Provide a clear and complete solution for below problem. A rigid vessel has an initial condition of 80oF and 16 psig. If the vessel is heated until its temperature increases to 300oF, find the final pressure in psig. A. 14.56 B. 98.34 C. 28.50 D. 18.34

Provide a clear and complete solution for below problem. A rigid vessel has an initial condition of 80oF and 16 psig. If the vessel is heated until its temperature increases to 300oF, find the final pressure in psig. A. 14.56 B. 98.34 C. 28.50 D. 18.34

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 6RQ: One British thermal unit will raise the temperature of _____ 1b of water _____F.

See similar textbooks

Related questions

Q: An aquarium 7 m lc the hydrostatic pre the hydrostatic for

A: Solution: 7x5x4 aquarium full of water To determine: hydrostatic pressure on the bottom force on bot...

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses...

Q: The addition of damping to an undamped spring-mass system causes its period to increase by 50 percen...

A: Given: The time period, Td = 1.5Tn

Q: single square-thread screw has an input power of 3 kW at a speed of 1 rev/s. The screw has a diamete...

Q: ratio of external to internal diameter 2:1. Calculate (a) the hydraulic efficiency, (2) power, and (...

A: Given: Q=1500 l/s H=6.2 m D2/D1=2 D2=1.2 m N=210 rpm A=0.65 m^2 To determine: (a) the hydraulic eff...

Q: Why are seals used in mechanical assemblies? Explain diaphragm seals with a neat sketch?

A: A mechanical seal is simply a method of containing fluid within a vessel (typically pumps, mixers, e...

Q: 5. Two shafts (G = 50 GPa) with different diameters are bonded to a disk in the middle. The ends A a...

Q: The diameter of the discharge pipe of pump is 15 cm and that of intake pipe is 20 cm. The pressure g...

A: In the hub stream siphon, the impeller cutting edges guide the liquid pivotally. In this siphon, the...

Q: A water pump is required to deliver 10 m2/min of water at a temperature of 27°C and the pressure is ...

A: Answer: The power required to drive the pump is 46.6757 kW.

Q: An aluminum strut 2 m long has a rectangular section 20 mm by 50 mm. A bolt through each end secures...

Q: Part A Due to slipping, points A and B on the rim of the disk have the velocities v = 7.2 ft/s and v...

Q: Describe and differentiate the other three types of microtome other than hand microtome.

A: A microtome (from the Greek mikros, meaning “small”, and temnein, meaning “to cut”) is a tool used t...

Q: 1) A cable is attached to a 0.5 kg block that slides over the smooth rigid horizontal rod AB. The di...

A: Draw the free-body diagram of the block.

Q: An 8-pitch pinion with 18 teeth mates with a gear having 64 teeth. The pinion rotates at 2450 rpm. C...

Q: Briefly explain the working of one typical CNC Machining Centre and its operations.

A: A machining center can be defined as a sophisticated CNC machine tool controlled by a computer runni...

Q: A) The velocity of the ball required to maintain the arc B) The tension in the rope

Q: | In a certain device using water as the working fluid, superheated vapor at state 1 flows in, liqui...

Q: A spherical particle of diameter D1 = 10 mm is suspended by a thin wire within a cylindrical tube of...

Q: P1-2. Write the two equations of equilibrium, EFx = 0 and EFy = 0. Do not solve. 20 450 N 30 40° 300...

Q: A compound bar consisting of bronze, aluminium and steel segments is loaded axially as shown in figu...

Q: Explain the Effect of the action of forces on rigid bodies

Q: A car initially going 68 ft/sec brakes at Q1) a constant rate (constant negative acceleration), comi...

A: Car's initial speed, u = 68 ft/sec, Time taken to stop the car is, t = 7 sec, From the equation of ...

Q: ᴛʜᴇ ᴅᴇɴꜱɪᴛʏ ᴏꜰ ᴛʜᴇ ꜰᴏʟʟᴏᴡɪɴɢ ᴘᴜʀᴇ ᴍᴇᴛᴀʟꜱ, ᴇxᴘʀᴇꜱꜱ ʏᴏᴜʀ ᴀɴꜱᴡᴇʀ ɪɴ ᴋɢ/ᴍ^3. (Show solution in manner) ...

Q: How does air-over Hydraulic brake system work

A: Air brakes are much easier to attach than hydraulic brakes, and using air rather than hydraulic ...

Q: PROBLEM 2.0: In a conventional refrigeration cycle which uses Freon-12 as the refrigerant, the tempe...

A: Given data, Refrigerant is R-12. Evaporator temperature, Tevp = -20 °C Condenser pressure, Pcond = 1...

Q: |Part of a refrigeration system operates at steady state with Refrigerant 22 as shown in the figure ...

A: a) At state 1 , saturated liquid at 120 lbf/in2. from the R-22 table : Tsat=61.942 °F

Q: Time left 0:59:02 Which of the following statement(s) is correct? Oa. Paralleogram Law can be used t...

A: Parallelogram law cannot be used to find Resultant of more than two vectors. It is used to find Resu...

Q: This prelab question is about the experimental setup shown in the Lab Manual as Figure 1 for Experim...

A: In theory we assume ideal conditions (that are not practical or applicable in real world). Hence dur...

Q: Write the two equations of equilibrium, EFx = 0 and EFy !3! %3D

Q: A power station has to supply load as follows: Draw the load curve Draw the load-duration curve ...

A: Given: LOAD CURVE:

Q: Chlorine gas at 20 degree Celsius is under a pressure of 481 kpa. Assume a gas constant of 117n-m/kg...

Q: t 25oC, one block was blown by wind at 65oC as shown in Figure 1. The block has dimension of 9m-long...

A: Given dataTemperature of block = 25°CTemperature of wind = 65°CDimensions of block = 9 m long and 4 ...

Q: The following statements deal with the factors that affect solubility for solids and gases. For each...

A: To find :- Reason of statement

Q: Give an example of machine tool accidents and explain the safety violated?

A: Proper procedure should be followed while operating machine tools. Most machine tools, involve vario...

Q: Two bodies radiate heat to each other. One body is at 30 C and the other at 300 C. The emissivity is...

Q: The figure illustrates the nonpermanent connection of a steel cylinder head to a grade 30 cast-iron ...

A: Given: The number of bolts, n = 73 The effective sealing diameter of gasket, D = 0.9 m The maximum c...

Q: The table shown below describes a 6-bar linkage. Dimension Description Link 1 (0:O4) 2 (O2A) 3 (ABC)...

A: Calculate the number of centros in 6 bar linkage. I=nn-12=66-12=15

Q: E moment of 5 kip-ft. neutral axis relative to the bottom of the cross section. 3 in.

Q: A 50-ton vapor compression refrigeration system is to evaporate R-12 at -20°C and to condense it at...

A: Vapour-compression refrigeration or fume pressure refrigeration framework (VCRS),[1] in which the re...

Q: 5 Second conditional T82 Rewrite the sentences with the second 1 I can't take you to the airport bec...

A: Hi and thank you for the questions. We are authorized to answer three subparts at a time, since you ...

Q: Calculate the work required to move a mass “m” against A Force Field F = 5Ux + 7Uy along the indicat...

Q: liquid having a density of 801 kg/m3 and a viscosity of 1.49x10-3 Pa.s is flowing through a horizont...

A: Given Density = 801 kg/m3 Viscosity = 1.49x10-3 Pa.s Velocity, v = 4.57 m/s Find Friction l...

Q: 45° FR F 75° 60 200 lb Using the sine rule, we have: O a F- 200lb Ob F- 273lb Oc F=189lb O d. F= 245...

Q: The cylinder of a portable hydraulic riveter is 220 mm in diameter. The pressure of the fluid is 14 ...

A: GivenD=220mmP=14N/mm2=14MPaσp=105MPa

Q: (2) A connecting link is as shown, except that there is a -in. radial hole through it at the center ...

Q: 19. Consider two-phase flow in a tube of diameter 0.5 in and length 3 ft. For P = 1000 psia, m= 0.35...

Q: 2. The stresses shown in the figure act at a point in a stressed body. Using the equilibrium equatio...

Q: 1 Constraints: A. do not set property limits B. are attributes or properties used to maximize the fr...

A: Constraints ****As per our company policy we are supposed to do only 1 question if you need the res...

Q: a, Describe the raw material used for this part, b, Manufacturing procedures of part and assembly se...

A: Disclaimer: Since you have posted a question with multiple subparts, we will solve the first three s...

Q: Draw the Ph/Ts Diagram. In a conventional refrigeration cycle which uses Freon-12 as the refrigerant...

Concept explainers

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.

Question

Provide a clear and complete solution for below problem.

A rigid vessel has an initial condition of 80^oF and 16 psig. If the vessel is heated until its
temperature increases to 300^oF, find the final pressure in psig.

A. 14.56 B. 98.34 C. 28.50 D. 18.34

Answer: C

4. A rigid vessel has an initial condition of 80°F and 16 psig. If the vessel is heated until its
temperature increases to 300°F, find the final pressure in psig.
A. 14.56
Answer: C
B. 98.34 C. 28.50 D. 18.34

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A closed vessel contains air at a pressure of 140 kPag and a temperature of 20°C. Find the final absolute pressure in KPA if the air is heated at a constant volume to 100°C. The atmospheric pressure is 28 in. Hg. a. 298.93 b. 300.93 c. 278.93 d. 288.93
A sealed rigid vessel has volume of 1 m3 and contains 2 kg of water at 100°C. The vessel is now heated. If a safety pressure valve is installed, at what pressure, in bar, should the valve be set to have a maximum temperature of 200°C? Select one: O a. 534.22 O b. 4.313. O c. 5.34 O d. 431.3
5. A gas cylinder of volume 'V' and radius 'r' contains 1.00 mol He at a pressure PHe and 1.00 mol Ar at a pressure of PAr, and both are at a temperature T = 298.0K. At the top of the cylinder is a disc with a radius 'r' that is permeable to He but not Ar. The disc is pushed to the half volume mark. 1. How much work is required for this process to be conducted isothermally and reversibly? 2. How much does AG, AH and AS change for this process? Semi-permeable disc Ar Ar Не Не Volume = V V/2 V/2
Volume 0.05 m3 while the piston is attached with the pinin a cylinder with 200 kPa pressure and 300 Kthe temperature is. As a result of heat transfer from the environment, the pressure is 0.4 MPa, the pin breaks, and when the system becomes thermodynamically balanced, its volume is 0.1 m3. Area of piston 0.05 m2, piston and masses on 150 kg and atmospheric pressure102 is KPA. a)Find the temperature at the moment the pin breaks. b)Calculate the pressure and temperature after the pin breaks and reaches the equilibrium position.
1. An automobile tire is inflated to 32 psig pressure at 50°F. After being driven the temperature rise to 75°F. Deter- mine the final gage pressure assuming the volume remains constant.
1. Water in a hydraulic press, initially at 137 kPa absolute, is subjected to a pressure of 116,280 in the volume of the KPa Absolute. Using Ep = 2.5 GPa, determine the percentage decrease water.
1. Consider the following schematic of a power plant (operating in what is called a 'Rankine Cycle') Turbine Steam generator Condenser Coling water Economiaer The power plant control room reports that the plant is operating continuously at the following peak load conditions: a. Power to pump = 300KW b. Rate of steam flow = 25 kg/s c. Cooling water temperature at condenser inlet = 13 C d. Cooling water temperature at condenser outlet = 34 C Additionally, the following measurements were made at various points in the piping connecting the power plant components Data Pressure Temp. Quality enthalpy Specific Velocity (kJ/kg) point (kPa) volume (m/s) (m3/kg) (C) (x) 1 6200 2 6100 43 5900 177 ---- 4. 5700 493 ----- 5 5500 482 ----- 6 103 0.94 183 7 96 43 -----
It is said that independent temperatures are held at 273 K in a volume of 11.35 dm3, and its capacity of molar heat at 29.4 J K^-1 mol^-1 Cp. If the constant temperature 273 K is reversely compressed to it’s half volume. a. What has changed with the U of the gas? b. What is the gas's final pressure. c. Compute the work done to it’s system? d. How much heat does the system flow out e. Gas change in H?
An 8cu.ft of gas at 67.4 deg.F decreases its pressure from 82.4 psia to 22.7 psig. If PV=C, find the volume at the end of the process.
5. Two kilogram of certain gas with R = 0.218 kJ/kg-Kundergoes a process and results to the following changes: AH= 2190 kJ, AU = 1460 kl. D. What is the change in termperature?
15. A boiler installed where the atmospheric pressure is 752 mm Hg has a pressure of 12 kg/cm2. Find the absolute pressure, in MPa.
17. The nitrogen gas a volume of 23.4ml in a tube at a 18°C and a pressure of 781mmHg. The next day the volume of the nitrogen was 26.2mL with the barometer still reading 781mmHg. What was the temperature on the second day? a. 67.3915°C b. 27.1701°C c. 52.8385°C d. 68.5611°C