Answered: QUESTION 1) A channel type…

QUESTION 1) A channel type cross-section is subjected to the compression force P-20 kN at the point A as shown in the figure. Draw the normal stress distribution on the cross-section.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.14P: The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind...

See similar textbooks

Related questions

Q: QUESTION 2. The elbow-shaped structure is under the effect of four forces that are applied as shown…

A: Given: The inner diameter of elbow, d = 40 mm The outer diameter of elbow, D = 48 mm

Q: Draw the Mohr's Circle of the stress element shown in figure. Find:- 6 MРа A 6 MPa The stresses…

Q: The beam shown below has a cross section of channel shape with width b-400 mm and height h=80 mm,…

A: Answer: (a) The maximum tensile stress is 64.68 MPa. (b) The maximum compressive stress is 16.36…

Q: olve carefully, include the units in every step and draw the diagram. Thanks! In a 2.5 m…

Q: Due to the applied loading, the element at point A on the solid shaft in Figure is subjected to the…

A: σx=-12 ksiσy=0 ksiTxy=-6ksi σavg=σx+σy2=-6ksi R=(12-6)2+62=8.49 ksi

Q: A member has the triangular cross section shown in the figure below. 4 in. 4 in. M -2 in.2 in.…

A: Data given- Allowable tensile stress = 22 ksi Allowable compressive stress = 16 ksi

Q: P=70 MPa . Determine maximum principal stress

Q: Q - (A) // The figure A shown that the beam which is supported with a pin at A and a roller at B,…

Q: 1. In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

Q: Problem 2: It is recommended to change the circular cross section shown in the figure by a square…

Q: In figure shown, the allowable normal stress is 3.5 ksi, allowable shear stress is 1.2 ksi. Ift =…

A: (a) Draw the free-body diagram of joint A.

Q: Figure 1 shows a T-beam section contains a flange of size 120 mm by 10 mm and web of size 20 mm by…

A: The area moment of inertia, also known as the second area moment or 2nd moment of area, is a feature…

Q: H.W: The member shown in Figure has a rectangular cross section. Determine the state of stress that…

Q: Determining the resultant of the internal loads acting on the cross section at C of th

Q: The principal stresses at a point in a critic section of a machine component are o, = 60 MF %3D = 5…

A: Given:σ1=60 MPa,σ2=5 MPa,σ3=-40 MPa,σy=200 MPa

Q: Q 2: A cantilever beam has the profile shown so that it will provide sufficient clearances for large…

A: Given Data: The load acting on the beam is P=115.33 kN. The eccentricity from the neutral axis is…

Q: The figure shows a cross section of simply supported beam with a uniformly distributed load of 4.8…

Q: Using direct stiffness method determine the nodal displacement of stepped bar as shown in the…

Q: A single shear lap-joint connection is shown in the figure, If P-10,825 N, d-22 mm, and t-38 mm,…

A: Given data P=10.825 Nd=22 mmt=38 mm Here, P is the load, d is the diameter and t is the thickness.…

Q: Qr) Find the stress distribution at the section ABCD for the block shown in the figure. Sketch the…

Q: 3 in. 3 in. 3 in. Two vertical forces are applied to a beam of the cross section shown. Determine…

Q: a) A simply supported beam with a rectangular cross section supports uniform load q. (see figure).…

Q: A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure below.…

Q: a = 1.7 ft, b = 3.4 ft, and c = 2.55 ft. P = 3000 lb box beam wall thickness, t = 0.610 in. diameter…

Q: digit of your ID No., mm) and 10 mm thick (plus quarter of the last digit of your ID No., mm). It…

Q: The foundation bolt is shown in the below figure a force F = 300 N. The bolt material is wire of…

Q: An axial load Pis supported by the short steel column shown in the figure. The column has a…

A: Cross sectional area of the column, Acolumn= 16200 mm2 Average normal stress in the steel column,…

Q: Q5(): For the truss shown in the Figure, if the diameter of pins at A and F are 2 in. and 1.5 in.,…

Q: For the I section shown in figure. If the section is subjected to a shear force of 120 kN, determine…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: Problem (4.7): For the thin-wall tubular sections shown in Figure (4.28); (a) Determine the maximum…

Q: Box Beam Box Beam Support at A a b с a = 1.7 ft, b = 3.4 ft, and c = 2.55 ft. P = 3300 lb box beam…

Q: Column is manufactured using concrete (E=4.2×10^3 ksi) and reinforcement is done by A-36 steel rods…

Q: Determine the total stress at point A on the cross section a-a in the figure below. 400 kN la -0.5…

A: Draw a diagram showing the neutral axis for the above-cross section.

Q: Example 3 Determine: a. The shear stress at point B on the web of the cantilevered strut at section…

A: Answer: (a) The shear stress at point B: 8.81735 MPa (b) The maximum shear stress: 9.70434 MPa

Q: Calculate non-zero stress components (normal and shear) at points A, B and C. Point C is located at…

A: Given: The length of the bar→L=100 mm=0.1 m Diameter of the bar→d=15 mm=0.015 m At point A: Because…

Q: An overhanging beam of channel section supports a uniformly distributed load of 10 kN/m and a…

A: Given: The UDL, w = 10 kN/m The concentrated load, P = 20 kN

Q: A horizontal cantilever 2 m long is constructed from z-section shown in Fig. 9.19. A load of 10 kN…

A: As indicated in the illustration, we have a 2 m long horizontal cantilever made of z-section.A 10 kN…

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

Q: The cantilever beam is subjected to a concentrated load of P-32 kips. The cross-sectional dimensions…

Q: Two vertical forces, each of magnitude P= 14 kips, are applied to a beam of the cross section shown.…

A: The question is related to the normal bending stresses produced in the beam due to bending only. The…

Q: A simply supported beam (i.e., with a pin support at point A and a roller support at point D) is…

Q: A simple pin-connected truss is loaded and supported as shown in the figure. All members of the…

A: Given Data:-Outside Diameter=5.00 inThickness=0.274 inload, P=8 kips;Q=8 kips=a=4 ft, b=8 ft &…

Q: 2 kip/ft 6 in 10 in A 16 in 40 kip D. 16 In 5 ft 5 ft 10 ft- The simply-supported beam-column above…

A: Given dataInternal resultant on the cross section passing through point D are ND =-40 kipVD = 0MD =…

Q: P to point A of the section given in the figure Plot the normal stress distribution in the section,…

A: Given dataP=20kN Here are calculation the Moment of inertia about the neutral axis

Q: The cross-section of the beam is rectangular everywhere, and the size of the cross-section is given…

A: Given width of beam w=50mmhieght of the beam h=100mm

Q: Find maximum shear stress Maximum principal stress-8 MPa Minimum principal stress=3 MPa

A: Given data : Maximum principal stress=σ1 Minimum principal stress=σ2 To find : Maximum shear…

Q: (a) Determine the maximum tensile stress and maximum compressive stress o (in MPa) due to the load P…

Q: 30 kN ww Β 4 m 2 m Formüller: F.L F F σ-Ε.ε, ε-, ΔL- α.LΔT, ΔL Α.Ε. Α A

Question

100%

Please correct answer

QUESTION 1) A channel type cross-section is
subjected to the compression force P-20 kN at
the point A as shown in the figure. Draw the
normal stress distribution on the cross-section.
20cm
X.-
Scm
5cm
15cm cm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the resultant force at the support A?
Q3) a) Draw the free-body diagram for beam shown in the figure and determine the internal normal force and the normal stresses at the cross-sections a-a and b-b. d = diameter R=3 F-750N d=10mm 300 mm- a a ,=2870 N F27 -200 mm- d=16 mm 100 mm
Determine the maximum tensile and compressive stresses in portion BC of the beam, under loading conditions of two vertical forces that applied on it. The beam has cross section as shown in figure. 100KN | 100KN 200 mm 25 mm 25 mm 150 um 25 mm 1500 mm 500 mm 500 mm 100 mm
800 N 120 N.m d = 8 cm 600 N Q /If the cross section of the femur can be approximated as a circular tube, determine the state of stresses on the 160 N.m points A and B at section due to the loads as shown in figure. T. = 22 mm n = 18 mm tu Sl'o = I
The 1.5-in diameter solid steel shaft is simply supported at the ends. Two Pulleys are keyed to the shaft where pulley B is of diameter of 4 in and pulley C is of diameter of 8 in. Transverse shear stress needs to be considered. 2) At cross section B, determine the normal stress at points E, F, and G, and the shear stress at point E and F. (cross section B is on the right side of pulley B, and G is the midpoint of EF). y 10 in 200 lbf 1000 lbf B 10 in 500 lbf 100 lbf 10 in Z F G E y
The T-bracket is formed by welding together two cylindrical rods AB and CD. If the allowable shear stress is 80 MPa, what is the smallest allowable diameter of rod AB? Neglect the stress caused by the transverse shear force
Determine the maximum tensile and compressive stresses in portion BC of the beam, under loading conditions of two vertical forces that applied on it. The beam has cross section as shown in figure. 100KN 100KN 200 B 25 m 25 mm 150 m mm -1500 mm 500 mm 500 mm 100 mm
Q1: determine the increase in vertical stresses at depth of Z=3.5 m under points A, B and C due to apply rectangular and ring foundations. The surface load intensity of rectangular is 250 kN/m2, while the surface load intensity of ring is 300 kN/m?.The drawing was done without scale and all dimensions in (m). R1 R2 X1 X2 B L 3 4.5 7.5 12 X1 X2 Aqs-net(2) R1 R2 Aqs-net(1) B B.
State of stress at the wall and the roof of the following circular opening bafore the excavation is (a] = |0 4. Find the induced stress components at point a. R W with respect to the given x-y coordinate systerm, and expresst them in the matrix form. b. Find the total stresses at point W, and give them in matrix form. c. Repeat (a) and (b) for the roof. d. Find the stresses oy, Ciy, and tyy at point A which is located at a radial distance twice the radius of the tunnel.
100 kN and 200 kN to the rectangular column in the figureTwo forces act in intensity. A and B according to givenon the stress element by finding the stresses atshow.