Calculate the maximum stress affecting a bolt by specifying which Bolts will have the maximum stress if a load of F=61 kN is applied to the specified point, taking into account the dimensions given in the figure below.

Calculate the maximum stress affecting a bolt by specifying which Bolts will have the maximum stress if a load of F=61 kN is applied to the specified point, taking into account the dimensions given in the figure below.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.10P: Three round, copper alloy bars having the same length L but different shapes are shown, in the...

See similar textbooks

Related questions

Q: Specifications: M20 Bolts in standard holes. Nominal hole diameter = 22mm Effective Hole diameter =…

A: given : norminal hole diameter=22mmeffective hole diameter =normal hole diameter +2 mmarea of steel…

Q: 3. A bar of 12 mm diameter gets stretched by 3 mm under a steady load of 8 kN. What stress would be…

A: Given data: d=12 mm=0.012 mδL=3 mm=0.003 mW=800 NP=8 kN=8000 NE=200 kN/mm2h=80 mm=0.08 m Need to…

Q: Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint.…

Q: As shown in the figure, a bolt with a diameter of 10 mm is affected by three separate forces in…

Q: A 222 mm-diameter bolt having a diameter at the root of the threads of 18.6 mm is used to fasten two…

Q: Write legibly, provide manual step by step solution, and diagram for below given problem. A 100 mm…

Q: 1.) A long flat steel bar 6 in. wide and 3/8 in. thick has a 2.5 in. diameter circular hole…

Q: The 10-mm thick component in the figure is designed with a fillet and a hole. The load varies from…

Q: From the figure below, what is the rolling resistance from each wheel if they share to carry a…

A: Given data: W=18.7 kN Need to determine the rolling resistance from each wheel and required Force…

Q: For the following configurations shown in figure below, determine the ratio of the maximum shear…

A: Solution: Maximum shear stress is given by, Solid tube,…

Q: 2. The lap joint in the figure is made using a 30 mm diameter bolt. The outer plates are 5 mm thick,…

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 × 2-…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: The figure shows a welded-arm. The arm is welded using ! normal yield strength of 393MPa. If the…

A: Given data: The given weld size from the figure is The radius of the weld is

Q: The diameter of the pin to be used at the B point in the brake mechanism in the figure is dB = 12 mm…

Q: Solve the problems below: 1. The lap joint shown in Fig. P-126 is fastened by four 3/4 -in.-…

Q: A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R1and R2. The…

Q: P 5 kN 150 mm 300mm 70° B 10 mm- в 6 mm

A: Given, σy-B = 60 MPaσy-CD = 100 MPaSF = 2t = 6 mm Consider below FBD for the given question:

Q: The five-bolt connection shown in in the figure must support an applied load of P = 300 kN. If the…

A: To obtain the required diameter of the bolts, we need to understand that the shear force is resisted…

Q: high pressure boiler accumulator are fixed using a number of bolts of M16 × 2- C, grade 5.8, with…

Q: A hollow aluminum cylinder made of 2014-T4 has an outside diameter of 2.50 in. and a wall thickness…

A: Given data for aluminum cylinder 2014-T4

Q: For the figure shown, use P = 100 kN, L = 300mm, 5 = 100 mm and S2 = 180 mm. Assume the diameter of…

A: Ans: 14. b 15. d 16. a

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

Q: Q2/ The 2-mm-thick bar shown in the figure below is loaded axially with a constant force of 12 KN.…

A: To Find: Where the crack be more likely to initiate. Given: The thickness of the bar is t=2 mm1…

Q: 1: Pin B can support a load up to 8 kN, roller A can support a load up to 4 kN. Calculate the…

A: ∑MB=04×2×w-NAsin 30°×3sin 30°-NAcos 30°3cos 30°+4=0NA=1.23w∑Fx=0NAsin 30°=BxBx=0.61w∑Fy=0 By+NAcos…

Q: Prove the formula for Hoop stress and longitudinal stress and also explain poisson ratio.

A: Given Data⇒ Hoop Stress Longitudinal Stress Poisson ratio

Q: Q1: For the problem in Figure (1), determine maximum allowable load P such that maximum flexural…

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

Q: Suppose the load in the figure below is 2 kN. Further suppose that the distance between the load and…

A: Given : P= 2kN The distance between load and centroid is 1.3 m The horizontal distance between bolt…

Q: A rectangular plate with a hole is shown in fig that carries a tensile load. Stress value calculated…

A: Given that A rectangular plate with a hole is shown in fig that carries a tensile load. Stress…

Q: Figure Q16 shows a simple bolted single lap joint plate and a simple bolted double lap joint plates…

A: Given Data: The tensile load applied to the lap joint is, P. The diameter of bolt is, d.

Q: Q5. The Figures below shows a simple bolted single lap joint plate and a simple bolted double lap…

Q: A 20 mm diameter bet having a diameter at the toot ef the thread of 18.6 mm is used to fasten two…

Q: The lap joint shown in Fig. P-126 is fastened by four 4-in.-diameter rivets. Calculate the maximum…

Q: Two steel plates grade 300 having the same dimensions (250mm width x 25mm depth) are joint using…

A: Given data, Applied force, F = 950 kN = 950000 N Shear strength of the bolt, τs,bolt=0.6×830=498 MPa…

Q: The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the…

Q: A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a…

Q: 3. Problem 2: The lap joint is fastened with four rivets. If the working stress is 14 ksi (kips per…

Q: Exercise: 06 For the system given in figure, determine force required to drive a 1000 N load. 400 mm…

Q: An eye bolt carries a tensile load of 20kN.Find the size of the bolt(in mm), if the tensile stress…

Q: 1. The lap joint shown in Fig. P-126 is fastened by four 3/4 -in.- diameter rivets. Calculate the…

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 × 2 -…

A: Any action that can change the state of motion is force. Force is described by its magnitude, point…

Q: A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric…

A: Draw a diagram showing the centroidal axis and neutral axis in the cross-section. Here, CA is the…

Q: PROBLEM 3 Two shafts are being connected by a coupling which is held together by four 3/4-in…

Q: 4) The C-clamp shown below has rectangular cross-section A-A that is 33 mm tall by 12 mm wide and…

Q: The figure below shows a boat propeller mounted on a drive shaft with a 7 mm diameter (d)…

A: Given: Diameter of the pin d=7mmDiameter of the drive shaft D=69mmYield stress σy=427MPaUltimate…

Q: A cylinder head for steam engine is held by (14) bolts. The effective diameter of the cylinder is…

Question

Please answer this question.

Calculate the maximum stress affecting a bolt by specifying which Bolts will have the
maximum stress if a load of F=61 kN is applied to the specified point, taking into account the
dimensions given in the figure below.
300 -
12
18
MIS
F=60 kN
300
75
-90 --|--90 -- 60
450
2----

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Agui - 4550/2 =2276 two plates each with thickness t - 16 mm are bolted together with 6-222 mndia. bolts firming alap Joint Bolt spacing are follows St- $40mm S2 - 80mm, S3=150mm effective bolt hole dia. is 25mm A36 is used. Compute the allowable tensile Strength P t = 16 mm &t 52 747₁ 0 O O 40 60 80 40 +=16mm S-400 $3-100 S2-40 7 @ 4umm P
S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B and D pins (B single cut D double cut), the thickness t of the BD bar. (Safety Cat.(S)=2, T = 250 Nmm2 o -350 N/mm2) 40.a mm 300 mm ТАКE a-9,6 60.a mm 50 mm D Yatağı 100 mm C t mm |F=100 kN
4. Determine the design stress for bolts in a cylinder cover where the load is fluctuating due to gas pressure. The maximum load on the bolt is 50 kN and the minimum is 30 kN. The load is unpredict- able and factor of safety is 3. The surface of the bolt is hot rolled and the suface finish factor is 0.9. During a simple tension test and rotating beam test on ductile materials (40 C 8 steel annealed), the following results were obtained : Diameter of specimen =12.5 mm; Yield strength= 240 MPa; Ultimate strength= 450 MPa; Endurance limit = 180 MPa. [Ans. 65.4 MPa]
In the clevis shown in Fig. 1-11b, the minimum bolt diameter (d=22mm) and the minimum thickness of each yoke(t=10mm) without exceeding a shearing stress of 83MPa and a bearing stress of 138MPa. -Find the support load (P=?) Y. Figure 1-11b
In the clevis shown in Fig. 1-11b, find the minimum bolt diameter and the minimum thickness of each yoke(t=10mm) that will support a load P = 63KN without exceeding a shearing stress of 38MPa and a bearing stress of 138Mpa. 1' Figure 1-11b
need 4 & 5 Q1: The load on a bolt consists of an axial pull of 10 kN together with a transverse shear force of 5 kN. Find the diameter of bolt required according to1 Mavimumneinialtracsthe ar ncory, viaa distortion energy theory. intheory; 4. Maximum strain energy theory; and 5. Maximum
4 @ 40 mm P 2 @ 60 mm Problem 02 Based on the bolt capacity, determine the required number of 20 mm Ø A490F bolts needed to develop the full strength of the steel plate in Problem 01 if P= 250 kN. Assume that the surface is Class A and the hole size is standard. Use LRFD
(11) The figure shows a connection that employs three SAE grade 5 bolts. The tensile shear load on the joint is 5400 lbf. The members are cold-drawn bars of AISI 1020 steel. Find the factor of safety for each possible mode of failure. (Ans./ 3.26, 5.99, 3.71, 5.36) in- 글im 16 UNC in I in -24 in-
9-21 The figure shows a weldment just like that for Probs. 9-17 to 9-20 except there are four welds to instead of two. Find the safe bending force F if the allowable shear stress in the welds is allow 9-24 Problem Number b 9-21 50 mm 150 mm 9-23 50 mm 150 mm d 50 mm 30 mm h 5 mm 5 mm Tallow 140 MPa 140 MPa Problems 9-21 to 9-24
1-69.M Figure P1-69 shows a bolt subjected to a tensile load. One failure mode would be if the circular shank of the bolt pulled out from the head, a shearing action. Compute the shear stress in the head for this mode of failure if a force of 22.3 kN is applied. Applied force Shear area Reaction force on underside of head Cylindrical shear area 19.0 mm 8.00 mm -12.0 mm M12 x 1.75 thread
150- 18 F = 25 KN 25 200 25 + 25 € 100- -25 25 50 4 For the bracket and loading condition shown above, determine the smallest size Grade 8.8 metric bolt needed to hold the bracket in place that will still provide a minimum factor of safety of 2 versus the proof strength of the bolt. Assume coarse threads. Neglect the vertical shear on the bolts. All dimensions are in millimeters.
Calculate the maximum tensile stress developed in a 1/4-20 bolt (Major dia = 0.2500" and Root dia = 0.1959"), 3" long, and a head height of 0.1875", if it is subjected to a load of 426 lbs.