Q1/ In a Hartnell governor, the length of the ball arms is 190 mm, that of the sleeve arms is 140 mm, and the mass of each ball is 2.7Kg. The distance of the pivot of each bell - crank lever from the axis of rotation is 170 mm, and the speed, when the ball arm is vertical, is 300 r.p.m. The speed is to increase 0.6 per cent for a lift of 12 mm of the sleeve. 1- Neglecting the dead load on the sleeve, find the necessary stiffness of the spring and the initial compression. 2- What spring stiffness and initial compression would be required if the speed is to remain the same for the change position of the sleeve.

Q1/ In a Hartnell governor, the length of the ball arms is 190 mm, that of the sleeve arms is 140 mm, and the mass of each ball is 2.7Kg. The distance of the pivot of each bell - crank lever from the axis of rotation is 170 mm, and the speed, when the ball arm is vertical, is 300 r.p.m. The speed is to increase 0.6 per cent for a lift of 12 mm of the sleeve. 1- Neglecting the dead load on the sleeve, find the necessary stiffness of the spring and the initial compression. 2- What spring stiffness and initial compression would be required if the speed is to remain the same for the change position of the sleeve.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shows a mechanism that raises packages in a transfer mechanism. A 500-N package sits on the horizontal output link O4BD while the crank O2A is rotating at constant speed of 400 rpm CW. At the position shown the crank OA is vertical and the output link O4B is horizontal. we need to determine the torque required from the motor at the crank 02A and the force in member AB The weights of the links are negligible. 30mm 450mm 500N 220 mm B 374 mm 374 mm The angular velocity of the link O,BD in rad/s is = The magnitude of the velocity of point D in m/s is =
2. A square threaded screw of mean diameter 25 mm and pitch of thread 6 mm is utilised to lift a weight of 10 kN by a horizontal force applied at the circumference of the screw. Find the magnitude of the [Ans. 966 N] force if the coefficient of friction between the nut and screw is 0.02. A bolt with a squore threaded screw has mean diameter of 25 mm and a nitch of 23 mm It carries an
Required Information Problem 04.007 - Simply supported T-shaped bracket - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A hand truck is used to move a compressed-air cylinder. Assume that the combined weight of the truck and cylinder is 220 lb. 22 in. w Ih 18 in. 10 in. Problem 04.007.c - Determining support reactions of a T-shaped bracket with variable spacing Determine the corresponding reaction at each of the two wheels. The corresponding reaction at each of the two wheels is Ib ICick to select)
A car has hydraulically operated disc brakes at the front and drum brakes at the rear. The frontbrakes have pistons of 58 mm diameter each, whereas each of the wheel cylinder at the rearbrake has 28 mm diameter. The master cylinder piston has diameter of 40 mm. The brake footpedal has a leverage of 4. If the brake pedal is applied a force of 100 N, Calculate (i) The brakingforce on the front axle, (ii) The braking force on the rear axle.
Solve the problem below. For your final answer, use whole number. An extra flexible 8 × 19 steel wire rope of 38 mm diameter is used with a 2 m diameter hoist drum to lift 70 kN of load. The wire rope has a length of 900 meters. The maximum speed is 3 m / s and the acceleration is 1.5 m / s2. The diameter of the wire may be taken as 0.05 d, where d is the diameter of wire rope. The modulus of elasticity of the entire rope is 84 × 103 N/mm2. The weight of the rope is 53 N/m length. Determine the effective load during acceleration of load in kN.
A simple log bridge in a remote area consists of 2 parallel logs with planks across them. The log has an average diameter of 300 mm. A truck moves slowly across the bridge, which spans 2.5 m. Assume that the weight of the truck is equally distributed between the 2 legs. Because the wheel base of the truck is greater than 25 m. Only 1 set of the wheels is on the bridge at a time. Thus, the wheel load on one log is equivalent to a concentrated load acting at any position along the span. In addition, the weight of 1 log and the plank it supports in equivalent to a uniform load of 65 kN/m acting on the log. 1. Determine the max permissible wheel load W based upon the allowable bending stress of of 7MPa. 2. Determine the max permissible wheel load W based upon the allowable shear stress of of 0.75MPa. 3. Determine the max permissible wheel load W based upon the allowable deflection of 6mm. E=7380 MPa
Q1 / A porter govemor has equal links, each 250 mm long pivoted at the axis of rotation, each ball is of mass 4 kg and the mass of the central load is 15 kg. The governor begins to lift when the ball radius is 150 mm. It has a maximum speed at a radius of 200 mm. Determine the maximum speed, the range of speed, the sleeve lift, the governor effort, the power of the governor and governor sensitivity
Required information A photograph of the NASA Apollo 16 Lunar Module (abbreviated by NASA as the LM) is shown on the surface of the Moon. Such spacecraft made six Moon landings during 1969 - 72. A simplified model for one of the four landing gear assemblies of the LM is shown. Assume the weight of the LM is uniformly supported by all four landing gear assemblies, and neglect friction between the landing gear and the surface of the Moon. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A (2.5, 2.5, -2.2) m B (1.5, 1.5,0) m C(2, 1,-1.2) m D(1,2,-1.2) m Z B D If the LM has 14950 kg mass and rests on the surface of the Moon where acceleration due to gravity is 1.62 m/s2, determine the forces supported by members AB, AC, and AD. (Round the final answers to four decimal places. Include a minus sign if necessary.) The forces supported by members AB, AC, and AD are as follows: TAB 10621 N TAC= 2903 N TAD 6032 N
20 deg. Q3: Explane in which case Fa has a maximum Value & minimum Value in Pulling the car shown in Fig 20
Clutch Mechanism 8. In the clutch mechanism shown, two flat circular disks of radius R are mounted so that they can be brought into contact causing a net frictional force. The contact pressure in general depends on the distance from the center and in one specific case may be modeled buy P(r) = Poe-kr, where k is a constant and r is the distance from the center of the discs. The integral cR F = 2m " P(r)rdr gives the total contact force between the discs. Cross-section a. In your own words explain where this formula comes from.
Vrope B. OD f TA ro Vcart Alternate View of Spool (rope not shown) Known values: Ti TA To 0.75 ft 1.2 ft 1.7 ft 1 8 Problem Statement: A large spool rolls without slip on a cart. The cart's speed is 17 ft/s. A rope, which is wrapped around the spool's hub, is being pulled at a speed of 5 ft/s, as depicted. Determine: The angular velocity of the spool: i计 The velocity vector of point G: The velocity vector of point A: i+ Be sure to include units with your answers.
75 lb 10 in. 10 in. | Calculate reaction forces for pin A and roller B for five different values of a 12 im. (0