1. In an automatic mixing operation the sequence of operation is as follows: When the start button is pressed fill the tank with Liquid B till it reaches X1 and then fill the tank with Liquid A till it reaches X2. Once the level of Liquid reaches X2, turn on the motor for another 20 seconds for mixing process. After the timer stops timing, empty the tank by opening the mixture outlet. X1 and X2 are capacitive proximity sensors and there are start, stop and emergency stop push buttons. XO START X1 STOP YO (Liquid A Inlet ) EMERGENCY STOP YI(Liquid B Inlet) Y2(Mixture Outlet) For the system explained above answer the following: a) Provide the Allocation List b) Draw the Grace and extract the grafcet equation c) Draw the Ladder Diagram

1. In an automatic mixing operation the sequence of operation is as follows: When the start button is pressed fill the tank with Liquid B till it reaches X1 and then fill the tank with Liquid A till it reaches X2. Once the level of Liquid reaches X2, turn on the motor for another 20 seconds for mixing process. After the timer stops timing, empty the tank by opening the mixture outlet. X1 and X2 are capacitive proximity sensors and there are start, stop and emergency stop push buttons. XO START X1 STOP YO (Liquid A Inlet ) EMERGENCY STOP YI(Liquid B Inlet) Y2(Mixture Outlet) For the system explained above answer the following: a) Provide the Allocation List b) Draw the Grace and extract the grafcet equation c) Draw the Ladder Diagram

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter13: Heating Control Devices

Section: Chapter Questions

Problem 6RQ

See similar textbooks

Similar questions

What is the most important load in a refrigeration system
1. In a second-order linear process control system the pressure value changes from 0 to 50 PSI values in 4 seconds with a transient period ends at 3 seconds. If the maximum overshoot in this pressure control system is 10%, Find out the peak pressure value that the system was reached to? Answer: 55 Assume that the system in the above question has a rise time of 2 seconds, Also assume that the pressure value at 0.5 sec is 5PSI. What is the pressure value of the system in PSI at 2.5 seconds? Answer: 45 The answer is given. Work for step by step solution to get the given answer.
Q2. Answer two branch only A) Draw the Full-wave rectifier ammeter circuit with Step up transformer? B)Draw the PMMC scheme showing the deflecting and controlling forces? C)Draw the current flowing left to right producing positive deflecting torque?
A switch that can conduct positive on-state current, and can block positive or negative off-state voltage is called ___. A. voltage-bidirectional two-quadrant switch B. synchronous rectifier C. single quadrant switch D. four-quadrant switch
Question: In a single phase semiconverter if the output voltage has peak and average values of 325 V and 133 V respectively then the firing angle is Option 1: 43.40° Option 2: 53.40° Option 3: 73.40° Option 4: 33.30°
is the amount of change in the controlled variable required to run the controlled device from one extreme to the 10. other a- Offset b- Throttling range 11. used to reduce overshoot when a rapid response is desired a- Derivative control b- Proportional control 12. RTDS have a a- Positive temperature coefficient b- Negative temperature coefficient 13. Thermistors have a- Positive temperature coefficient b- Negative temperature coefficient 14. Open loop control is a system with a- No feedback b- with feedback 15. W a- Floating controller b- Potentiometer type controller O this figure refer to R
Create a Sequence Diagram about Temperature Controlled Electric Fan with the following: *Thermistor *Microcontroller *Motor Driver *Motor
Draw the block diagram of ventricular synchronous demand pacemaker.
A step up chopper has an input of 200 volts and output of 250 volts. The blocking period is each cycle is 0.6x10-3 seconds. Find the period of conduction in each cycle and frequency of operation?
Unit step function input to the system in the figure and proportional What are the values of the following transient response specifications when the control (K = 50) is applied? a. It's time to rise b. Time to reach the maximum, c. maximum exceed D. Settling time (by 2% criterion).
State whether the following statement is true or false. “The efficiency of a switching regulator is always higher than that of a linear regulator.” Please explain.
ASYNCIN Dan Synchronous System CLOCK Figure Q4 (b) The circuit in Figure Q4 (c) consists of edge triggered flipflops. The second flipflop receives the clock signal through a long slow path which results in delay. Answer the following questions: Q1 Q2 IN DaK CLOCKD CLK CLOCK A long, slow path Figure Q4 (c) 林 Define clock skew, Explain with a timing diagram, what problem this circuit might face? What condition it must satisfy to ensure that the intended circuit output is not affected? For the following LFSR circuit in the Figure Q4 (d), let the initial entries of stages R, be S, for 0sisn. Compute the first 12 bit output for the following cases of initial entries: (d) S2 Si So Case 1 Study Pack Practice &A Case 2