In the Figure 5, the normal stress on the cross-sectional area is (in Mpa):Figure 5:yP = 400 KNX30 mm1000 mm30°Area20 mmالاختيارات577597587567OOO

Area = A = 20 X 30 = 600 mm2 Force normal to area Pn = 400 cos (30) Pn = 346.41 KN

Answered: In the Figure 5, the normal stress on…

In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: y P = 400 KN 1000 mm 30° Area 30 mm 20 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.27P: -27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile...

See similar textbooks

Related questions

Q: ind the position and the value of the maximum stress for the weld joint shown in the figure. Assume…

A: Given Force, F = 50 kN Length of weld, L = 60 mm Find Shear stress

Q: 4. The magnitude of aa1, the angle F1 makes with the x-axis, is nearest a) 35⁰ b) 50° c) 71° d) 66°…

Q: Bernoulli equation deals with the law of conservation of a) mass (b) momentum (c) energy (d) work…

A: Daniel Bernoulli is the main person behind Bernoill's principle which tells that as moving fluids…

Q: In the Figure 5, the equilibrium shear force component at the fixed edge of the cantilever beam is…

Q: a projectile is fired with an initial velocity of 120 m/s off the roof of the building. Determine…

Q: Q2:B) Calculate the power required to pull (1.5m x 1.5m) flat plate at speed (1 m/s) to the left…

A: Given data Dimensions of plate = 1.5 m x 1.5 m Speed of flat plate = 1 m/s Horizontal spacing = t =…

Q: Decide whether each of these statements is TRUE (T) or FALSE (F). For the part of the ladder program…

A: In delay-off timer, after input stops there is a delay of 5 s then output stops.

Q: 8) A 5.9866 cm-diameter water jet with V₁-45 m/s, strikes a moving blade with Vb-15 m/s. The power…

Q: Q1 -A- A man stands on the middle rung of a 250 N ladder resting on a smooth floor and against a…

Q: A- The power produced from a pump (P) is fun (Hon of flow (@), pressure drop (P), Density of fluid…

Q: Q6-Determine the maximum force P that can be applied without causing movement of the 90-kg crate…

Q: (a) We can determine the amount of heat transfer for any system undergoing any process using a…

A: We can determine the amount of heat transfer for any system undergoing any process using a…

Q: An articulated robot loads and unloads a CNC machine tool. The cell is scheduled to produce a batch…

A: Given data: the number of parts in a batch (n) = 300 programmed machining time per cycle (tm) = 3.75…

Q: The ring shown is subjected to two forces F1 and F2. If it is required that the resultant force have…

Q: Iron Ore are mainly used to produce high heat in blast furnace Select one: True False CamScanner

A: Iron ore are mainly used to produce high heat in blast furnace.

Q: Q2 At a given instant, the gear has the angular motion shown. At this instant, Determine: 1- The…

Q: 26. Explain the principles of DC motors, including the DC permanent magnet motor and how it can have…

A: Definition of DC motors: DC motors are electirical device that converts the given electrical energy…

Q: Find the position and the value of the maximum stress for the weld joint shown in the figure. Assume…

A: Given Force, F = 50 kN Length of weld, L = 60 mm Find Shear stress

Q: The control lever is subjected to a clockwise couple of 112 N-m exerted by its shaft at A and is…

A: Given data: MA=112 N.mF=300 Na=145 mmθ=24° Need to determine the dimension (x) of the lever.

Q: 14. The operational amplifier circuit shown in the following figure includes a thermistor. V+ 6 100…

A: As per the Bartleby answering guidelines we are supposed to answer only first Question.please repost…

Q: Discuss the difference between Alloys and composite materials

A: The difference between alloys and composite materials are followings:

Q: Q3 - Determine the reactions at A and B. in the Figure 7. Fig. (7) 9 KN 20 kN \T 5 kN/m 2 m 1.5 m 1m…

Q: This is the answer plz write white page Given, RA= 1300N RB-433N = 50N Assume mass of man = M Fx=0…

Q: Q3: In a mechanical application a composite part is required to have the properties, the…

A: Given Data The longitudinal modulus of elasticity is:Ec1required=105 GPa The transverse modulus of…

Q: Q2: A composite material has a cross-sectional area of 1150 mm². The fibers carried a stress of 200…

A: Given data: Cross-sectional area of composite = 1150 mm2Stress carried by fiber = 200 MPaForce…

Q: Q2-A- Use the graphical method to find the magnitude and direction of the resultant of these forces.…

Q: A lifting platform is to lift a load of 20KN and is to have a system pressure of 10 bar. How large…

Q: Two blocks A and B of weight 350 N and 600 N, respectively are connected by a cord that passes over…

Q: A) List the devises that used to measure the velocity, pressure, volume flow rate and sketch each of…

A: subject : fluid mechanics

Q: Situation 4: A mercury barometer at the base of a mountain reads 736mm at the same time, another…

A: Atmospheric Pressure: The pressure exerted by atmospheric air normally upon all surfaces with which…

Q: 1- A stationary gas-turbine power plant operates on a simple ideal Brayton cycle with air as the…

A: Disclaimer: “Since you have asked multiple questions, we will solve the first question for you. If…

Q: Consider the following chemical mixing example Fig. below. Two process streams are mixed to produce…

A: 1) as in combustion problem where oxygen and fuel is mixed and spark(heated ) to obtain heat energy…

Q: Thermodynamics problem. For a specific volume of vT = xvg+(1-x)vf = 0.2m3/kg, find the vapor…

Q: Q1 -A- A man stands on the middle rung of a 250 N ladder resting on a smooth floor and against a…

Q: Q1: E-glass fibers reinforced epoxy matrix to fabricate a composite part. The volume fraction of…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Derive the expression for the braking torque

Q: Air flow though the device shown in figure. Select which set of the following conditions is TRUE…

A: Option : (e) is correct At point 1& 4 At point 1 cross section area of device is less as…

Q: Q2-A- Use the graphical method to find the magnitude and direction of the resultant of these forces.…

A: Given

Q: Q2:B) Calculate the power required to pull (1.5m x 1.5m) flat plate at speed (1 m/s) to the left…

Q: A) devises used to me volume flow rate and sketch each of them with equations. the velocity,…

Q: Q2/ The 300N force is resultant of two forces, one of the force (T) has the direction along tine AB…

Q: A steam turbine receives 362500 kg/h of steam throttled at 8.70 Mpa and 410C. Steam leaves the high…

A: Given data, Mass flow rate of the steam, m˙s= 362500 kg/h m˙s=3625003600m˙s=100.69 kg/s Pressure at…

Q: Products produced by precision forging require

A: we have to discuss about the precision forging operation

Q: B) A rectangular gate (length 3m, wide 1m) inclined at 50⁰ with the horizontal level and hinged at…

A: Length of the gate, L==3 mWidth of the gate, w=1 mInclination angle between the gate and horizontal…

Q: Given, RA= 1300N - RB 433N T = 50N Assume mass of man = M D T A₁ ≤ A12m Tsin30 EF=0 RA Tcos30-RB = 0…

Q: Q1. Design a cast iron flange coupling for a mild steel shaft transmitting 90 kW at 250 r.p.m. The…

Q: The L-frame in figure below supports forces from two cables. Cable “EAD” passes through a…

Q: Out of 100% energy injected into steam boiler, how many percentage goes into flue gas waste? a. 28%…

Q: Please answer f,g,h, and i as well. I need this now. I posted this as separate but was answered same…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A materials engineer wants to understand the relationship between the strength of plastic cases and…

A: Explanatory Variable is a factor or parameter that has been changed in an experiment by a researcher…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

In the Figure 5, the normal stress on the cross-
sectional area is (in Mpa):
Figure 5:
y
P = 400 KN
X
30 mm
1000 mm
30°
Area
20 mm
الاختيارات
577
597
587
567
O
O
O

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2- Show the stress components of a point in plane stress on the square in Figures below: Ty = 18 ksi Oy = 85 ksi (T) = 27 ksi (C) Oxx 1- 18 ksi %3D = 100 MPa (T) =-75 MPa 2- = -75 MPa = 85 MPa (T)
Bi-axial state of stress at a point is shown below. What will be the value of principal stresses and maximum in-plane shear stress. 80 MPa 50 MPa 100 MPa * 100 MPa 80 MPa
the state of stress at a point can be described by óx=36 MPa and Txy= 17MPa a second coordinate system is rotated by theta35 degrees What is the normal stress in the direction of the x' axis what is the shear stress in the y'-direction for the faces with a normal in the x'-direction what is the normal stress in the direction of the y'-axis
The state of plane stress at a point is represented on the element shown in the figure. The element oriented 40° 'counterclockwise. Find the value of ox 30 MPa 20 MPa -10 MPa +55.2 Mpa +11.4 Mpa -37.9 Mpa +24.7 Mpa -11.4 Mpa +37.9 Mpa -55.2 Mpa -24.7 Mpa +45.9 Mpa -45.9 Mpa
The state of plane stress at a point is represented by the element shown in the figure. Oy o, = 200 Mpa oy = 450 Mpa Txy Try 3D200 Мра Click here to see all formulas Ox Part A - Determine the maximum principal stress in Mpa. O 253 О 355 O 507 O 760 O 608 Submit Request Answer O O O O O
The state of plane stress at a point is represented on the element shown in the figure below. (a) Determine the principal stresses acting on this point, and the corresponding orientation (angle). (b) Determine the maximum in-plane shear stress, and the corresponding orientation (angle). Also determine the associated average normal stress. Draw Mohr's circle and show the stresses on the circle. 16 MPa 10 MPа
b3 C Q ↑ D P= 23 KN R = 34 KN Square Bars b₁ = 57 mm 6₂ = 19mm b3 = 38mm WHAT IS THE AXAIL STRESS IN BAR 1 ? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS. (1) A Guen: b₁ B (2) Q =9 kN b₂ (3) R
Q1. For the given cube below, complete the following: 1.find the center, radius (R), principal normal stresses (σ and σ3), max shear stress (Tmax) and draw the Mohr's Circle. 2. Find the stresses on a plane that is rotated 60° clockwise from the horizontal plane. 6PSE IPSF 10pst 60⁰ TOPST IPSF 6PSF
Illistrate Mohr's circle for the given plane stress state. Including the coordinates of the points, show the points with the faces of the figure, the center of the circle and the magnitude of the radius. 7. 3kPa 5kPa 1kPa
160 MPa Find the approximate prime plane in degrees for the state of stress given in the figure. 45 MPa 100 MPa 100MPa 45 MPa 60 MPa O 66 O 55 O 44 O 33 O 2
Problem 3: For the plane stress state listed below, draw a Mohr's circle diagram properly labeled. Keep in mind that the principal stress is that stress state where the shear stress is zero. That means it is the stress state along the normal stress line in Mohr's space. So, use your Mohr's circle to find the principal normal and shear stresses, and determine the angle from the x axis to o1. 0x = 16 kpsi, oy = 9 kpsi, Ty = 5 kpsi ccw
In a volume element with dimensions dx, dy, dz the negatíve y-face has a 2 MPa stress in the positivex-direction, a 3 MPa stress in the negative z-direction, and a 4 MPa stress in the negatíve y-direction. Which of the following describes the stresses per elasticity convention? Oyy = 4 MPa Oyr = -2 MPa 3 MPa A MPa