Consider the beam and loading shown. The allowable normal stress for the steel used is 152 MPa.NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.90 kNAB90 KNC0.6 m 0.6 m0.6 m90 KND-1.8 m-Determine the maximum value of the principal stress omax at the junction of a flange and the web.The maximum value of the principal stress omax isMPa. Determine the section modulus and select the most economical wide-flange shape that should be used to support the loading shownusing the table given.ShapeW460 x 74W410 x 60W360 x 64W310 x 74S (103 mm³)1460106010301050The section modulus is 1065 x 103 mm³.The most economical metric wide-flange shape is W410 × 60

Given Data The allowable normal stress acting on the steel is: σ=152 MPa The load acting on the…

Consider the beam and loading shown. The allowable normal stress for the steel used is 152 MPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 90 KN B 90 KN C 0.6 m 0.6 m 0.6 m 90 KN D 1.8 m- E

Consider the beam and loading shown. The allowable normal stress for the steel used is 152 MPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 90 KN B 90 KN C 0.6 m 0.6 m 0.6 m 90 KN D 1.8 m- E

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

BADLY NEEDED ANSWER ASAP Determine the shear stress (in Mpa) in the 20.75-mm-diameter pin at A that support the beam if P = 28.96 kN, a = 2.12 m, and b = 5.72 m. Round off the final answer to three decimal places.
The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form shown. The line of thrust of the drill passes through P. Find the greatest value the thrust may have without the tensile stress exceeding 15 MN/m2. What will be the stress along the face AB? (Cambridge) 12.4 19.0cm A 36 cm 1.60 cm 1.90 cm 1.60 cmT B. +17.5cm
Q-1 ) A thin cylinder of inner radius 150 mm and thickness 9 mm is subjected to an internal pressure of 9 MPa. The average circumferential (hoop) stress in MPa is equal to ?
Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft
A column is fabricated by adhesively bonding two aluminum faceplates to a foam plastic core as shown below. Note that there are only left and right aluminum plates (with no front and back plates). The foam plastic core has a square cross-section with elastic modulus Ef 1110 MPa. Determine the stress in the aluminum plates, the stress in the foam core, and the displacement of the column under the action of the applied force. = Note: Express tensile stresses as positive (+) and compressive stresses as negative (-). Given: • L1 L2 = = 100 mm = 1.7 m • . L3 = = 1.4 mm RIGID PLATE ALUMINUM FACE PLATE F FOAM L2 |← 41 +| |—–—– 63 L1 L3 F = 37 kN σα = σ f = |ɗ| = = number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) MPa ? MPa mm ?
A steel bar has a uniform cross sectional area of 300mm?. Calculate the stress at member AB. 1.6m 1.2m 1.8m 25KN SKN 1OKN
Find the maximum normal stress carried in the part shown. 0-Sin 0.5in 3in S000 1b lin 2in S000 1b 4in 2in
The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 19616 lb is applied at A? The d = 0.65-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
Required information Link AB, of width b = 2 in. and thickness t= in., is used to support the end of a horizontal beam. The average normal stress in the link is -21 ksi and the average shearing stress in each of the two pins is 12 ksi. 4 NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the diameter d of the pins. The diameter d of the pins is in.
Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each section is 0.50 inches. Give the answer in lb/in?. Assume Point A is a fixed support and the block at A is rigid. Indicate if it is in tension or compression. 3.50 kip 1.75 kip 5.00 kip B 3.50 kip A 1.75 kip 18 in: 12 in. 16 in: CAR= units II II
A cantilever beam, 80 mm wide by 230 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1200 N/m at the wall. Determine the magnitude of the stress in a fiber 60 mm from the top of the beam at a section 4 m from the free end. Answer must be in MPa.
Required information Consider the loading shown. The allowable normal stress for the steel used is 25.2 ksi. 48 kips 48 kips B 2 ft2ft C ·6 ft· 48 kips 2 ft For the selected design, determine the actual value of om in the beam. (Round the final answer to two decimal places. You must provide an answer before moving to the next part.) The actual value of Om in the beam is ksi.