Assume a balanced 3-phase inverter output to a medium voltage transformer that will supply a balanced, 13,200 V delta-connected output of 26 A to the utility distribution system. If #2 Cu cable is used between the transformer secondary and the power lines, how far can the cable be run without exceeding a voltage drop of 2%?

Assume a balanced 3-phase inverter output to a medium voltage transformer that will supply a balanced, 13,200 V delta-connected output of 26 A to the utility distribution system. If #2 Cu cable is used between the transformer secondary and the power lines, how far can the cable be run without exceeding a voltage drop of 2%?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.58P: A single-phase two-winding transformer rated 90MVA,80/120kV is to be connected as an autotransformer...

See similar textbooks

Similar questions

How to generate 480V three phase 400Hz ac from 230V three phase 60Hz ac source? (Please specify the power components you pick, such as transformers, dc-dc converter, dc-ac converter and/or ac-dc converter, how these components are connected and the key parameters of these components, such as the turns ratio of transformer and the duty cycle functions for the converters.)
Question: In bridge type stepup cycloconverter during positive half cycle of supply voltage.'Ph' is positive with respect to 'N'. The circuit completes its path as Option 1: N- P2- load - P3 - Ph Option 2: Ph- P2- load - P3 N Option 3: N- P1- load - P2 Ph Option 4: Ph- P1- load- P2 N
Quiz2: We wish to connect a 6 KVA, 120/240 V transformer as an autotransformer to a 120 V source to supply 360 V toa load. ) Draw the circuit. b) What is the maximum load KVA that can be supplied? ©) Atthe maximum|oad, determine /Iy, and I, &) What are the possibilities to connect it as a stepdown autotransformer and determine the load voltage at each case?
With base MVA of 150 and base voltage of 33. If the reactance of the transformer is 0.23 pu. The parameter of the reactance of the transformer in the Neplan software is O 1.66 2.30 23 0.23 O Non of them
Thevalues of a phase measured from the no-load (no load) operation and short circuit test of a 220/48 V phase transformer are given in the table below. By applying nominal voltage to the high voltage (primary) winding, the lowvoltage (secondary) winding ends were left unloaded and the results of the no-load operation test were obtained. Byapplying nominal current to the low voltage windings, the high voltage windings were short-circuited, and the results of the short circuit test were obtained. In addition, 5 V direct voltage is applied to the high voltage winding, and the transformerdraws 2.2 A direct current . Calculate all equivalent circuit elements moved to the high voltage side.
There are 144 fuel cells are joined in a series through interconnects.there will be 4 stacks having 36 cell in each stack.these stacks are then oragnised in series and parallel combination to form a single module to deliver required voltage and output power.this SOFCs module then combined with CHP system to get thermal . From this data answer the following questions. a)Calculate voltage losses of module?.this question is very compulsory. b)Electrical efficiency of module? C)Thermal efficiency when module combine with CHP system? D)Combined electrical and thermal efficiency? The input parameters of single cell are given below: Ocv=1.020 Current density=2250mA/cm2 Power density=850mw/cm2 Cell active area= 121cm2 Net power=15kw System fuel utilization=80% Operating temp=550°c Cell voltage=0.8v Power of single cell=103 watt.
Q3-(A)- Three single-phase, 50 kVA, 2310/230 V, 60 Hz transformers are connected to form a 3-phase, star /delta, 4000/230V transformer bank. The equivalent resistance of e transformer referred to low-voltage is 0.012 and the equivalent reactance of each transformer referred to low-voltage is 0.016 W. The 3-phase transformer supplies a 3-phase, 120 kW, 230 V, 0.85 power-factor (lagging) load. (i) Draw a schematic diagram showing the transformer connection. (ii) Determine the winding currents of the transformer. (B)- Draw the graph of efficiency against load current when the transformer is loaded
A 100 KVA, 2000/200V 1-phase 2-winding Transformer is to be used as an auto transformer for stepping up the voltage from 2000 V to 2200 V. At rated load, the 2-winding Transformer has 2.5% loss, 3% voltage regulation & 4% impedance for an auto transformer determine (a) Voltage & current rating (b) KVA rating (c) Effiiency (d) Percentage impedance (c) Voltage regulation (f) Short circuit current on each side.
Quiz2: We wish to connect a 6 kVA, 120/240 V transformer as an autotransformer to a 120 V source to supply 360 V to a load. a) Draw the circuit. b) What is the maximum load kVA that can be supplied? c) At the maximum load, determine ln, fy, and I,- d) What are the possibilities to connect it as a step-down autotransformer and determine the load voltage at cach case?
A short-circuit test was performed on a 10kVA, 2000/400 V single phase transformer. The instruments indicated 100V, 5A and 100 W. Determine the secondary voltage when operating at rated load at 80% pf lagging at rated primary voltage. Provide values in order the space provided below: Re, Xe, I1, I2, and E1, E2
A A-A three transformer bank, each of 10 kVA supply a total load of 20 kVA. One of the transformer become, disable and hence the circuit works on V-V open delta connection. Find for this connection. (a) (b) (c) (d) (e) kVA load carried by each transformer. % of rated load carried by each transformer. Total kVA rating of V-V open A connection. Ratio of V-V and closed A ratings. % increase in load on each of the two V-V connected transformers. M
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False