Given the following G-code, what is the width of the rectangle if a 1/2" end mill is in the tool holder? (assume (0,0,0) is at the lower left, and z=0 is set at the top surface of the workpiece as usual) G20 G90 G28 мо6 T1 M03 S1000 GO0 XO YO Z-.25 G41 D1 G01 X1 Y1 Z-.25 F3 G01 X5 Y1 Z-.25 F3 G01 X5 Y3 Z-.25 F3 G01 X1 Y1 Z-.25 F3 GO0 X4 YO Z.25 a) 3.5" b) 4.5" c) 3" d) 4" e) 5"

Given the following G-code, what is the width of the rectangle if a 1/2" end mill is in the tool holder? (assume (0,0,0) is at the lower left, and z=0 is set at the top surface of the workpiece as usual) G20 G90 G28 мо6 T1 M03 S1000 GO0 XO YO Z-.25 G41 D1 G01 X1 Y1 Z-.25 F3 G01 X5 Y1 Z-.25 F3 G01 X5 Y3 Z-.25 F3 G01 X1 Y1 Z-.25 F3 GO0 X4 YO Z.25 a) 3.5" b) 4.5" c) 3" d) 4" e) 5"

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The tool starts at point P1 (X-50.0,Y-15.0) and goes the around part counterclockwise. It then goes back to P1. Write the part program with I and J. Dia 16 mm End Mill R15 70 8 P1 0,0 -120- 20 10
Sketch the 2D figure of cover using AutoCAD and mention all the dimensions, colour the hatched lines if there any. 80 Dia 8 42 106 22 42 16 24 R 16 R 80 Cover
Write all the commands steps of the AutoCAD software to reach the drawing of the figure below all dimensions in mm -80- -70 -50 040- -Ø120 -260 10. 120- 60 40 293.2- -D120- SECTION A-A Your answer 120- -090- -2X45° R30 93.2- 10 -2X45 090 120
I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
I am sorry but your values when plugging in are not the correct values. Not too sure where your values are from but can you please redo the question using the given values in this problem and not from a different problem please? (example, height is not 29, it is 22) all values do not correlate to this problem. I was also told when finding the area of triangle to use (1/2)*b*h*Ad^2 and not 1/36*b*h*Ad^2 Find the moment of inertia and radius of gyration of the section of this bar about an axis parallel to x-axis going through the center of gravity of the bar. The bar is symmetrical about the axis parallel to y-axis and going through the center of gravity of the bar and about the axis parallel to z-axis and going through the center of gravity of the bar. The dimensions of the section are: l=55 mm, h=22 mm The triangle: hT=12 mm, lT=19 mm and the 2 circles: diameter=8 mm, hC=6 mm, dC=8 mm. A is the origin of the referential axis. Provide an organized table and explain all your steps…
Draw the three projections of the body in Figure 1- using AutoCAD 1-Do not write the dimensions on the drawing 2- Draw with the same measurements as shown 3 -Show graphics properties At least properties are required for the circle and arc R10 R20 40 35 55 -1- JSI 9.
Draw front and right-side views of the following object with a completed dimensions. Draw in scale 1:1 on A4 sheet. (Problem is taken from "Graphics for Engineers' by Earle) 78 What can we learm from the drawlng ? 1. The dimension note M10x1.5 means that the hole is a threaded hole. R16 O 16, 2 Holes The letter 'M' means that the threads are made by following a metric thread system. The number "10" Is the major dlameter of the hole and the number 1.5 is the pitch of a thread. However, for coarse threads, it is a common practice to omit specifying the pitches. For example, a note M10 means the pitches of the thread is 1.5 mm. In this book, the pitch is specified in order to facilitate drafting. 2. Drawing symbol of a threaded hole is shown below. - Thin Ine (4H pench The ends of this arc does not meet together but approximately 90 degs, apart. Object Ihe (2i pencil .major dlameter pich2 M10x1 5 3. The circular projection surface at a threaded hole that is raised from a cylinder is…
finishing the program of the part by using SKY CNC system format R4 2x45° 28 50 60 75 040 032 024
Write a G-Code Program for the part given below. 10 20 40 30 R9 R20 R8 11,98 80 Start Re R7 SS
Draft and annotate the 2D sketch of cover using AutoCAD and mention all the dimensions. Colour the hatched lines which are inside the curve 8R 6 holes 8 Dia 62 Dia 18 R 3 holes 20 Dia 110 Cover 40 Dia 100 R
Locate all the centros from the 6 bar linkage shown below. Show the centro polygon step by step and name each centro found through the mechanism. Ks = 1 inch : 1 foot Kv 1 inch 16 fps Mechanism 1: Dimension in inches G Tek 2 3 G K 1.0000 1.5000 3.5000 94° G K 2.5000 2 45° 1.0000 3 1.0000 2.0000 - 01.0000
pls box ur answer do quick