Write PLC to execute this. • Normally open start and normally closed stop pushbuttons are used to start and stop the process.• When the start button is pressed, solenoid A energizes to start filling the tank.• As the tank fills, the empty level sensor switch closes.• When the tank is full, the full level sensor switch closes.• Solenoid A is de-energized.• The agitate motor starts automatically and runs for 3 min to mix the liquid.• When the agitate motor stops, solenoid B is energized to empty the tank.• When the tank is completely empty, the empty sensor switch opens to de-energize solenoid B.• The start button is pressed to repeat the sequence.SOL AMotorFullsensorswitchEmptysensorswitch- SOL BStart/stopcontrol stationAllocations:SymbolAddressField DeviceESTOP10.0N.C. momentary contact pushbuttonSTART10.1N.O. momentary contact pushbuttonEMPTY10.2N.O. Level sensorFULL10.3N.O. Level sensorMOTORQ0.0Motor starterSOL_AQ0.1Solenoid valveSOL_BQ0.2Solenoid valve

Given: • Normally open start and normally closed stop pushbuttons are used to start and stop the…

Answered: • Normally open start and normally…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter3: Magnetic Starters

Section: Chapter Questions

Problem 16SQ

See similar textbooks

Similar questions

1. In an automatic mixing operation the sequence of operation is as follows: When the start button is pressed fill the tank with Liquid B till it reaches X1 and then fill the tank with Liquid A till it reaches X2. Once the level of Liquid reaches X2, turn on the motor for another 20 seconds for mixing process. After the timer stops timing, empty the tank by opening the mixture outlet. X1 and X2 are capacitive proximity sensors and there are start, stop and emergency stop push buttons. XO START X1 STOP YO (Liquid A Inlet ) EMERGENCY STOP YI(Liquid B Inlet) Y2(Mixture Outlet) For the system explained above answer the following: a) Provide the Allocation List b) Draw the Grace and extract the grafcet equation c) Draw the Ladder Diagram
Fill in the blanks: Given the model for position control system, find the value for K1 and K2 so that the peak time is equal to 0.5 s and the %OS is equal to 3%. K1= 93.2070 K2= 0.129 I 446 23
What are the functions of a Transfer Switch: (Select all answers that apply) Group of answer choices A. Shifts electrical power from the normal utility power source to the standby power source B. Isolates the utility source from the standby source in such a way that there is no feedback from the generator to the utility’s system or vice versa C. When normal power is restored, the automatic transfer switch resets itself and is ready for the next power outage D. Provides for measuring of power usage by the residents during periods of brownouts with the generator offline.
1. In a second-order linear process control system the pressure value changes from 0 to 50 PSI values in 4 seconds with a transient period ends at 3 seconds. If the maximum overshoot in this pressure control system is 10%, Find out the peak pressure value that the system was reached to? Answer: 55 Assume that the system in the above question has a rise time of 2 seconds, Also assume that the pressure value at 0.5 sec is 5PSI. What is the pressure value of the system in PSI at 2.5 seconds? Answer: 45 The answer is given. Work for step by step solution to get the given answer.
The following are some primary factors that contribute to cavitation damage EXCEPT А. Pressure difference Location C. Material used D. O Valve size B.
In the simple lamp dimmer shown here, what method of power control is being used? AC supply Triac Select the correct response. burst firing proportional control feedback control phase control
A switch that can conduct positive on-state current, and can block positive or negative off-state voltage is called ___. A. voltage-bidirectional two-quadrant switch B. synchronous rectifier C. single quadrant switch D. four-quadrant switch
Technician A says when testing the voltage output, if the charging voltage is too high, the cause could be an open field wire from the regulator. Technician B says a loose or glazed drive belt could be the cause of too high charging voltage. Who is correct? A only B only Both A and B Neither A or B Technician A says that poor connection at the generator output wire can cause charging systems problems. Technician B says that many charging system circuits contain a circuit protection device. Who is correct? A only B only Both A and B Neither A or B
Determine the value of R1 that will ensure proper turn-on and turn-off for the following values: eta = 0.33, valley voltage at 0.8V, valley current at 15 mA, peak current at 35 micro Amperes, and peak voltage at 18V.
alculate the maximum force that should be applied via a pulling eye to a 70 mm2, 3-core copper cable,lf this is a low voltage cable with a PVC sheath, what is the maximum length of PVC pipe it can be pulled through?
From our experiment we used LM555 timer to demonstrate a multivibrator circuit. The following choices are a PIN number and its function of LM555 timer, which one is not correct? PIN 2 - Trigger PIN 7 - Discharge PIN 6 - Threshold PIN 4 - Control Voltage
A press's machine cycle is as follows: Lowering the ram: the ram is lowered when 0 The safety screen was open before the cycle began and is now closed (limit switches S4 and S5 actuated) The press is in the home, i.e. upper position (limit switch S6 actuated) Two-hand switches S1 and S2 were not actuated prior to the cycle but are now Halting the ram during lowering: the ram stops 0 ;immediately when One of the two-hand switches is released. Or . The safety screen is opened. Or . .The ram is down (limit switch S3 actuated) Raising the ram: If the ram is down (limit switch S3 actuated), it is raised by the eccentric drive. The safety .screen can be opened and both two-hand switches released The machining cycle is completed when the ram reaches the home position (limit switch S6 actuated) The designer needs for ........conditional output boxes for drawing the ASM-chart for the controller of the aforementioned system 0 C 2 3 O O O O O O

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS