For a hydraulic device, a piston has a cross-sectional area of 40 square centimeters moving an incompressible liquid with a force of 75 N. The other end of the hydraulic pipe is attached to a 2nd piston with a force of 150 N. Determine the cross-sectional area on the second piston? (Note: 1?2 = 10 000 ??2 = 104??2)

For a hydraulic device, a piston has a cross-sectional area of 40 square centimeters moving an incompressible liquid with a force of 75 N. The other end of the hydraulic pipe is attached to a 2nd piston with a force of 150 N. Determine the cross-sectional area on the second piston? (Note: 1?2 = 10 000 ??2 = 104??2)

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 89P: A container of water has a cross-sectional area of A=0.1m2 . A piston sits top of the water (see be...

See similar textbooks

Similar questions

A teenager is stealing gasoline from his father's car with a siphon with diameter of 12 mm. The heights in the figure are: z1 = 970 mm and z2 = 181 mm. Calculate the volumetric flow rate out of the tank. Round off the answer to two decimal digits in l/s, but enter your answer without the unit. Z₁ Answer: 22
A hydraulic lift has two pistons, large (d=300mm) and small (d=15mm). A force of 500 N is exerted on the small piston. What is the resulting force on the large piston, which is used to move the load? Enter the answer in KN without decimals. Answer:
A hydraulic press has one piston of diameter 6.3 cm and the other piston of diameter 17.7 cm. What force must be applied to the smaller piston to obtain a force of 1,506 N at the larger piston? Express your answer in N, to at least one digit after the decimal point. -X 191.5
The large cylinder of a homemade automobile hydraulic lift is 18 inches in diameter. The large cylinder is used to lift a 2400 lb auto: F1 = 2400 lb. The force applied to the small cylinder of the system is 600 lbs. What is the area of the larger cylinder in units of square feet? Use 3.14159 as the value of Pi. Round final answer to 3 decimal places. What is the diameter of the smaller cylinder in inches? a) = A1 _________________ft b) =d2 __________________ inch
The following figure shows the shape and dimensions of a small dam. Assuming the water level is at the top of the dam, find the total force on the face of the dam. NOTE: pg = 9800
Let's see how Pascal's law can be used to amplify a force. Suppose the hydraulic lift shown in (Figure 1) has a small cylindrical piston with radius 5.0 cm and a larger piston with radius 20 cm. The mass of a car placed on the larger piston's platform is 1000 kg. Engineers are designing a hydraulic lift that can be used to repair trucks with a mass of 6800 kg . What ratio of piston areas would you suggest for the design if the maximum available external force is to be 3000 N ?
What is the minimum area (in square meters) of the top surface an ice slab 0.369 m thick floating on fresh water that will hold up a 1220 kg automobile? Take the densities of ice and fresh water to be 917 kg/m and 998 kg/m°, respectively. Number i Units
The tank below holds a liquid with a density of 1,318 L =4.7 meters and 0 =47 degrees. The width of the wall (into the page) is 0.7 meters. What is the magnitude of the force on the right wall? Give your answer in kiloNewtons. 0 kg m³ L
Question: Where did you get the 13,885.33 tonnes? Please provide explanations and can you illustrate the problem? Problem: A ship arrives at the mouth of a river in water of density 1016 kg per cu. m with a freeboard of ‘S’ m. She then discharges 150 tonnes of cargo, and proceeds up river to a second port, consuming 14 tonnes of bunkers. When she arrives at the second port the freeboard is again ‘S’ m, the density of the water being 1004 kg per cu. m. Find the ship’s displacement on arrival at the second port. Thank you so much. I am having a hard time to understand it an illustration and detailed explanation will be very helpful. Thank you.
A cargo ship of mass 50000 metric tonnes is floating in the Great Lakes. The Great Lakes are fresh water, so we can assume a density of 1000kg/m³. What is the volume of water displaced by this cargo ship? m3 Submit Answer Tries 0/2 If the volume of the cargo ship is 1.43x105 m³, what percentage of the ship's volume is below water? %
an object has a total volume of 5 liters (which is 5000 cubic centimeters) and a mass of 4 kg. What is its density (g/cm 3power)? Will it sink or float in water?
A block of lead has dimensions of 4.50 cm by 5.20 cm by 6.00 cm. The block has a mass of 1.59 kg. From this information, calculate the density of lead in kg/m3.