Figure Q3 shows the water, which is drawn into the pump, such that the pressure at the inlet A is 40 kPa and the pressure at B is 120 kPa. If the discharge at B is 0.15 m³ /s, calculate the power output of the pump. Neglect friction losses. The pipe has a constant diameter of 100 mm. take h = 1.5 m. B

Figure Q3 shows the water, which is drawn into the pump, such that the pressure at the inlet A is 40 kPa and the pressure at B is 120 kPa. If the discharge at B is 0.15 m³ /s, calculate the power output of the pump. Neglect friction losses. The pipe has a constant diameter of 100 mm. take h = 1.5 m. B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The diameter of the pipe at the larger end is 0.50 cm and at the smaller end is 0.20 cm, the larger and smaller ends located 7 meters and 3 meters respectively, from the datum line. If the larger end, the velocity is 1.2 m/s and the pressure is 5200 kN/m2 , compute the velocity at the smaller end.
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pump
Reservoir B 3. A pump draws water at 300 liters per second from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1 is 20 times the velocity head in the 200 mm diameter and the head loss from 2 to B is 20 times the velocity head in the 150-mm diameter pipe. Assume your own reservoir B elevation then compute for the energy that must be supplied to the pump in kW if said appurtenance has an efficiency of 80%. Compute also the pressure at points 1 and 2. Z 150 mm Reservoir A 200 mm pipe Pump 4. The same venturi meter described in number 2 is used to measure the discharge for a length of pipeline that was suspected to have had water stolen through an illegal connection. Before said suspected illegal connection, a mercury difference of 350 mm was observed while a mercury difference of 200 mm was observed afterwards. Estimate the stolen volume of water per day. Elevation=-20 m Point 1 Point 2
Question 2: A Pelton wheel turbine is used in a hydroelectric plant to generate electric power. In this turbine, a high-speed jet with a velocity of V, impinges on buckets at a radial position of r, forcing the wheel to rotate. The Buckets reverse the direction of the jet, and the jet leaves the bucket making an angle B with the direction of the jet, as shown in the figure. Vi Shaft Vi Nozzle Vix y If the wheel has a counterclockwise angular speed of w, what would be a) the magnitude of fluid stream velocity leaving the bucket, V. What would be the velocity component in the horizontal direction, V? b) Assume the volumetric flow of water is Q and its density is p. Derive a formula for the torque applied on the wheel, T, from water. Derive a formula for power, W, that this wheel can deliver as a function c) of V,. B, w, r, and p. d) Wmax? At what angular speed, w, does the wheel delivers its maximum power,
A liquid (SG = 0.562) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -9 psi and 41 psi, respectively. The rate of flow in the pipe is 0.898 ft3/s. What will be the rating of the pump (in horsepower) if its efficiency is 90%? Neglect energy (friction) losses in the system. Use x = 5 ft., y = 9 ft. Use 1 hp = 550 lb-ft/s. Round off to two decimal places.
Find the force required to hold the blade in position, if the jet weight (100kg) and discharge (400l/sec).
The reservoir tank shown contains fresh water air pressurized to 200 kPa. There is a loss of 3.3 N*m/N due to friction in the pipes. Point 1 is located at the surface of the water and point 2 is in the free stream of the exit spray. The Distance from the water surface to the free stream is 3 meters. The flowrate for the system is .05 m^3/s (Work on paper required) 1. How much energy is provided to the motor by the flowing water? 2. Assuming the motor has an efficiency rating of 83%, how much power is output? Ar Pressure o water DN 50sch 40 motor r coo ON 80 sch 40
As part of a processing of biofuels, water is pumped into a circular tank with a diameter Dt, as shown in Figure Q3. The flowrate into the tank is Q1 and the flowrate out is Q2. When the vessel is heated, water evaporates. The average velocity at which the vapour rises across the entire tank is vevap. You may assume that water has a density of pw, and vapour has a density of pu. Acceleration due to gravity is g. a) Find an expression for the rate of change of the mass of water in the tank. b) At time t = 0, the height of water in the tank is 10. Find an expression for the height as a function of time, h(t). c) An alarm is triggered when the pressure at the bottom of the tank exceeds palarm. Find an expression for the time at which the alarm goes off. Q₁ Vevap 2₂ D₁ Figure Q3: Water being pumped through a heated evaporation tank.
A high-pressure washing system's pump supplies 1 gallon of water persecond at 100 psi pressure. The nozzle should be designed so that the static pressureof the water as it exits the nozzle is the same as the atmospheric pressure. If theinside diameter of the hose leading from the pump to the nozzle is 2 in., whatshould the diameter of the nozzle exit be? What will be the velocity of the waterat the exit of the nozzle?
As part of a processing of biofuels, water is pumped into a circular tank with a diameter Dt, as shown in Figure Q3. The flowrate into the tank is Q₁ and the flowrate out is Q2. When the vessel is heated, water evaporates. The average velocity at which the vapour rises across the entire tank is vevap. You may assume that water has a density of Pw, and vapour has a density of pv. Acceleration due to gravity is g. a) Find an expression for the rate of change of the mass of water in the tank. b) At time t = 0, the height of water in the tank is ho. Find an expression for the height as a function of time, h(t). c) An alarm is triggered when the pressure at the bottom of the tank exceeds Palarm. Find an expression for the time at which the alarm goes off. Q₁ } } Vevap D₁ Figure Q3: Water being pumped through a heated evaporation tank.
If the velocity of water is 8m/s and the pressure is 140 kPa on the discharge side of a pump, What will be the head of the pump if the velocity is 4 m/s and the pressure is 90 kPa on the suction side of the pump? How much power is required to drive it if the diameter of suction side is 600 mm? If the pump is rated at 120 hp, what is the efficiency of the pump neglecting energy losses in the system?
A pump draws water from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe and the head loss from 2 to B is twenty-five times the velocity head in the 100-mm diameter pipe. The discharge in the pipe is 20 liters/second. Find the power delivered by the pump in kW. Calculate the pressure head at point 1 in meters. Solve the pressure head at point 2 in meters.