4.11 Electrical Apparatus 4.11 A 16/ KVA, 13200: 240 volt s ingle phasetrans former hasThe power input atR.eIoad0.01035 ohm and X" = 0.0131 ohm.with 13,200 volts impressed on the primary is 2000 watts.termine: (a) %R and %X; (b) copper loss at full load; (c) effi-ciency at full load and 80% lagg ing power factor.noDe-

In this question, We need to determine the ZR and Zx , copper losses, and efficiency at the 80%…

4, 11 A 16/ KVA, 13200:240 volt single phase R. foad trans former has 0.01035 ohm and X" with 13,200 volts impressed on the primary is 2000 watts. termine: (a) %R and %X; (b) copper loss at full load; (c) effi- ciency at full load and 80% lagging power factor. = 0.0131 ohm. The power input at no De-

4, 11 A 16/ KVA, 13200:240 volt single phase R. foad trans former has 0.01035 ohm and X" with 13,200 volts impressed on the primary is 2000 watts. termine: (a) %R and %X; (b) copper loss at full load; (c) effi- ciency at full load and 80% lagging power factor. = 0.0131 ohm. The power input at no De-

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

If we increase the load than core loss and copper loss will... Decrease Increase Remain same
In small transformers, the total copper loss may vary from the rated output. % of O 0.2 to 0.6 O 0.5 to 1 O 0.8 to 1.5 O 0.4 to 1
3. What are the classifications of Core Loss and Copper Loss?
An RLC series circuit connected to a 110 – volt and 50 – cycle AC source, contains the following series resistances and reactances: R1 = 10 ohm, R2 = 15, R3 = 5 ohms, XL1 = 20 ohms, XL2 = 25 ohms, XC = 40 ohms. Find the following: a.) EQUIVALENT REACTANCE b.) TOTAL IMPEDANCE c.) VOLTAGE DROP ACROSS THE CAPACITOR d.) TOTAL INDUCTANCE IN MILLIHENRY e.) TOTAL CURRENT f.) REACTIVE POWER g.) REAL POWER DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES
(5) Primary AC Source Transformer Secondary AC/DC Full-wave Rectifier Capaictor in Non- linear Load Figure 6 Analyse different methods of harmonics mitigation to eliminate the harmonic, which you have identify in above power system circuit. You can use harmonic filters, K or equivalent transformers or oversized neutral method depending upon the harmonic sources.
If the core of LVDT is at the middle, then the output voltage will be a. maximum b. minimum c. Output voltage is no relation with core position d. 0
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
The maximum flux density in the core of a 250/3000V, 50Hz single phasetransformer is 1.2 Wb/m2. If the emf per turn is 8 volt, determinea) Area of the core
2. Why the core losses varying with the load?
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit.
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
Transformers.