane in the figure, at the D and A supports, Find the reaction forces. Section area…

Q: Compute the tensile stress for the rod shown in Fig. 1 at section A-A, the shearing stress across…

A: Given: The dimension, n = 7/4 in The dimension, a = 15/32 in The dimension, e = 27/32 in The…

Q: EXH.W.3:- The lap joint shown in figure is fastened by three (23 mm) diameter rivets. Assuming that…

Q: For the joint shown in the figure, if F = 28 kN and dp = 12.8 mm, calculate: 7.5 mm F F 12 mm 12 mm…

Q: The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet has…

Q: -15 m---25 m- - 3 m B 35 m 784,8 kN 15 m

Q: Given inner diameter=45mm thickness=6mm I=200*10^-6 G=30Gpa pressure inside=1.4Mpa 1.the hoop stress…

A: Given data: Inner diameter of cylinder = di = 45 mmthickness of cylinder = t = 6 mmOuter diameter of…

Q: A prospector uses a hand-powered winch(see figure) to raise a bucket of ore in his mineshaft. The…

A: To transmit energy by rotation it is necessary to apply a turning force .in the case of a shaft if…

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have a square…

A: Calculate tension in AB for moment equilibrium about C T x 6 = 20 x 9.5 T = 31.6666 N

Q: While drilling a hole with a brace and bit,you exert a downward force P = 25 lb on the handleof the…

Q: The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet has…

A: The rivet system given above is double riveted butt joint. The mathematical relation to calculate…

Q: OS: As shown in Fgure (4.16), the maximum shear stress at section (a-a is (29.47 MPa). If(b=12 mm)…

A: (1) Draw a free body diagram for the beam. Here, TR is the reaction torque at the fixed end of the…

Q: 2 kip/ft 6 in 10 in A 16 in 40 kip D. 16 In 5 ft 5 ft 10 ft- The simply-supported beam-column above…

A: Given dataInternal resultant on the cross section passing through point D are ND =-40 kipVD = 0MD =…

Q: In the ship crane in the figure, at the D and A supports, Find the reaction forces. Section area…

Q: A. for the lap joint shown below, calculate the safe axial tensile force P if Otensile=136MPa,…

Q: LA rod is composed of aluminum section with diameter of 25mm is rigidly attached between hallow…

Q: The figure below is a bracket which fastened by a bolts with a diameter of 0.5 inch. Compute the…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Q4/For the lap joint shown in the
Figure, calculate the safe axial tensile
force (P); if: Tensile stress )allow.=136
MPa Shear stress rivet)allow.=102
MPa Bearing stress)allow.=330 MPa
Assume the diameter of hole
=25mm.? *
022mm rivet
P
P
Plan
P
P
section
300mm-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

find shear amd Binding momont okagrou 5KN/m 5m Tht 3m 707
1cm t1 (cm) P 3,2 cm t2 (cm) t1 (cm) 1 cm 20 cm Ь (ст) P = 20t %3D Dp=1,6 cm
Q1:Prepare a full-section assembly drawing of the four fastener assemblies shown in the Figure. Dimension both the clearance and the threaded holes. A top view may be shown if required. Scale 1: 1. .250-20 FHMS .375 HEX BOLT AND NUT THREADED INTO BASE 1.00 ↓ .50 T 2.00 Ø.375 STUD THREADED .312 HEX X 1.25 LG INTO BASE FOR 1.00 IN. CAP SCREW AND WITH HEX NUT AND LOCK WASHER ON SPOTFACE SURFACE PLATE WASHER A 2.00- -2.00 -1.00- BASE 1.00- .25 1.50
Pc=nxdxtxo =2x25x20x150 150000 N The strength of the riveted joint= Least of P, Ps , Pc =150 000 N %3D The lap join the edges of There are th %3D 000 050= 02I X 0Z X 001 ='91d=d 0000$ =D0.625 or 62.5 % %3D 0000 a-single tr Homework: 1-A single riveted lap joint is made in 1.5 cm thick plates with 2 cm diameter rivets Determine the strength of the joint, if the pitch of rivets is 6 cm? Take 6,=1200 kg/cm ; o,= 900 kg/cm² ; 6=1600 kg/cm 2-Two plates 16-mm thick are joined by á double riveted lap joint. The pitch of each row of rivets is 9 cm. The rivets are 2.5 cm in diameter. The permissible stresses are as aqnop -4 c-paraller [ans:2827kg] 2. G,=1400 kg/cm ; 6,=1100 kg/cm² ; 6.= 2400 kg/cm 2. Find the efficiency of the joint . 3-A double riveted double cover butt joint is made in 1.2 cm thich plates with 18 mm diameter rivets.find the efficiency of the joint for a pitch of 8 cm. 2. 2. ст Take :6,=1150 kg/cm ; 6, = 800 kg/cm² ; oc=1600 kg/cm 10 mm thick, the allowable stresses are : 6, =…
1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
HOW TO SOLVE: Draw the FBD of one member Solve for the bearing force. Section one bold and solve internal forces. Solve for the normal and shear stress in the bolts. Solve for the bearing stress in the members due to the nuts. Solve for the bearing stress in the members due to bolts. ANSWERS: bearing stress of bolt= 7.96 MPa, T; shear stress of bolt= 13.78 MPa; bearing stress (max)= 18.04 MPa
a) The normal stress in bar BD is most nearly b) The shear stress in the pin at D is most nearly c) The shear stress in the pin at C is most nearly
asap
We will use both shearing and bearing analysis to determine the quantities of rivets needed to fasten BC and BE. We can determine two values then choose what will be more safe. ■ For Member BC: ■ Based on Shearing: V T == ■ Av Based on Bearing: P Ab 70MPa = 96000 N .n. (19) ²x n 1/4. π n = 4.84 5 rivets 96000 N (19mm) (6mm) xn 140MPa n = 46.015≈ 7 rivets For member BC, we must use 7 rivets since we must need a minimum of 7 rivets to resist bearing stress produced by the connection. If we only use 5 rivets, then the bearing stress will become 168.42 MPa. It will result to failure since the allowable bearing stress is only 140 Mpa. ■ For member BE: (Practice at Home) Pac EXAMPLE: 5. The figure shows a roof truss and the detail of the riveted connection at joint B. Using allowable stresses of t = 70 MPa and ob= 140 MPa, how many 19-mm diameter rivets are required to fasten member BC to the gusset plate? Member BE? What is the largest average tensile or compressive stress in BC and BE? Say…
NEED ANSWER ASAP !!! The axial load 274 kN applied to the lap joint is distributed equally among the three 26.5-mm-diameter rivets. What is the bearing stress (in MPa) between a plate and a rivet if w = 135.4 mm and t = 29.5 mm?
Sketch a V-grooved butt joint, and label all of the joint's dimensions.
please box in the following answers: normal stresses for beam AB and BC (mid section) normal stresses for beam AB and BC (at connections A and C) shear stress for pin A, B and C bearing stress along member AB and BC at pin section for A and C 600mm Flat end 40 mm FRONT VIEW d-25 mm d-25 mm 50 mm 125 mm 30 mm 25mm ,20 mm TOP VIEW OF ROD BC -800 mm Q-30 kN TOP VIEW OF BOOM AB d=25mm Flat end Q-30KN 20mm 20 mm END VIEW 600 mm 50 mm 20 mm 800 mm 30 AN 1