plat system IS sugge the thickness of plate. 1 is 12 mm and plate. 2 is 10 mm. The yield stres modulus of Elasticity for plate,1 is 300 MPa, and 200 GPa respectively, whil plate, 2 is 400 MPa and 210 GPa respectively. Assume the tensile stress is equ the compressive stress for both plates. Calculate the efficiency of riveting syst

plat system IS sugge the thickness of plate. 1 is 12 mm and plate. 2 is 10 mm. The yield stres modulus of Elasticity for plate,1 is 300 MPa, and 200 GPa respectively, whil plate, 2 is 400 MPa and 210 GPa respectively. Assume the tensile stress is equ the compressive stress for both plates. Calculate the efficiency of riveting syst

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.12P: Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in...

See similar textbooks

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
Consider the copper lubes joined in the strength of the copper is err = 200 MPa, figure using a "sweated" joint. Use the properties and what is the maximum load P]iwathat can be dimensions given. applied to the joint if the desired factor of safety in shear is FS_ - 2 and in tension is (a) Find the total elongation of segment 2-3-4 (
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
At a point in a bar of cast iron, the principal stresses are 60 MPa tensile and 120 MPa compressive whereas the third principal stress is zero. Find the factorsof safety based on the elastic limit when the criterion of failure is principal stress theory. Assume the elasticlimit of cast iron is 90 MPa in tension and 440 MPa in compression
Q1. A plate b mm wide and t mm thick is joined with another plate by a single transverse and a double parallel fillet weld as shown in Fig. if the permissible tensile and shear stresses in the weld material are otw MPa and tw MPa respectively and the permissible tensile stress in the plate material are otp MPa, Find the length Li of single transverse fillet weld, if the joint is subjected to both static and fatigue loading. All dimensions in mm.
100 kN A bracket in the form of a plate is fitted to a column by means of four rivets of the same size, as shown in Fig. A load of 100 kN is applied to the bracket at an angle of 60° to the horizontal and the line of action of the load passes through the centre of the bot- tom rivet. If the maximum shear stress for the material of the rivet is 70 MPa, find the diameter of rivets. What will be the thickness of the plate if the crushing stress is 100 MPa? 80 80 80 60° All dimensions in mm.
4. A ring made of 2-5 cm diameter steel bar carries a pull of 10 kN. Calculate the maximum tensile and compressive stresses in the material of the ring. The mean radius of the ring in 15 cm.
A tube from aluminium with an outside diameter of 50 (mm) and a wall thickness of 5 (mm) is used as a compression member. If the axial normal stress in the member must be limited to 90 MPa, what is the maximum force (in kN) that the member can support.
A plate 70mm wide and 15mm thick is joined with another plate by a single transverse weld and a double parallel fillet weld. The maximum tensile and shear stresses are 60MPa and 50MPa respectively. Find the length of each parallel fillet weld, if the joint is subjected to static loading.
Q 2: A circular rod of 15 mm diameter and 120 mm length, is subjected to 2.5 RN tensile load if the diameter become 12 mm find 1. True stress. 2. The length of the rod after deformation.