QUESTION NO: 2Design a memory system for the 8088 Microprocessor such that it can select twoEPROMS (128K x 8) using 2 to 4 line decoder with starting address A0000H.How many address pins of 128Kx8 memory are required to connect it with amicroprocessor?Find the starting and ending address of each EPROM device.Draw the complete interface diagram.i)ii)ii)

Answered: Image /qna-images/answer/34466a02-ed5f-412e-87a4-04df4f771f4d.jpg

Design a memory system for the 8088 Microprocessor such that it can select two EPROMS (128K x 8) using 2 to 4 line decoder with starting address A0000H. i) How many address pins of 128KX8 memory are required to connect it with a microprocessor? Find the starting and ending address of each EPROM device. Draw the complete interface diagram. ii) iii)

Design a memory system for the 8088 Microprocessor such that it can select two EPROMS (128K x 8) using 2 to 4 line decoder with starting address A0000H. i) How many address pins of 128KX8 memory are required to connect it with a microprocessor? Find the starting and ending address of each EPROM device. Draw the complete interface diagram. ii) iii)

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 2PE: If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the...

See similar textbooks

Similar questions

If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the fetch cycle is 40% of the processor cycle time, what memory access speed is required to implement load operations with zero wait states and load operations with two wait states?
Draw pinouts of 8088 or 8086 microprocessor (µp). Also draw schematics of 8088/8086 µp buses with Latch(s) [IC: 74LS373] and Buffer(s) [IC: 74LS245]. Write purpose of using latch and buffer ICs with µp buses.
Consider a simple read-only memory (ROM) unit with 2-bit addressand 2-bit data buses.Draw the internal architecture of such a ROM unit includingtransistors, address and data signals, and the row decoder.? I have attached the answer to the question, but I am confused by it, if you could explain every step including how many transistors to use, where to place them and the basic procedure which could be used with other similar questions that would be helpful
in 80886 microprocessor Suppose that. DS = 0200H, BX = 0300H, and DI-400H Determine the memory address accessed by each of the following instructions, assuming real mode operation: (1) MOV AL,[1234H] (2) MOV AX,[BX] (3) MOV [DI]AL
Consider a simple read-only memory (ROM) unit with 2-bit addressand 2-bit data buses.Draw the internal architecture of such a ROM unit includingtransistors, address and data signals, and the row decoder.? I have attached the answer to the question, but I am confused by it, if you could explain every step including how many transistors to use, where to place them and the basic procedure which could be used with other similar questions that would be helpful, do not copy and paste off chatgpt
Design the hardware required to interface 64KB of SRAM to the demultiplexed address and data bus of the 8086 Microprocessor connected in minimum mode using 32Kx8 memory chips. Decode the memory with simple NAND gate decoder so that it starts from physical address 00000h also for each memory chip used in your Design determines the physical address.
The Kiwi™ memory architecture design team has a dilemma. The team is considering several different memory configuration variations for an upcoming machine design. Consider the following designs (All memory accesses are in terms of bytes, and all are using paging techniques): Characteristic Design 1 Design 2 Design 3 Physical Memory Address Width 8 bit 16 bit 32 bit Logical Address Width 12 bit 20 bit 24 bit Page/Frame size in bytes 16 bytes 32 bytes 64 bytes Page Table Type Single Single Double a) For each design, list the maximum number of pages each process can access in logical address space. b) For each design, list the maximum number of frames in physical memory.
3. If we have an 8 bit microcontroller that has 4kB of instruction memory starting at address 0x0000, and 2kB of data memory immediately above that, what is the next available byte in our address map?
4. FIGURE 1 shows how a 3 to 8 line decoder (TTL 74138) can be used in conjunction with NAND gate (TTL 74133) to connect a set of switches to the data bus of a microprocessor system via buffers (TTL 74367). Answer the following questions relating to the diagram: a) What address, in HEX, is required on the address bus in order toread the switches? b) RD and MEMRQare control lines from the CPU. What must their logic state be in order to read the switches? Data bus 74 367 74 133 74 138 A15 D7 DO EN EN Address bus MEMRQ A4 A1 A0 EN TRUTH TABLE CBA|O 12 3 4 5 0 0 00 111 1 1 11 0 0 6 110 1 1 1 1 1 1 0 1 01 10 1 1 1 1 1 0 1 11 1 10 1 1 1 1 1 0 01 1 1101 1 1 10 11 1 1 1 101 1 1 101 1 1 1 1 1 0 1 1 1 11 1 1 1 1 1 1 0 74 367 (part of) FIGURE 1 Data enable Data outputs Input switches
Q1-Design the hardware required to interface 32KB of SRAM to the demultiplexed address and data bus of the 8086 Microprocessor connected in minimum mode using 16Kx8 memory chips. Decode the memory using two method the first one is with simple NAND gate decoder the second method is Decode the memory with 3-to-8-line decoder (74138). so that it starts from physical address 00000h also for each memory chip used in your Design determines the range of physical address which can handle. 9255 hin with 9096 microprocessors to work on on YO
interface four chips of 128k×8 SRAM to 8086 microprocessor using separate bank write strobes such that the upper and the lower banks each contains two chips. Identify the address range of the memory
A certain computer has a memory of 1M words, and each word is 32 bits long. Each instruction is 32 bits long and is consisted of an opcode field, a register address field to specify one of 32 registers, and a memory address field. How large must the register field be? How large must the address field be? How many different opcodes can be supported by this format? Show your reasoning