MLT The resistin, .orce (F) of a supersonic plane during flight can be considered as dependent upon the length of the air craft (L), Velocity (u), air dynamic viscosity (u), air density (p), and bulk modulus of elasticity of air (ɛ). Express, by dimensional analysis, the functional relationship between these variables and the resisting force.

MLT The resistin, .orce (F) of a supersonic plane during flight can be considered as dependent upon the length of the air craft (L), Velocity (u), air dynamic viscosity (u), air density (p), and bulk modulus of elasticity of air (ɛ). Express, by dimensional analysis, the functional relationship between these variables and the resisting force.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.9P: When a sphere falls freely through a homogeneous fluid, it reaches a terminal velocity at which the...

See similar textbooks

Similar questions

MLT By dimensional analysis, obtain an expression for the drag force (F) on a partially submerged body moving with a relative velocity (u) in a fluid; the other variables being the linear dimension (L), surface roughness (e), fluid density (p), and gravitational acceleration (g).
The drag coefficient in aircraft industry affected by some parameters which are thespeed of plane (v), the plane length (L), the air density (ρ), the air dynamic viscosity(μ), and speed of sound (a). By using dimensional analysis, identify two non-dimensionnumbers in which the drag coefficient is a function of them and explain how these twowill effect on drag coefficient.
The thrust force of propeller (P) depends upon the flow velocity V, angular velocity o, diameter D, dynamic viscosity , density p. the speed of sound in the medium C. (1) Derive the relationship between the above variables and the thrust force by using Buckingham's IT-theorem. (2) Explain the physical meaning of the obtained dimensionless groups. إجابت
Q1) Under laminar conditions, the volume flow rate Q through a small triangular-section pore of side length (b) and length (L) is a function of viscosity (u), pressure drop per unit length (AP/L), and (b). Using dimensional analysis to rewrite this relation. How does the volume flow changes if the pore size (b) is doubled?
The power P generated by a certain windmill design dependson its diameter D , the air density ρ , the wind velocity V , therotation rate Ω , and the number of blades n . ( a ) Write this relationship in dimensionless form. A model windmill, of diameter50 cm, develops 2.7 kW at sea level when V = 40 m/s andwhen rotating at 4800 r/min. ( b ) What power will be developedby a geometrically and dynamically similar prototype, ofdiameter 5 m, in winds of 12 m/s at 2000 m standard altitude?( c ) What is the appropriate rotation rate of the prototype?
An automobile has a characteristic length and area of 8 ft and 60 ft, respectively. When tested in sea-level standard air, it has the following measured drag force versus speed: V, mi/h 20 | 40 60 Drag, Ibf 31 115 249 The same car travels in Colorado at 65 mi/h at an altitude of 3500 m. Using dimensional analysis, estimate (a) its drag force and (b) the horsepower required to overcome air drag.
The drag force (Fdrag) exerted by air on a moving car depends on a dimensionless drag coefficient (Carag), the specific volume of air (Vair), the velocity of the car (Var), and the frontal area of the car (Afront). (a) Based on unit considerations alone, obtain an equation for the drag force. Be sure to explicitly demonstrate that the final units are correct. (b) Explain, based on your equation, what happens to the drag force when each variable is changed in isolation. Indicate whether this predicted behaviour matches your intuition in each case.
By dimensional analysis, obtain an expression for the drag force (F) on a partially submerged body moving with a relative velocity (u) in a fluid; the other variables being the linear dimension (L), surface roughness (e), fluid density (p), and gravitational acceleration (g).
Dimensional analysis is to be used to correlate data on bubble size with the properties of the liquid when gas bubbles are formed by a gas issuing from a small orifice below the liquid surface. Assume that the significant variables are bubble diameter D, orifice diameter d, liquid density rho, surface tension sigma (in N/m), liquid viscosity mu, and g. Select d, rho, and g as the core variables.
Dimensional analysis can be used in problems other than áuid mechanics ones. The important variablesaffecting the period of a vibrating beam (usually designated as T and with dimensions of time) are the beamlength `, area moment of inertia I, modulus of elasticity E, material density , and Poissonís ratio , so thatT = f cn(`; I; E; ; )Recall that the modulus of elasticity has typical units of N/m2 and Poissonís ratio is dimensionless.(a) Find dimensionless version of the functional relationship.(b) If E and I must always appear together (meaning that EI is e§ectively a single variable), Önd a dimensionless version of the functional relationship.
In the field of air pollution control, one often needs to sample the quality of a moving airstream. In such measurements a sampling probe is aligned with the flow as sketched in Fig. A suction pump draws air through the probe at volume flow rate V· as sketched. For accurate sampling, the air speed through the probe should be the same as that of the airstream (isokinetic sampling). However, if the applied suction is too large, as sketched in Fig, the air speed through the probe is greater than that of the airstream (super iso kinetic sampling). For simplicity consider a two-dimensional case in which the sampling probe height is h = 4.58 mm and its width is W = 39.5 mm. The values of the stream function corresponding to the lower and upper dividing streamlines are ?l = 0.093 m2/s and ?u = 0.150 m2/s, respectively. Calculate the volume flow rate through the probe (in units of m3/s) and the average speed of the air sucked through the probe.
The power P generated by a certain windmill design depends upon its diameter D, the air density p, the wind velocity V, the rotation rate 0, and the number of blades n. (a) Write this relationship in dimensionless form. A model windmill, of diameter 50 cm, develops 2.7 kW at sea level when V= 40 m/s and when rotating at 4800 r/min. (b) What power will be developed by a geometrically and dynamically similar prototype, of diameter 5 m, in winds of 12 m/s at 2000 m standard altitude? (c) What is the appropriate rotation rate of the prototype?