Complete calculation for floating fastener application Complete the needed calculations and enter the needed values in the given table. All problems are for afloating fastener application.A.B.C.Hole dia at Fastener dia Allowable position toleranceat MMCMMCat MMC.189279.164190.031.029

Answered: Image /qna-images/answer/867f496d-b338-4814-9535-f6b79ea02031.jpg

Answered: Complete the needed calculations and…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The toleranced diameter of a hole is given as 0.990"/1.010" and the size of the mating pin is given as 0.985"/0.980 37. What is the maximum clearance for this fit? 0.030" 0.020" 0.025" c) 0.010" (P 38. What type of fit is this? transition b. clearance interference d. none of the above 39. A fit can be determined by specifying: upper limit b. allowance max. clearance b& c all the above TE d. 40. A fit is specified as 60H1109 in Metric unit. What is the tolerance grade for the shaft? 60 a. b. 9 11 d. none above
Complete an interpretation drawing that shows the required datum and the perpendicularity tolerance zone
I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following:What is the Bolt size (don't worry about the tolerances)?Dim's C=.75, B=2.50, apply a +/-.01 tol to all affected dim's except the .50+/-.03 dim, how far does EDGE D stick out above EDGE E (figure it off the centerline, don't worry abou the clearance between the bolt and the holes)?Min = ? Max= ?
Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and calculate the true position tolerance. Show your calculations. Please note: Dimensions shown is relative to the actual size As drawn 4XØ0500 -0.312 Oe.005(M A BC C Pattern-4 holes # 2 1.000 # 3 +) 1.500 +)
Please refer to the image attached. Study the sheet metal assembly at the top of the image. It consists of two main parts, a flexible tube and reinforcement cap. They are attached with 4 self threading fasteners. Select datum features based on the mating condition. Make sure to note the fit between the parts. Calculate and apply position tolerances using the fastener formulas on the previous pages. Apply other necessary geometric tolerances to ensure assembly and minimize mismatch on outside edges.
The dimensions of the mating parts, according to basic hole system, are given as follows : Hole : 25.00 mm Shaft : 24.97 mm 25.02 mm 24.95 mm Find the hole tolerance, shaft tolerance and allowance.
Based on the part number of the vertical cylinder, look up the manufacturer’s data sheet to determine: Piston diameter Rod diameter Stroke length
Some hole size tolerances are specified as D7, N6, and H8. Where does the print reader find the values for those specifications? (Multiple Choice)a. In a tolerance block located in the upper-left corner of the sheetb. On line at the manufacturers websitec. A supplemental documentd. The are proprietary and not stated
Ex. Find 9 f- 120mm 125mm !30m
3. If there is a 0.10 mm accuracy error for all measured parameters at Instruction 1, determine the true volume of the allen bolt. Also, comment on the difference between volume calculated by measured data and volume calculated by true data.
Compute for the value of the uniformity coefficient with the data shown below. D10 = 0.08 mm D30 = 0.22 mm D60 = 0.41 mm Select one: a. 4 b. 6 c. none of the choices d. 7 e. 5
Given the following G-code, what is the width of the rectangle if a 1/2" end mill is in the tool holder? (assume (0,0,0) is at the lower left, and z=0 is set at the top surface of the workpiece as usual) G20 G90 G28 M06 T1 M03 S1000 GOO XO YO Z-.25 G41 D1 G01 X1 Y1 Z-.25 F3 G01 X5 Y1 Z-.25 F3 G01 X5 Y3 Z-.25 F3 G01 X1 Y1 Z-.25 F3 GO0 X4 YO Z.25 a) 3.5" b) 4.5" c) 3" d) 4" e) 5"

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Complete the needed calculations and enter the needed values in the given table. All problems are for a floating fastener application. A. B. C. Hole dia at Fastener dia Allowable position tolerance at MMC MMC at MMC .189 279 .164 190 .031 .029