Design an Excess-5-to-BCD code converter. Using K-map, determine the Boolean expression of the required output signals in POS Only the required output signals should be shown on your answer sheets. Encircle/bpx your final answer. (a) The output signal K (b) The output signal L (c) The output signal for J (d) The output signal for M NOTE: Support your answer by showing the truth table of the circuit and maps with appropriate group labels. Your answer should conform to the correct entries in your truth table.

Design an Excess-5-to-BCD code converter. Using K-map, determine the Boolean expression of the required output signals in POS Only the required output signals should be shown on your answer sheets. Encircle/bpx your final answer. (a) The output signal K (b) The output signal L (c) The output signal for J (d) The output signal for M NOTE: Support your answer by showing the truth table of the circuit and maps with appropriate group labels. Your answer should conform to the correct entries in your truth table.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

The following waveforms are the input to the shift register you constructed in question #5. Based onthe waveforms for the CLK (clock) and D0 input (input on the leftmost Flipflop), generate thewaveforms for Q0, Q1, Q2, Q3, Q4. (Question #5 is "Using JK-Flipflops and Digital Logic Gates, build a 5-stage Shift Register")
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
1. Gray code to Binary converter: Gray code is one of the codes used in digital systems. It has the advantage over binary numbers that only one bit in the code word changes when going from one number to the next. (See Table 1). Design a combinational circuit with 4 inputs and 4 outputs that converts a four- bit gray code number into an equivalent four-bit Binary number. Use Karnaugh map technique for simplification. Use LogicWorks for pre-lab demonstrations. Select the library "7400dev.clf* in the Parts Palette and then select the XOR chip 74-86. This would give you a set of 4 XOR's as shown in Fig. 1, just like the hardware chip 74-86. You could use as many as needed from these XOR gates in your design. Get back to ALL LIBRARIES and select switches for the inputs and Binary Probes as indicators of the outputs. Verify your design in the pre-Lab. During the Lab construct the circuit and verify its operations.
Design a combinational circuit with the four inputs A,B.C, and D, and three outputs X, Y, and Z. When the binary input is odd number, the binary output is one lesser than the input. When the binary input is even number the binary output is one greate than the input. Implement the function using multiplexers with minimal input and select line.
Design a code converter that converts a decimal digit from BCD to excess-3 code, the input variables are organized as (A BC D) respectively with A is the MSB, the output variables are organized as (W X Y Z) respectively with W is the MSB, put the invalid decimal numbers as don't care. X= BCD'+B'D+B'C X= BC'D'+B'D+BC X= BC'D'+B'D+B'C X= BC'D'+BD+B'C
Excess-3 code is significant for arithmetic operations as it overcomes shortcoming encountered while using 8421 BCD code to add two decimal digits whose sum exceeds 9. Excess-3 arithmetic uses different algorithm than normal non-biased BCD or binary positional number system. An electronics company has hired your services to design a code converter that converts Binary Coded Decimal (BCD) code for it. Design the converter.
Simplify by using Boolean algebra (show all the steps)
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following indicator figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, The logic "0" will be applied to the burned parts. Draw this circuit.
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following indicator figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, Logic "0" will be applied to the burned parts. The accuracy of the logic circuit you will design Create the table and find the output expressions by shrinking the table with the Karnaugh diagram method.
Construct a circuit diagram consisting of a 7-segment display output when the BCD code input is set to be 1001. Your answer MUST include a diagram and the list of segments of the 7-segment display that will light on when 1001 BCD input is applied.
USE DIGITAL LOGIC AND DESIGN Part 1: In Figure_4; we have 4-bit Comparator using 2-bit Comparators block. You have to satisfy given condition by applying all data on figure 4. At the end, given condition should produce HIGH output and other two should be LOW. A3 A2 A1 A0 = 1101 and B3 B2 B1 B0 = 1110 Figure_4 Part 2: The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure_5. Determine the data-output waveforms from D0 through D3. Figure_5 Part 3: Decoder can be useful when we have to decode some specific numbers from their equivalent code. Figure 6 has a concept of 3 to 8 line decoder from which you have to generate output waveform from D0 to D7 with proper relationship to input. Figure_6 Part 4: The data-input and…