Which of the following most nearly gives the distance of the neutral axis from the top of the beam? a. 212.51 mm c. 241.89 mm b. 233.09 mm d. 226.57 mm Which of the following most nearly gives the stress inn concrete? a. 11.83 MPa c. 13.16 MPa b. 12.19 MPa d. 12.48 MPa Which of the following most nearly gives the stress in the steel? a. 145.73 MPa c. 143.98 MPa b. 142.41 MPa d. 144.72 MPa

Which of the following most nearly gives the distance of the neutral axis from the top of the beam? a. 212.51 mm c. 241.89 mm b. 233.09 mm d. 226.57 mm Which of the following most nearly gives the stress inn concrete? a. 11.83 MPa c. 13.16 MPa b. 12.19 MPa d. 12.48 MPa Which of the following most nearly gives the stress in the steel? a. 145.73 MPa c. 143.98 MPa b. 142.41 MPa d. 144.72 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

-2.4m- 8 mm 200 mq 8 mm 250 mm 8mm The steel beam has the cross-sectional area shown. The beam is loaded as shown with the intensity of the distributed loading w=70 kN/m. Determine the absolute maximum bending stress in the beam in MPa.
11-85. If the concentrated force P = 2 kN is applied at the free end of the overhanging beam, determine the absolute maximum tensile and compressive stress developed in the beam. -130mm- 5 mm 200 mm 25 mm 25 mm
ka & pat 5em 2cm 4cm por Find steess the maximum chear and home Fined manent of inertia, T Find the normal stress/Volume and the Shear stress /volume as this volume is. directionally proportional to the mass of the beam. - Find in terms of P, and use MPA/mm³ for units.
Link AB is to be made of a steel for which the normal stress is 253 MPa. Determine the cross-sectional area (in mm2) for AB if P = 30.6 kNand d = 0.35. Round off the final aswer to four decimal places. 003 ехam.png ... 8 kN/m 35 OE D d d d
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress iss =10 MPa. 500 N/m 1.5 b OB - x m 2 m 2 m Calculate the centroid of the cross section of the beam O (1.5b, 1.5b] O (1.5b/2), (1.5b/2)] O (0.(1.5b/2)] O (0,0) [(1.5b/2), 0] O (0, 1.5b)
SE a iir Draw the V and M diagram of the beam. The cross section of the beam is a triangle with base 18 and height 12mm. Calculate the maximum shear stress in the beam. 5m 18mm D 1000N/m 12mm 2m B 1m 2m C A
PROBLEMS 237. The lower ends of the three bars in the figure are at the same level before the rigid homogeneous 18Mg block is attached. Each steel bar has an area of 600mm² and E=200GPa. For the bronze bar, the area is 900mm² and E-83GPa. Find the stress developed in each bar. BRONZE 1.6M STEEL 1M 18Mg STEEL 1M ТЕСНА
1. For the W 21x 62 steel beam below determine the actual value of om in the beam and the maximum value of the principal stress omax at the junction of the flange and the web. 20 kips 20 kips A B 10 ft 2 kips/ft 30 ft- C 10 ft D
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
10-7. The solid aluminum shaft has a diameter of 50 mm. Determine the absolute maximum shear stress in the shaft and sketch the shear-stress distribution along a radial line of the shaft where the shear stress is maximum. Set T₁ = 2000 N. m. E D 300 N-m 600 N-m T₁ Probs. 10-6/7 B 900 N-m
The rigid bar AD is supported by two steel wires of 1.5 mm diameter (E = 200 GPa) and a pinand bracket at D. Knowing that the wires were initially taut, determine the stress in each wirewhen a 1200 N load P is applied at D. What is the corresponding deflection of point D?
6-121 A wood beam is reinforced with steel straps at its top and bottom as shown. Determine the maximum bending stress developed in the wood and steel if the beam is sub- jected to a bending moment of M 5 kN m. Sketch the stress distribution acting over the cross section. Take E,, = 11 GPa, Est 200 GPa. 20 mm 300 mm -M = 5 kN-m 200 mm Prob. 6-121 20 mm