Assume that both a triaxial shear test and a direct shear test are to be performed on a sample of dry sand. When the triaxial shear test is performed, the specimen fails when the major and minor principal stresses are 80 and 20 lb/in2, respectively. When the direct shear test is performed, what shear strength can be expected if the normal stress is 4000 lb/ft2?

Assume that both a triaxial shear test and a direct shear test are to be performed on a sample of dry sand. When the triaxial shear test is performed, the specimen fails when the major and minor principal stresses are 80 and 20 lb/in2, respectively. When the direct shear test is performed, what shear strength can be expected if the normal stress is 4000 lb/ft2?

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.7P

See similar textbooks

Similar questions

Assume that both a triaxial shear test and a direct shear test are to be performed on a sample of dry sand. When the triaxial shear test is performed, the specimen fails when the major and minor principal stresses are 80 and 20 lbs/in^2, respectively. When the direct shear test is performed, what shear strength can be expected if the normal stress is 4000 lbs/ft^2? Show all work.
Assume that both a triaxial shear test and a direct shear test are to be performed on a sample of dry sand. When the triaxial shear test is performed, the specimen fails when the major and minor principal stresses are 80 and 20 lbs/in^2, respectively. When the direct shear test is performed, what shear strength can be expected if the normal stress is 4000 lbs/ft^2?
Samples of damp sand are tested in direct shear (samples are tested at the in situ water content). The procedure involves two separate tests, with different normal loads for each test. In test one, using a normal loading which causes a compressive stress equal to 50 kPa, the sample is failed at a shear stress equal to 33 kPa. For test two, the normal stress is 80 kPa and the sample shears at a stress of 51 kPa. Use this test data to determine the angle of internal friction and the value of apparent cohesion for this sand.
Question 10 A clay specimen was tested in undrained direct shear, under a normal stress of 50 kPa. The peak shear stress measured was 32 kPa and the critical state shear stress measured was 22 kPa. What is the critical state undrained strength of the clay specimen? Express your answer in kPa, but write only the numeric answer in the text box
8. A cohesionless (c' = 0 kPa) soil specimen was subjected to a consolidated-undrained triaxial test. The total stress path, the deviator stress, and the pwp are shown in the figures below. No scale is intended in the figure of the stress path. a. Determine o'₁ and 0's at failure. [o'₁ = 345 kPa, o's= 140 kPa] b. Determine the effective friction angle (') of the soil. [$' = 25°] C. Determine the 'A' pore water pressure parameter at failure. [A+ = 0.29] 250 -Deviator Stress q (kPa), 200 150 100 50 200 p (kPa) Deviator stress or PW/P (kPa) 5 10 Vertical strain (%) ---PWP 15 20
A series of unconsolidated undrained (UU) triaxial compression tests have been performed on two "identical" clay specimens. The test results are as follows: Test Number Confining Pressure (kPa)| Deviator Stress at Failure (kPa) 102 96 (i) (ii) 1 2 50 100 Plot the total stress Mohr circles for both specimens at failure (indicate the major and minor principal stresses on the plot). Draw the total stress Mohr-Coulomb failure envelop (i.e., the "p=0" envelop). Estimate the undrained shear strength.
In a direct shear test on a specimen of cohesionless soil (sand), the vertical normal stress on the specimen is 210 kPa and the horizontal shear stress at failure is 135 kPa. You may assume the uniform stress distribution within the failure zone. a) determine the magnitude and direction of the principal stresses at failure using a Mohr's circle b) briefly explain whether it's possible to determine the magnitude and direction of the principal stresses when the material is not failed.
Samples of a dry sand are to be tested in a direct shear test and a triaxial test. In the triaxial test, the sample fails when the major and minor principal stresses are 140 psi and 40 psi, respectively. What shear resistance is to be expected in the direct shear test when the normal load stress equals 5,000 psf?
A sample of sand is sheared in the following manner. First an all around normal stresso 350 kPa is applied to the sample. Next a shear stress is applied to the horizontal pia while the normal stress remains constant. The shear stresses at failure are + 186 kPa. Ihe initial stress and stress condition at failure are shown below 350 kPa 350 kPa 186 kPa 350 kPa 350 kPa ー550 kPa 550 kPa 186 kPa 350 kPa 350 kPa Initial Conditions At Failure Determine the Following: fo A) Assuming c, = 0, draw a failure envelope for the soil. Define the friction angle ( the soil. B) Draw the Mohr's Circle at failure for the test. C) Show the location of the pole. D) Define the maximum and minimum principal stresses at failure. E) Define the normal stress corresponding to the maximum shear stress
A sand sample is subjected to direct shear testing at its normal (in situ) water content. Two tests are performed. For one of the tests, the sample shears at a stress of 3,000 psf when the normal stress is 4,000 psf. In the second test, the sample shears at a stress of 4,000 psf when the normal stress is 6,000 psf. From these data, determine the value of apparent cohesion and the corresponding angle of internal friction.
For a dry sand specimen in a direct shear test box, the following are given: • Angle of friction: 38° • Size of specimen: 2 in. X 2 in. X 1.2 in. (height) • Normal stress: 20 lb/in.? Determine the shear force required to cause failure.
A sand sample is subjected to direct shear testing. Two tests areperformed. For test 1, The sample shears at a stress of 2500 psf whenthe normal stress is 4000 psf.Test 2, The sample shears at a stress of 3500 psf when the normalstress is 6000 psf. Determine the following:a) Angle of Internal frictionb) Value of cohesionc) Compute the shear stress at a depth of 12 ft. if the unit weight ofthe soil is 150 pcf