Calculate the average shear stress in MPa of the pins B and C on the frame shown in the figure. Note that these pins are subjected to double shear and have a diameter of 0.5 inch. 500 Ib 4 ft 2 ft| 2ft 4 ft 500 N

Calculate the average shear stress in MPa of the pins B and C on the frame shown in the figure. Note that these pins are subjected to double shear and have a diameter of 0.5 inch. 500 Ib 4 ft 2 ft| 2ft 4 ft 500 N

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.9.7P: The cross section of a slit square tube of constant thickness is shown in the figure. Derive the...

See similar textbooks

Related questions

Q: Water with a velocity of 7.83 m/s flows through a 126 mm diameter pipe. Solve for the mass flow rate...

Q: 8. 7. 10 is 20 25 10 15 20 25 9. 10. 6 7 8 6. 10 15 20 25 10 15 20 25 11. 12. 2 3 4. 5 6 8 9 2 3 10 ...

Q: AT-Shaped beam has a length of L- 35 m is acted upon by the distributed load as shown which has a ma...

A: Given: Length of the beam→L=3.5 m Maximum intensity of the load→w=597 Nm the load is uniform variabl...

Q: Provide a clear and complete solution for below problem. A rigid vessel has an initial condition o...

Q: 19. Consider two-phase flow in a tube of diameter 0.5 in and length 3 ft. For P = 1000 psia, m= 0.35...

Q: Water at 60F is flowing through a 3-inch inside diameter smooth horizontal pipe. If the Reynolds num...

Q: 1. Find the transfer function, c(s) - x,(4)/F(), for each of the system shown In the figure below. a...

Q: P1-1. Draw a free-body diagram of the ring at A and identify each force. 30 45° 200 N 500 N (c)

A: Draw the free body diagram at A and identified force at A.

Q: What is the rate of flow of water passing through a pipe with a diameter of 1944 mm and a speed of 1...

Q: B FIGURE 1. Q;B =1 in: BC = 3 in.; wz = 1, constant. Find the absolute linear acceleration for point...

A: Answer: The absolute linear acceleration of point C is 0.7071 m/s2.

Q: Q1) In the arrangement given in Figure Q1, weight of Q is 1000 N and weight of the platform P is 200...

Q: 2. A sump pump turning at 1600 rpm provides a water discharge of 9gpm againts a head of 18ft. Comput...

A: The fundamental rule of activity of divergent siphons is - force vortex stream. This implies, when a...

Q: Liquid oxygen is stored in a thin-walled, spherical container 0.8 m in diameter, which is enclosed w...

Q: Design a 1000 mm wide end-fed sheeting die wi film. For the solution of the problem, assume a mani: ...

A: Wide=1000mLand gap=1mmDiameter of Manifold =15mmLength =50mm To-Find:- Design

Q: The beam shown below has a cross section of channel shape with width b-400 mm and height h=80 mm, th...

A: Answer: (a) The maximum tensile stress is 64.68 MPa. (b) The maximum compressive stress is 16.36 MPa...

Q: An open test tube at 293 K is Water at 20°C is being pumped from a tank to an elevated tank at the r...

A: Given dataFlow rate of water = 5 x 10-3 m3/sPipe diameter = 4 inch = 101.6 mm = 0.1016 mPump efficie...

Q: 15. The partial pressures of a mixture of gases are 20 kPa (N2), 60 kPa (O2), and 80 kPa (CO2). If 2...

Q: What is the importance of low flow protection system in a centrifugal pump? What are the resistance...

Q: calculate how many kWh of the output power is generated during an hour by this cycle.

A: Given that: For a Carnot cycle, working fluid is air. 1 kg of mass is flowing. High temperature is 5...

Q: Two concentric spheres of diameter D = 0.7 m and D2 = 1.2 m are separated by an air space and have s...

Q: Determine the magnitude of the acceleration of point A at the instant shown. Express your answer to ...

A: Given Dataα=7rad/s2ω=4rad/sr=0.1m

Q: An impulse turbine operating at a net head of 2000 ft uses a Pelton wheel of diameter 12 ft and a je...

A: GivenH=2000ft=609.6md=12ft=3.6576mA=5in2=0.00064516 m2Cv=0.94deflected angle φ=165o

Q: 2. Determine the shearing stress in each of the four walls of a portion of a structural aluminum tub...

Q: A compressible air inside an instrument tube is flowing at 350 m/s at standard sea level. The condit...

A: Given data Velocity at section 1 = 350 m/sPressure at section = 1 atm = 101325 PaArea of section 1 =...

Q: In the diagram below, a force P of 750 N is applied to the 350 kg block. Find the acceleration of th...

Q: Two steel sheets of 1.5 mm thickness are spot welded in a lap joint with a current of 10,000 A for 0...

A: Given that, Thickness of steel plate, t=1.5 mm,I=10,000 A,t=0.15 second,Effective resistance, R=150 ...

Q: Draw the Ts/Ph Diagram A 50-ton vapor compression refrigeration system is to evaporate R-12 at -20°C...

A: Solution: Given Data: Q=50 ton×3.52=176 kW c=0.1 D = L

Q: Velomobile Characteristics Mass: 29 kg in addition to the rider Aerodynamic drag: F = 0.0492 V (Newt...

A: Disclaimer: Since you have posted multiple questions we will solve the first question for you. If yo...

Q: The box beam shown in Figure P8.63b has dimensions of b=80mm, d=120mm, and t=8mm. A downward concent...

Q: A jet impinges on a splitter block. The Incoming jet is horizontal and hasa flow rata of Q = 8000 cm...

Q: In a conventional refrigeration cycle which uses Freon-12 as the refrigerant, the temperature of th...

Q: Calculate the Magnitude and angle of the Resultant Force R from the following 2 vectors mathematical...

A: Given data as per question F1=2 grams = 2×0.00980665 =0.0196133 NAngle=200F2=3 grams =3×0.00980665...

Q: QUESTION 5 Which of the following bodies has the largest kinetic energy? O 1. Mass 3M and speed V O ...

Q: If given that the hydraulic radius is 1.3 mm and that the roughness,ε is 0.000015 m calculate the re...

Q: The sports car starts from rest and accelerates with its drive wheels slipping as it does. The kinet...

A: Given data, Mass of the car, m = 2000 kg Kinetic coefficient of friction, μk = 0.35 Only driver whee...

Q: Water with a velocity of 3.69 m/s flows through a 127 mm diameter pipe. Solve for the weight flow ra...

Q: 6.13 Four identical particles are placed at the points O, P, Q, R of Fig. P5.10. Determine t radius ...

Q: Two bodies radiate heat to each other. One body is at 30 C and the other at 300 C. The emissivity is...

Q: a fluid in a fire hose with a 30.2 mm radius, has a veloctiy of 0.48 m/s. solve for the power, hp, a...

Q: At a proposed hydroelectric power plant site, the tailwater elevation is 490m. The estimated energy ...

A: HYDRO POWER PLANT It is a reservoir of water placed near to turbine and used to avoid the water hamm...

Q: 5. Two shafts (G = 50 GPa) with different diameters are bonded to a disk in the middle. The ends A a...

Q: Wind direction: a. Assuming that the weather system shown on the North P=1atm map to the right has j...

A: a) et streams are relatively narrow bands of strong wind in the upper levels of the atmosphere. The ...

Q: The acceleration of A is 3.5 m/s dovwnward and the acceleration of Cis 2.3 m/s upward. Find the acce...

Q: 3. Consider the drawing below. a. Find I, b. Find Ix

A: To find Iy and Ix

Q: (a) Replace the loading acting on the beam by an equivalent resultant force FR and couple moment (MR...

A: From varignons theorem can replace the the loading of beam into single force.

Q: The Crodge Cram truck, which is manufactured in Outer Elbonia, has an engine with a displacement (in...

Q: A vat contains a mixture of oil and water. The water forms a lower layer which is 0.8 m deep, and ab...

Q: Consider a test specimen with the following material properties: E = modulus of elasticity = 30 × 10...

A: Given : To find : Stress - strain response

Q: Liquid oxygen is stored in a thin-walled, spherical container 0.8 m in diameter, which is enclosed w...

A: Given data: di=0.8 mTo=280 Kdo=1.4 mTi=95 Kε=0.05hfg=2.13×105 J/kg Need to determine the mass flow r...

Q: 1. The specific weight of water at ordinary pressure and temperature is 62.4 lb/ft3. The specific gr...

Concept explainers

Basic Thermodynamic Processes

The word 'thermodynamics' can be divided into two words, 'thermo' and 'dynamics'. The word thermo deals with the heat and thermal phenomenon, whereas dynamics deals with forces or external agent that drives the heat flow or aids in the motion of heat.

Question

Include FBD and full solution please

Thank you!!!

Calculate the average shear stress in MPa of the pins B
and C on the frame shown in the figure. Note that these
pins are subjected to double shear and have a diameter
of 0.5 inch.
500 Ib
4ft
2 ft 2 ft
500 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Continuous cable ADS runs over a small Frictionless pulley at D to support beam OABC that is part of an entrance canopy Tor a building (see figure}. Assume that the canopy segment has a weight it' = 1700 lb. (a) Find the required cross-sectional area of cable ADB if the allowable stress is 18 ksi. (b) Determine the required diameter of the pins at O. A, R and D if the allowable stress in shear is 12 ksi.
Cable DB supports canopy beam OABC as shown in the figure. Find the required cross-sectional area of cable BD if the allowable normal stress is 125 MPa. Determine the required diameter of the pins at 0, B, and D if the allowable stress in shear is 80 MPa. Assume that canopy beam weight is w = 8 kN. note The pins at 0, A, D and D are in double shear. Consider only the weight of the canopy; disregard the weight of cable DB.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A square steel tube of a length L = 20 ft and width b2= 10.0 in. is hoisted by a crane (see figure). The lube hangs from a pin of diameter d that is held by the cables at points A and B. The cross section is a hollow square with an inner dimension b1= 8.5 in. and outer dimension b2= 10,0 in. The allowable shear stress in the pin is 8,700 psi. and the allowable bearing stress between the pin and the tube is 13,000 psi. Determine the minimum diameter of the pin in order to support the weight of the tube. Note: Disregard the rounded corners of the tube when calculating its weight.
A cylindrical tank subjected to internal pressure/? is simultaneously compressed by an axial force F = 72 kN (see figure). The cylinder has diameter d = 100 mm and wall thickness t = 4 mm. Calculate the maximum allowable internal pressure /?max based upon an allowable shear stress in the wall of the tank of 60 MPa.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.