PROBLEM 3.101 A 4-m-long beam is subjected to a variety of loadings. (a) Replace each loading with an equivalent force- couple system at end A of the beam. (b) Which of the loadings are equivalent? 400 N 200 Nm 400 N 200 N 200 N 800 N 1800 N-m 2300 Nm 800 N 200 N-m 2400 N-m 4000 N-m 600 N 400 N 300 N 3 (A) 900 N-m 200 N 400 N-m 300 N 300 N-m 300 N 300 N·m 800 N 900 N 4500 N-m 300 N-m 200 N

PROBLEM 3.101 A 4-m-long beam is subjected to a variety of loadings. (a) Replace each loading with an equivalent force- couple system at end A of the beam. (b) Which of the loadings are equivalent? 400 N 200 Nm 400 N 200 N 200 N 800 N 1800 N-m 2300 Nm 800 N 200 N-m 2400 N-m 4000 N-m 600 N 400 N 300 N 3 (A) 900 N-m 200 N 400 N-m 300 N 300 N-m 300 N 300 N·m 800 N 900 N 4500 N-m 300 N-m 200 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Version: b Determine the length b of the triangular load and its position a on the beam such that the equivalent resultant force is zero and the resultant couple moment is MR Let M₂ = -30 kN - m R Assume the intensities of the distributed loading be w = 12 kN/m w = 5 kN/m r Let the length of the beam be d = 8 m A b W₁ Wr d Note that the sign of MR indicates whether the couple moment is positive (CCW) or negative (CW). Also, position a may be negative, which indicates that the length of the rectangular load is shorter than the triangular load.
Fj = 375 lb F = 500 lb 4 В. 0.5 ft 8 ft 6 ft 5 ft- 30° F3 = 160 lb II The cantilevered beam above is subjected to an array of forces. Assume that the loading system is to be simplified/summarized by a single resultant force and couple moment acting at point B. Which of the following is closest to the vertical component of the resultant force (i.e. Fry)? a) -220 Ib O b) -140 lb c) 1035 lb d) -914 lb
Detemine the resultant couple moment acting on the plate. Set d= 1.8 m, Fi= 650 N. F2= 250 N and F3= 120 N F1 30 -F: F: 411.3 N.m (CW) 1004 N.m (CW) 1191 N.m (CW) 411.3 N.m (CCW) 1191 N.m (CCW) 1004 N m (CcW
Replace the loading system acts on beam shown in Fig. (3) by an equivalent system consists (Single Force & Couple at point A). 40 N A 30 N B 200 N·m 50 N
Replace the loading system acts on beam shown in Fig. (3) by an equivalent system consists (Single Force & Couple at point A). 40 N 30 N 3m 200 Nom 50 N
Q3/ Shown in fig.( 3 ) replace the loading system by an equivalent resultant force and couple moment acting at point A. 900 N\30° 300 N 300 N-m 0.75 m 0.75 m 0.75 m 0.75 m Fig.( 3 )
The K quadratic prism ОАВСKLMN. if H a=24 m, b=7m, and c=10 m. The prism has F1 width h=14 m. The forces F1=21 N along EP and F2=21 N along HS form a couple Q1, and the forces M F3 F3=12.5 N acts along LB and F4=12.5 N acts A along CK form b а couple Q2 1) x comp. of F1 2) y comp. of F3 3) z comp. of Q1 4) z comp. of Q2 5) y-comp. of the resultant couple 6) magnitude of the resultant couple
Problem 3: Given the cantilever beam show, determine the value of forces N and O if the resultant of the forces will be a downward force of 450N, 9 meters from the right end of the bar. 150N 300N 4in Com 4m
Shaft and flange connections are provided by wedge in a system that transmits moment with flange coupling. The tangential force of the wedge is 40000 N and the diameter of the shaft used in the system is 40 mm and the diameter of the placement circle of the Bolts in the flange connection is 100 mm. Determine how many M16 (d1=13,546 mm) bolts should be used according to the moment transfer by cutting the Bolts between the flange surfaces. (The coefficient of friction between surfaces is 0.25. Bolt material is 4.6 quality and can be taken as Jul-Bolt=40 MPa, σem-Bolt=66.7 MPa. The safety coefficient was determined as 6.)
Problem 7 A Figure shown below. 150 kN A 40 mm Bo 40 mm a. When the applied load of 150 KN is replaced by an equivalent force-couple system with the force acting at point B, Determine the magnitude of the couple? b. When the applied load of 150 KN is replaced by two horizontal forces, one acting at point B and the other acting at point C. Determine the magnitude of the force at B? c. When the applied load of 150 KN is replaced by two horizontal forces, one acting at point B and the other acting at point C. Determine the magnitude of the force at C? ww 08
Question 1 8 kN/m 5 kN/m A 1200 N-m couple moment is applied at B in the direction shown. Find the support reactions at 0. Ok. 4 LN - Oya i8.4 xN ↑ M.• 26.3 kN m G 1.5 m -0.75 m 0.75 m 4 5 kN
As shown, a submarine hatch door is to be opened by applying two oppositely oriented forces of equal magnitude F = 310 N at points A and B on the hatch door wheel. The radii of the wheel's inner and outer rings are r1 = 0.500 m and r2 = 0.130 m , respectively. (Figure 1) Calculate the moments MA and MB about point D for the forces applied at points A and B. Then, determine the resulting couple moment MR. Assume that a positive moment produces a counterclockwise rotation whereas a negative moment produces a clockwise rotation.