At an operating frequency of 300 MHz, it is desired to use a section of a lossless 50 N transmission line terminated in an open circuit to construct an equivalent load with reactance X = 45 N. If the phase velocity of the line is 0.6c, what is the shortest possible line length (I %3D ) that would exhibit the desired reactance at its input? Answer: l = 60 m

At an operating frequency of 300 MHz, it is desired to use a section of a lossless 50 N transmission line terminated in an open circuit to construct an equivalent load with reactance X = 45 N. If the phase velocity of the line is 0.6c, what is the shortest possible line length (I %3D ) that would exhibit the desired reactance at its input? Answer: l = 60 m

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem 13.8P

See similar textbooks

Similar questions

The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
c) For a transmission line w/characteristic impedance Z0 = 50 W. At some point of the line, a forward wave has the voltage V+ = 10V and backward wave has the voltage V- = 4V. i) Currents of the forward wave and backward wave at that point. ii) Measured voltage and current at that point. d) A transmission line has the following properties: Length, L = 3 m. Characteristic impedance Z0 = 50 W. The load impedance ZL = 100 W. And phase constant b = p/3. Assume the forward voltage at z = 0 is VA =10ejp/4 At z = 3m, calculate: i) Forward voltage and forward current. ii) Backward voltage and backward current. iii) Measured (total) voltage and current across the load
Q) A source of 10 V and frequency 1000 KHz with internal resistance of 10 2 is connected to the sending end of a transmission line which can be represented by a resistance of 70 Q in series with capacitance of 0.001 uF connected across the line at the receiving end. An inductive load of inductance 0.002 H and resistance 100 is connected across the receiving end of the line. Determine the load current.
6-A lossless T.L. has Zo = 100 N and is loaded by an unknown impedance Its VSWR is 4 and the first voltage maximum is A/8 from the load . Find the load impedance .
Paragraph Styles The power factor must be close to in the transmission lines will be reduced To insure that losses D(Ctrl) -
b) A 6052 characteristic impedance transmission line is fed by a DC source of 100V with an internal resistance of 4002. The line is 200m long and has a dielectric constant of 2.25. The load impedance is 12002. Calculate: i. The load reflection coefficient. ii. The source reflection coefficient. iii. What is the voltage at the source terminals just before AND just after 2us?
A Three-phase transposed line is composed of one conductor per phase with flat horizontal spacing of D = 14 meters, as shown in the below figure. The conductors have a diameter of 2.6 cm and a GMR of 1.012 cm. Find the capacitance per phase per kilometer of the line. a C D D 2D Select one: O a 0.0088 microF/Km Ob. 0.0077 microF/Km Oc 1.455 microF/Km Od. None of these
Subject - Design electrical circuits for single phase AC networks Question - Discuss the difference between resonant and non-resoinant circuits. Use equations to explain your answer.
Three lossless lines are connected as shown in the figure below. Determine the input impedance. a/2 2/4 3A/4 Z,,= 500 Z= 1000 Zg= 750 Z= 60-j40 Q "03
The open circuit and short circuit impedance of a transmission line are 200 ohm and 50 ohm respectively. What will be the characteristic impedance of the transmission line?
The corona loss on a particular ac system of frequency 60 Hz is 2 kW/phase per km. The corona loss on the same system in case of DC transmission will be.
The 50 ohm transmission line isterminated with an unknown load. The magnitude of the reflection coefficient is R=0.5.Thedistancebetween the voltage maximum and the load is0.15 lambda. What is the imaginary partof the load impedance?