Determine the magnitude and direction of the anchoring force needed to hold the horizontal elbow and nozzle combination show in place. At section (2), water discharges into the atmospheric at 100 kPa and the pressure at location (1) is 100 kPa gauge. 160 mm V₂

Determine the magnitude and direction of the anchoring force needed to hold the horizontal elbow and nozzle combination show in place. At section (2), water discharges into the atmospheric at 100 kPa and the pressure at location (1) is 100 kPa gauge. 160 mm V₂

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Oil at 38 deg. Celsius is being drawn from a closed tank having a pressure of 70 kPa gage. The level of oil in the tank is 2.5m above the pump centerline. The suction line friction loss is 0.6m. The vapor pressure of the gasoline is 48 kPa absolute and its specific gravity is 0.82 Determine the NPSH in meters available.
Determine the available suction head of a pump that is taking gasoline at 204 deg. C, from a closed tank with a pressure of 585 Kpa gage. The specific gravity of gasoline is 0.78 and its vapor pressure is 620 kpa absolute. The loss in the suction pipe is 0.5m and the pump centerline is located 3.60 meters above the gasoline level. answer is 4.47 how
Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as shown in the figure below.. Note that p°- 1.013*105 Pa Calculate the absolute pressure (Pa). Density: Pwater = 1000 kg/m Pail = 800 kg/m Pand = 200 kg/m P. h3=12 cm hg al2cm oIL Pa h25 cm ng = 6 cm %3D Sand water
Problem 3. Outcome 5. Please show all work. Air at standard pressure but with T= 50°C flows through the ducting system shown in the figure. The gauge measures the pressure difference between the downstream and upstream points. All duct sections have circular cross section. Use the following geometry: D₁ = 60 mm, D, = 200 mm, L= 2 m. At this temperature, ai = 1.95 x 10-5 kg/m-s. Also recall that Rai = 287 J/kg-K. The center pipe is smooth with e0. Ap Voo D2 L D₁ Dz Figure for problem 3. The velocity entering the system, Voo; is measured to be 20 m/s. Estimate the Ap = Pdownstream Pupstream measured by the pressure gauge.
Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as shown in the figure below... Note that p° = 1.013*10$ Pa Calculate the absolute pressure (Pa). Density: Pwater = 1000 kg/m³ Poil = 800 kg/m' Psand = 200 kg/m' %3D h3=12 cm oiL Pa hi=5 cm h2=6 cm !3! →Sand water
what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=6.1, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle. 70 cm mis 2ns 60 cm Liquid
The pressure reading coming out of a pump is 150 lb. Every 50 ft section reduces the pressure by about 4%. What will the nozzle pressure be at the end of six 50 ft sections? (Hint: One reduction of 24% is not equivalent to six reductions of 4% each. You must do this the long way.)
A certain turbine has a capacity of 45 ft³/s. 3ft³/s is lost during the flow. The tailwater is 14 7 ft from the center of the turbine. The intake measures 35 in and the pressure is measured by mercury u-tube manometer which measures 15.566 ft in the intake and 3.00 ft in the discharge side. The datum of the scale is at 5.62 ft below that of the center of the turbine. The brake power output was 767.8 kw. Losses is measured to be 20.2 KW. Calculate the efficiency of the turbine
*83. Go Two hoses are connected to the same outlet using a Y-connector, as the drawing shows. The hoses A and B have the same length, but hose B has the larger radius. Each is open to the atmosphere at the end where the water exits. Water flows through both hoses as a viscous fluid, and Poiseuille's law [Q = ™R°(P2 – P)/(8nL)] applies to each. In this law, , P, is the pressure upstream, P, is the pressure downstream, and Q is the volume flow rate. The ratio of the radius of hose B to the radius of hose A is Rg/RA = 1.50. Find the ratio of the speed of the water in hose B to the speed in hose A. Water from outlet Hose A Hose B Problem 83
A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from (1 to 2) was (100m) Determine the length of pipe from (2 to 3), and the pressure at point (2). (e-0.026mm, v1.13" 10 m?/sec). Fig(1) 6m 23m Fig.(1) Nozzle
A small, high pressure water jet can be used for cutting various materials. A jet with a speed of 700 m/s and a diameter of 0.10 mm is required for precision cutting. Determine (a) the pressure within the nozzle (KPa gauge) and (b) the force (N) needed to hold the nozzle to the pipe for the nozzle shown below. L = 4.54 mm d = 1.50 mm L = 1.57 mm d = 0.10 mm
A pump test for air flow is set up as shown below in which the pump draws air from the atmosphere into the 1-ft diameter pipe. The liquid in the differential manometer is water (? = 62.4 ?b/??^3) and the density of air is 0.00238 ?lug/??^3. Assume that the air flow is incompressible and frictionless. (a) Using the piezometer tube, compute the pressure in the pipe. (b) Using the Pitot tube and an energy equation, compute the velocity in the pipe. (c) Assuming that the air far away from the entrance to the pump is at rest (zero velocity), calculate the power delivered by the pump.