Material A (shown below) is experiencing forces shown below at different points along its body. If the area of its cross section is equal to 0.355 in^2, determine the total new length of the material if modulus of elasticity is equal to 15x10^6 psi. AB = 3.4 ft BC = 4.85 ft, CD 3.58 ft. %3D 6000 lb 7000 lb 5000 lb 4000 lb

Material A (shown below) is experiencing forces shown below at different points along its body. If the area of its cross section is equal to 0.355 in^2, determine the total new length of the material if modulus of elasticity is equal to 15x10^6 psi. AB = 3.4 ft BC = 4.85 ft, CD 3.58 ft. %3D 6000 lb 7000 lb 5000 lb 4000 lb

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. A steel wire 2 m long and 3 mm in diameter is extended by 0.75 mm when a weight W is suspended from the wire. If the same weight is suspended from a brass wire, 2.5 m long and 2 mm in diameter, it is elongated by 4.64 mm. Determine the modulus of elasticity of brass if that of steel be 2.0 x 10° Nhmm².
Material A (shown below) is experiencing forces shown below at different points along its body. If the area of its cross section is equal to 0.485 in^2, determine the total new length of the material if modulus of elasticity is equal to 12.5x10^6 psi. AB = 3.58 ft BC = 5 ft, CD = 3.95 ft. %3D %3D %3D 6000 lb 7000 lb 5000 lb 4000 lb A O 12.5353 ft O 12.5385 ft O 12.5342 ft O 12.5364 ft O 12.5321ft O 12.5366 ft O 12.5378 ft
Problem #3 The bar shown below has uniform cross section and material properties throughout. In addition to the loads shown, the bar experiences a uniform temperature change of AT. Given the x displacement at B is equal to -0.3022409955 inches determine the change in temperature, AT. Report your answer in degrees F to 2 decimal places. D x 8 ft C 10 kip 5 ft B 30 kip 3 ft A 30 kip E = 18,000 ksi a = 8.0 x 10-6 1/°F A 0.15 in²
PROBLEM 3: A material has a modulus of elasticity of 200 GPa. Find the minimum cross sectional area of the said material so as not to elongate by more than 3 mm for every 2m length when subjected to a 12 kN tensile force. a. 20 mm? c. 30 mm? b. 10 mm? d. 40 mm?
4. A steel wire 2 m long and 3 mm in diameter is extended by 0.75 mm when a weight W is suspended from the wire. If the same weight is suspended from a brass wire, 2.5 m long and 2 mm in diameter, it is elongated by 4.64 mm. Determine the modulus of elasticity of brass if that of steel be 2.0 x 10° Nhmn.
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 404 mm2, 642 mm2 , and 271 mm2 respectively.Determine the change in length (in mm) of the bar if P = 28943 N.The moduli of elasticity are 80.75 GPa for bronze ,73.14 GPafor aluminum , and 203.66 GPa for steel . Round off the final answer to four decimal places.
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 416 mm?, 622 mm?, and 281 mm? respectively.Determine the change in length (in mm) of the bar if P = 27177 N.The moduli of elasticity are 81.33 GPa for bronze ,73.05 GPafor aluminum , and 200.23 GPa for steel . Round off the final answer to four decimal places. Bronze Aluminum ЗР Steel 2P P 4P -0.6 m 1.0 m- 0.8 m
As seen in the figure, a rigid beam carried by three elastic rods of equal length from points A, B, and C is pulled to Eve from points F by P-force. The modulus of elasticity of the bars are E1=100GPa, E2=120GPa and E3=100GPa. Yield stress σA=40 MPa for bar 1 and 3, yield stress σA=120 MPa for bar number 2. Accordingly, a) determine the load PA that will start the flow, b) the load PG that will cause the migration.
The figure shows the infinitely rigid bar (ACD) suspended by three steel wires of diameter ? and elasticity ?, whose maximum allowable stress in the elastic range is ??. On the bar, weighing ?, it also exerts a point force ? as indicated in the figure. ?= 10 [kN], ?=5 [kN], ?=5 [mm], ?=1 [m], ?=50 [cm], ?=190 [GPa] , ??= 200 [MPa]. a) Calculate the vertical reactions on each of the wires.If applicable, indicate what wires are at risk of collapse b) Calculate the deformations of each wire for the case shown in a) c) Calculate the maximum deformations in each wire so that their behavior remains in the elastic range
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 415 mm?, 636 mm² , and 253 mm² respectively.Determine the change in length (in mm) of the bar if P = 28084 N.The moduli of elasticity are 83.77 GPa for bronze ,71.95 GPafor aluminum , and 204.98 GPa for steel. Round off the final answer to four decimal places. Bronze Aluminum Steel 2P ЗР P. 4P 0.6 m →k 1.0 m 0.8 m Add your answer
Problem 2.5. A metallic bar 300 mm x 100 mm x 40 mm is subjected to a force of 5 kN (tensile), 6 kN (tensile) and 4 kN (tensile) along x, y and z directions respectively. Determine the change in the volume of the block. Take E = 2 x105 N/mm² and Poisson's ratio = 0.25.
The reinforced concrete considered in the figure below is subject to pure bending without any axial force. Compute the bending stress in the extreme fiber of the beam of figure for bending moment 0.9ton.m . E, = 2*10ʻ kg / cm E = 222940kg /cm? f' = 225kg / cm F, = 4000kg / cm? 2 2 15 cm 20 cm 2#16 20 cm