Find the pressure at depth of 2.556 m from top of water. Take density of water as 1000 kg/m3
Q: List as many problems encountered with water-hardening steels as you can think of.
A: given; problem of water hardening steel?
Q: Which one of the following statements is true
A: Given data, 4 bar mechanism with all revolute pairs has link lengths, lf=20 mm lin=40mm lco=50mm…
Q: he bending moment Mis VY M
A: Given:Force acting on the section, F=25 kNDistance between the forces, x=3 m
Q: A pump supplies oil at 0.0002 m3/s to a 50 mm diameter double acting cylinder and a rod diameter is…
A:
Q: The velocity of a 1.2-kg particle is given by v = 1.5t³i+ (2.4 3t2)j + 5k, where v is in meters per…
A:
Q: Q1: Determine the resultant of the force system in next fig. Then locate this resultant with respect…
A:
Q: дл др Os ӘТ S Cp
A: Write the expression at constant enthalpy. dh=Tds+vdP0=Tds+vdP∂s∂ph=-vT
Q: The value of stress amplitude (in MPa) i
A: Given, Minimum stress,σmin=200 MPaMaximum stress,σmax=400 MPaFind the value of stress amplitude ?
Q: A particle moving in the x-y plane has a position vector given by r = t²i+t³j, where r is in meters…
A:
Q: If the outside barometric pressure reading shows 0.285235 ft Hg. What is the airplane’s vertical…
A: Given:Barometric pressure reading outside the airplane's, h=0.285235 ft HgFind: The airplane's…
Q: 3. The brakes of a car are applied, causing it to slow down at a rate of 10 ft/s2. Knowing that the…
A: Given: displacement s= 300 ft deceleration a = -10 ft/s2 To find: (a) initial velocity u = ? (b)…
Q: 1. A uniform bar of length L, cross-sectional area A, and mass density p is suspended vertically…
A: Given data: A vertically suspended bar have following properties: ◆ The length of the bar = L ◆ The…
Q: a: Sketch within a cubic unit cell the following crystallographic directions: [121]. (2011. [213].…
A:
Q: 3/114 The 4-kg ball and the attached light rod rotate in the vertical plane about the fixed axis at…
A:
Q: When sharpening layout tools and other tools, what is the most important consideration?
A: Given Tools To find Important consideration The tool is a sharpening process refining 2…
Q: The quadratic prism OABCKLMN. if a=24 m, b=7m, and c=10 m. The prism has width h=14 m. The forces F1…
A: We can answer up to 3 sub-parts so we will answer first 3 for you. Please resubmit the question by…
Q: b) The shaft shown in figure 6 supports the three pulley loads. The shaft is made of steel and has a…
A:
Q: For laminar forced convection over a flat plate, if the free stream velocity increases by a factor…
A:
Q: A machine component is undergoing a torque load. The part is made up of a 1 m long composite bar. It…
A: GIVEN DATA- Rod and Tube combination shaft given Subjected to Torque We have to find Angle of twist…
Q: barlupar Importance tance the eirele in Machine Design! Step by step Proper explamation needed here
A: The circle is most important geometric element for machine design. It is used for stunning designs…
Q: A cylindrical boiler with an inside diameter of 2.5 m and a wall thickness of 40 mm is made of a…
A: GIVEN DATA- Pressure P=1.5MPa Internal Dia d=2.5m = 2.5*1000=2500mm Thickness t=40mm Yield stress…
Q: 2/21 During an 8-second interval the velocity of a particle moving in a straight line varies with…
A: Given data: from the given graph, ◆ At t = 0 sec, vmin = v0 = 4 m/s ◆ At t = 8 sec, vmax = 12 m/s ◆…
Q: The small object is placed on the inner surface of the conical dish at the radius shown. If the…
A: r = radius of the disk = 0.2 m μs = coefficient of static friction between the object and the…
Q: Sketch the distribution of the shear stress due to torsion in a circular shaft. (simple sketch of…
A: Given : shear stress due to torsion in a circular shaft varies with shaft radius To find : Sketch…
Q: The best approximation for a,
A: Given data, Flywheel having mass=m Rim of radius=RConcentric disk like feature of radius=R/2Flywheel…
Q: Q2: Determine the resultant of the force system in next fig. Then locate it with respect to poin…
A: Given
Q: Determine the (magnitude of ) moment of the
A:
Q: Below is a polymer curve of mechanical PVC (a) true stress (MPa) 180 160 140 120 100 80 60 40 20 0.2…
A: The given question is related to material science.
Q: ntroduced in a room at such a rate that the air is changed every 2 minutes. The room is 46ft by 38ft…
A: Given Data as per questionDimension of room Room, =46 ft×38 ft×10 ftAir is changed in room every 2…
Q: Suppose a penstock delivers water through an elevation change of 32 m and produce total output…
A: data given in question: electric power or shaft power= 5.45kW total efficiency ηo=69% ηo =shaft…
Q: Given: Two (2) identical pumps series in connection Suction Pressure = 3.2 Bars Discharge Pressure =…
A:
Q: In a rolling operation using rolls of diameter 500 mm if a 25 mm thick plate cannot be reduced to…
A: Given:Diameter of rolls. D=500 mminitial thickness of plate, h1=25 mmfinal thickness of plate,…
Q: The COP of the cycle is
A: Given. T1=100C h=402 kJ/kgT2=500Ch=432 kJ/kgDetermine the COP of the cycle ?
Q: *1-4. Determine the resultant internal loadings in the beam at cross sections through points D and…
A:
Q: Ex. No. 3: Determine the values of the shear stress owing to bending at point A, B3, and C in the…
A:
Q: The object in the diagram below is called a Warren truss. (Figure 1) For the system of parallel…
A: Given data: F1=420 NF2=876 NF3=1542 N Need to determine the equivalent resultant force of the system…
Q: the maximum torque (in N.m) that can be
A: Given data, A disc with a single friction surface has co-efficient of friction,μ= 0.3Max.…
Q: m.i Water at m = 0.02 kg/s and T = 20°C enters an annular region formed by an inner tube of diameter…
A: Given data: m=0.02 kg/s˙Di=25 mmTm,i=20°CDo=100 mmTs,i=100°CTm,o=75°C Need to determine the length…
Q: kindly discuss the impact of a scale on a ship model and give one example of a predominant force…
A: We will discuss the impact of a scale on a ship model and give one example of a predominant…
Q: When sharpening layout tools and other tools, what is the most important consideration?
A: During the sharpening layout tools or other tools, there are few terms which are most important…
Q: b) Discuss the modal analysis method.(short Answer) c) What is meant by sweeping matrix? d)…
A:
Q: ve- 37 For the instant represented the particle P has a ve locity v = 6 m/s in the direction shown…
A: Write the given data. v=6 m/sax=15 m/s2aθ=-15 m/s2
Q: A gear train is made up of five spur gears as shown in the figure. Gear 2 is driver and gear 6 is…
A: Given data: ◆ The gear train consists of total five gears: Gear 2 ---> Driver member Gear 6…
Q: 3. Explain the concept and the relationship between state of stress at a point and transformation of…
A:
Q: Example 14.2 A cold fluid is heated from 40°C to 120°C by condensing steam at 180°C. Calculate the…
A:
Q: Thistic ticerkep a door mn To keep a door closed, a wooden stick is wedged between the floor and the…
A:
Q: Calculate the modulus of rigidity (shear modulus) of an epoxy resin if the modulus of elasticity…
A: Given:Young's modulus, E=3.5 GPaPoisson's ratio, μ=μ0.35
Q: The X coordinate of the centroid of a right- angled triangle of base b and height h is
A: Given data : Base of right angled triangle=b Height of right angled triangle=h Required : X…
Q: A force P is inclined at 60° to the horizontal. If the horizontal component of force is 50 N find…
A:
Q: Intstruction: Solve for the reactions of the following bean.
A:
Step by step
Solved in 2 steps with 2 images
- One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.Determine the volume of the concrete arch dam.Find the pressure at depth of 2.556 m from top of water. Take density of water as 1000 kg/m3
- 3_Calculate the volume if it is v1=1.5 L, P1= 100 Кра, р2- 50 kpa.2. The tank shown contains alcohol (SG=D0.78) and covered by a circular plug 1.2 m in diameter. Calculate the hydrostatic force F Am acting on the plug and its center of pressure. 8m 1.2 m 3. The gate as shown is 3 m normal to the page. It keeps the two liquids from mixing with each onough clocuro botween the oil andFind the vlaue of height of diffrence of the liquid in the manometer if the manometer pressure is 100kPa. use the density of Hg from standard book at normal condition.
- Find the vlaue of Pressure if the manometer reads 0.01 mm. use the density of Hg from standard book at normal condition.3- Find the total pressure and position of center of pressure FREE WATER SURFACE on a triangular plate of base 2 m and height 3 m which is 60 2.5 immersed in water in such a way that the plane of the plate h* -2 m makes an angle of 60 with the free surface of the water. 3 m YP The base of the plate is parallel to water surface and at a depth of 2.5 m from water surface.A simple manometer (U tube) containing mersury is connected to a pipe in which an oil sp.gr. 0.8 is flowing . The pressure in the pipe is vacuum. The other end of the manometer is open to atmosphere. Find the vacuum, pressure in the pipe, if the difference of mercury level in the two limbs is 20 cm and the height of oil in the left limb from the center of the pipe is 15 cm below. a.-64.74 b.-278.6 c.-120.58 d.-25.11