Answered: Out of 100% energy injected into steam…

Out of 100% energy injected into steam boiler, how many percentage goes into flue gas waste? a. 28% b. 33% c. 15% d. 20%

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter31: Gas Heat

Section: Chapter Questions

Problem 61RQ: A _____________sample is taken from the flue gas tocheck the efficiency of a gas furnace.

See similar textbooks

Related questions

Q: A R₁ Find R1 and R2 reactions in kg. 1000 kg. 400 kg BY 3m 1.5m 6m C D 1.5m R₂

A: All forces are measured in kg rather than N, as mentioned in the question. As given in question,…

Q: A flat belt is required to transmit 35 kW from a pulley of 1.5 m effective diameter running at 300…

A: Belt drives are a sort of frictional drive that transmits power from one shaft to another through…

Q: 4- Calculate temperatures for nodes 1 to 6 which is the steady-state. h = 12 W/m² °C T₁ = 15°C

A: T=50°C∆x=∆y=25cmk=1.5W/m°Ch=12W/m2CT∞=15°C To-Find:- Temperatures for nodes 1 to 6 at steady-state…

Q: For 13 to 15. The compound bar carries the axial forces P and 2P. The working stresses are 40 ksi…

A: For solution refer below images.

Q: 1.5A 20 N 2m G Find Ox, Oy, Txy in Point A if the dignete = 30m² ох,

Q: Q2: A two-stroke diesel engine was electrically motored (non-firing operation) when the me reading…

A: Given Brake torque, T = 120 N.m Speed, N = 600 rpm Calorific value, CV = 40.3…

Q: Q4. A flanged protective type coupling is required to transmit 50 kW at 2000 r.p.m.. Find: (a) Shaft…

A: Given data: P=50 kWN=2000 rpm Need to determine the diameter of the shaft, diameter of bolts, pitch…

Q: The shaft of a mechanical device is designed to transmit the torque T = 100 N. m. The shaft could be…

Q: The mass center G of the 1405-kg rear-engine car is located as shown in the figure. Determine the…

Q: The rigid bars AB and CD shown in Fig. are supported by pins at A and C and the two rods. Determine…

Q: 4.2 Test results obtained on a NACA 23012 airfoil show the following data: a⁰ C₁ 0 0.15 9 1.20 If…

A: Given: Cl at 0 deg = 0.15 Cl at 9 deg = 1.2 AR =7

Q: Q2-B- Fill in the blank with the correct answer. 1. When the resultant of force system acting on a…

Q: 1. Derive the 3rd Order, non-linear, Blasius equation, as shown in class F"" + 1/2 FF" =0. Explain…

Q: Carbon dioxide gas initially at 500°F and a pressure of 75 psig flows at a velocity of 3000 ft/s.…

A: Given data: Temperature of Carbon Dioxide = T = 500°F = 533.15 K Pressure of carbon dioxide = P = 75…

Q: 2.2) A cylinder and piston assembly contain water at 105°C and 85% quality, with a volume of one…

A: Given that: T1 = 105 C, x = 85%, V1 = 1L V2 = 1.5 L D = diameter of the piston k = spring constant…

Q: The slider P can be moved inward by means of the string S, while the slotted arm rotates about point…

A: Roulette ball placed on a roulette wheel & a race car travelling on a circular path are examples…

Q: Q2: The lecturer Aous used to drive his car early inorder to arrive and teach his students some…

Q: Q4) Choose the true answer of the following questions : (1) The engine speed is measured…

Q: = Q2: A 1.78 L four-stroke petrol engine was tested at 2500 rpm. The developed brake powe 28 kW and…

A: Given Volume, V= 1.78 L = 0.00178 m3 Brake power, BP = 28 kW Speed, N = 2500 rpm…

Q: A steel plate L2 of 0.125in thick and 2in thick width is folded into a 60in circular arc • Calculate…

Q: Calculate the polar moment of inertia of the following cross section about origin: Y₁ 30 mm 4 (A)…

A: Parallel Axis Theorem:- Let xc and yc be the centroidal axis and x and y are the other axis parallel…

Q: Q2: A 1.78 L four-stroke petrol engine was tested at 2500 rpm. The developed brake power is 28 kW…

A: Given Volume, V= 1.78 L = 0.00178 m3 Brake power, BP = 28 kW Speed, N = 2500 rpm…

Q: The piston of the hydraulic cylinder gives pin A a constant velocity v = 3.9 ft/sec in the direction…

Q: The impulse and momentum principle is mostly useful for solving problems involving whatquantities?…

Q: 1- The use of lubricant in wire drawing die.

A: we have to discuss the use of lubricant in wire drawing

Q: Q2-A- Use the graphical method to find the magnitude and direction of the resultant of these forces.…

A: Given

Q: 3. Hot water flows inside a 2.5 cm inner diameter tube, the tube has a wall thickness of 0.8 mm…

A: Given: Inner radius = 2.5 cm Thickness = 0.8 mm And 3 thermal resistances Correct answer: A 9.94…

Q: 3. A pump discharges 126 liters per second of brine (sp.gr.1.20). The pump inlet, 304.8 mm diameter,…

A: Given: The volume flow rate of brine, Q = 126 liters/s = 0.126 m^3/s The specific gravity of brine,…

Q: (7) A rod of 0.12in diameter is coiled into a tension spring of 20 effective coils with a mean…

A: Disclaimer: “Since you have asked multiple questions, we will solve the first question for you. If…

Q: The rigid bars AB and CD shown in Fig. are supported by pins at A and C and the two rods. Determine…

Q: Q2: A two-stroke diesel engine was electrically motored (non-firing operation) when the meter…

A: Given Brake torque, T = 120 N.m Speed, N = 600 rpm Calorific value, CV = 40.3…

Q: Establish a formula for the frictional torque transmitted by a cone clutch

A: Concept: There are two theories to estimate the torque transmitted by the cone clutch: 1) Uniform…

Q: A 250 kg part falls from an airplane and hits the ground at 150km/h a) find the kinetic energy

A: Mass of part, m=250 kgSpeed of part, V=150 km/h

Q: 6.2) There is a regenerative cycle that uses steam as the working fluid. Steam leaves the boiler and…

A: Answer: The thermal efficiency of the cycle is 37.455%.

Q: 1) For vapour contained in an engine 2 cylinder:

A: we have to discuss about the vapor contained in the system

Q: QUESTION 2. A smooth rod with a length of 21 is bent as in Figure 2 and small oscillations are made…

Q: The slider P can be moved inward by means of the string S, while the slotted arm rotates about point…

Q: Can you imagine what is the 3D of this in autocad?

Q: METHODS AND MATERIALS TECHNICAL PAPER

Q: Q3/ A particle moving along a straight line is subjected to a deceleration a=(-V) m/s, where is V in…

Q: For a robust composite, the interfacial strength between the continuous and discos phase O a.…

A: Given Composite To find How interracial strength is importance

Q: 6.1) A boiler produces 25 kg/s of steam at 3 MPa and 600 °C, cools the condenser with seawater so…

Q: homogeneous 50-kg suspended by origi at the same level. Each light steel springs consists of 24…

A: Given Data The mass of the block is:m=50kg The number of turns of the steel spring is:n=24 turns…

Q: Q3) The following reading was taken from the performance test of single cylinder four-stroke engine…

A: Answer: (1) Indicated power: 30.68 kW (2) Brake power: 21.20575 kW (3) Mechanical efficiency: 69.12%…

Q: Q2 Replace the distributed loading with an equivalent resultant force, and specify its location on…

Q: Q1/ From Fig (1) Determine: the magnitude of F1 and its direction 0 If you know that the resultant…

Q: 1- The change of piezometric head per unit distance in a given direction is the ....... ***

A: we have to fill in the blanks

Q: Make a comparison between the bath and state functions in the following points: 1) relation to path.…

Q: A flat belt is required to transmit 35 kW from a pulley of 1.5 m effective diameter running at 300…

A: Given, Power being transmitted = P = 35 kW = 35000 W Diameter of pulley = d = 1.5 m Rotational speed…

Q: Q2: The lecturer Aous used to drive his car early inorder to arrive and teach his students some…

A: Distance = 160 km Velocity =75 miles per hour = 120.7 km per hour

Question

Out of 100% energy injected into steam boiler, how many percentage goes into flue gas waste?

a. 28%

b. 33%

c. 15%

d. 20%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Which device can be used to recover waste heat from flue gas? a. flue gas recoverer b. boiler saver c. energy saver d. feedwater economizer
Choose the correct answer and show COMPLETEsolution. (Diesel Cycle)
7. An engine is required to produce 4500 kg of dry steam per hour. The quality of steam in it is 90%. What must be the weight of the wet steam? A. 4778 kg/hr B. 5000 kg/hr C. 5258 kg/hr D. 6000 kg/hr
1- What is the pressure at the Economizer (in bar)? 2- What is the pressure at the Evaporator (in bar)? 3- How much heat received by the Economizer (kW)? 4- How much heat received by the Evaporator (kW)? 5- How much heat received by the Superheater (kW)? 6- How much heat received by the FWH (KW)?.. 7- How much heat received from the fuel burning (kW)? 8- How much heat rejected at the chimney (kW)?. T=35 C From the Pump m-1.3 kg/s + Cpw=4.2 kJ/kg.C ****************** T=150 C, To the Turbine Cp 1.008kJ/kg.K T=400C 44 T=212.2 X=0.0 X=0.85 Chimney Hoo bou to Economizer Evaporator Super Heater -Air, m-4 kg/s, T=20 C P=5 bar, X=0.8, m=0.3 kg/s from FWH X=1 1 Fuel, T-20 C, m=0.2 kg/s, C.V=33.5 MJ/kg Bumer
1. An air-source heat pump is a heat-pump system that uses air: a. as the system refrigerant. b. as the heat source when operating in the cooling mode. c. as the heat sink when operating in the heating mode. d. as the heat source when operating in the heating mode. 2. According to the Department of Energy, duct leakage can result in a energy loss? a. 10% b. 20% c. 30% d. 40% 3. As the outside ambient temperature drops, the efficiency of a heat-pump system operating in the mode will: a. heating, drop b. heating, rise c. cooling, rise d. Both a and c are correct.
Air leakage does not affect the boiler plant efficiency, us this statement true or false
Atmospheric air leaves an air conditioning coil saturated at 10 degree C. The air passesthrough a reheater, which raises the temperature sensibly to 22 degree C. Most nearly,what is the saturation percentage of the air leaving the reheater?A. 47% B. 61% C. 84% D. 100%
Multiple Choice. Choose the correct answer and show COMPLETEsolution. (Diesel cycle)
In a cooling tower the evaporation loss means O a. the water loss due to evaportion O b. the water loss in the from of droplets O c. the water loss due leakages O d. the total water loss due to blowdown. ge
compressors is not true? compression cycle. B. In a scroll compressor, vapor is compressed by a series of pistons that travel in a spiral pattern through a fixed scroll. C. Compressed vapor is discharged from the center bailod ai of the scroll. Combre oiaed D. All of the above.
2. A diesel engine was tested for a continuous 3 hours of operation. It consumed at total of 5 liters and developed a constant power of 7.5 kW. If the fuel contains 45.46 MJ/kg, what is the approximate thermal efficiency? a. 40% b. 35% c. 33% d. 25% e. none of the above
Please help me. (45 mins. left), I'll give a thumbs up) Given the ultimate/gravimetric analysis of coal as follows: C=81.95%, H2 = 4.63%, S=0.96%, N2=1.3%, O2=5.75%, Ash=6.09%, Moisture = 3.05% Using ash and moisture free analysis. Determine the; mass of the wet flue gas