a 60Hz, 250kVA, 2400/240V ideal transformer ,The primary-side current in A is:10Ozere1041.67-10-104.167-10Hone104.167

Given: An ideal transformer has f=60 HzS=250 kVAV1:V2=2400/240 V

Answered: a 60Hz, 250kVA, 2400/240V ideal…

Engineering

Electrical Engineering

a 60Hz, 250kVA, 2400/240V ideal transformer ,The primary-side current in A is: 10 zero 1041.67x10 104.167 - 10:5 HORE

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.5MCQ: For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is...

See similar textbooks

Related questions

Q: The quality factor of a bandpass filter that has an upper cutoff frequency of 121 krad/s and a lower…

A: Given, Upper cutoff frequency, ωH=121 kradsec Lower cutoff frequency, ωL=100 kradsec

Q: Nodal Analyvis

Q: Question # 1 a) A certain filter has the following transfer function. 1500 H(jw)= (jw+50)² Find the…

Q: What is cooling tube in transformer? Why does a transformer need cooling?

A: Cooling is the process of transferring heat from a transformer to the outside world. The…

Q: Calculate the voltage across resistance R3. R₁ ww 10V + 2V + ले । ww 3V R₂

A: Given data, Circuit diagram is given as,

Q: An RC High-pass filter consists of 5 nF capacitor and a 50 K resistor. The output voltage is taken…

A: Given, An RC high pass filter consists, Capacitance, C=5 nF Resistance, R=50 kΩ

Q: Some linear electrical system has an input voltage of V1(t)=25sin(90t) and

A: Given linear electrical system has an input voltage V1(t)=25sin(90t) steady-state output voltage…

Q: 1. What is the wavelength of light waves if their frequency is 5.0X1014 Hz? a. 0.60 m A b. 6.0 mm c.…

A: 1. Given, Frequency of light, f=5.0×1014 Hz

Q: (c) Figure Q2(c) is the shunt voltage regulator system. Characteristic of the system can be found by…

Q: (c) Find Ix in the circuit. 4 mA Ix 31x

A: Given circuit,

Q: A balanced Y-connected load absorbs in total 3 kW at a power factor of 0.6 lagging. If th line…

A: Given, A balanced Y-connected load absorbs, Total power, PL=3 kW Power factor, cosθ=0.6 lagging Line…

Q: QUESTION 3 Determine Vout. +30 V Vin OV -30 V Vout at Vin = +30V = Vout at Vin = -30V = www 2.2 ΚΩ…

A: assuming the diode is ideal, 1) If Vin=30V ,diode will be in reverse bias condition and hence it…

Q: 3. A coil consists of a Resistance of 980and an inductance of 180 mH. if an alternating voltage v-…

Q: P2.15: A line charge with charge density 2.00 nC/m exists at y = -2.00 m, x = 0.00. (a) A charge Q =…

Q: 4. a) Construct the Bode plot for the system having G(s)H(s)=- 80 s(s+2)(s+20) From the Bode plot…

A: Given

Q: 1000 KVA 11kV/415V RTR = 1.%, XTR -6.0% 200 KVAR 16 -C VLL = 11 kV, 50 Hz MVASc = 200 X/R = 2.4…

Q: A device has an output bit rate of 512 kbits/s. Design a digital modulation scheme for the device if…

A: According to the question, we need to design a digital modulation scheme for which Bit rate=512 k…

Q: Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal frequency is 600 Hz. R=2…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: The internal resistance of a primary cell is 412. It generates a current of 0.2A in an external…

Q: 2V. 1Ω Μ 12/0° V -1 Ω Figure Q2(b)(iii) + - -1 Ω 1Ω + V

Q: Analyze the given circuit and determine the minimum and maximum input voltage that the given Zener…

A: Diode is two terminal unidirectional device. Zener diode is special purpose diode in which current…

Q: In the circuit of Fig. P. 9.5.4 if the load is 2 kW, 230 V heater and V₂ = 230 V, 50 Hz. Calculate:…

Q: This is about two points, (x1,y1) and (x2,y2), on a straight line whose slope is given in dB/decade.…

Q: By referring to Figure with a suitable example, discuss what is meant by "greater complexity at the…

Q: Which one of the following d-c machine losses is determined by applying a standard value rather than…

A: There must be some losses in every useful piece of equipment. they cannot all operate at 100%…

Q: The parallel circuit in Example 13.1 is placed in series with a 2000 2 resistor. a) Express the…

Q: The antenna current of an AM transmitter

A: Given- For AM transmitter- Antenna current without modulation= 8A Antenna current when sinusoidal…

Q: 1. In the below circuit, find the current /through 1 Ohm resistor using Thevenin’s and Norton's…

A: Note: As per the policy we can solve only one question, please re-upload the remaining question as a…

Q: Find the AC values for the unloaded common-base amplifier. Draw the equivalent AC network. Use 25…

A: The ac circuit of the amplifier can be redrawn as The DC circuit of the amplifier will Now the…

Q: Nodes A to B has a voltage drop of 5.0 cos (2t + /3. Nodes A and D is connected by 0.2 F capacitor.…

Q: 19. Which of the following is a universally adopted shape of cell?

A: The correct option along with the explanation is provided in the following section.

Q: DESIGN A SEQUENTIAL DETECTOR THAT DETECTS THE CODE 1010

A: A sequential state machine is a sequence detector. The output of a Mealy machine is dependent on…

Q: Given the signal v(t) = u(t)- u(t-1) a) Sketch v(t). b) Find the normalized energy and power (in…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: A single phase transformer is required to be designed to give an output of 4 A at 24 V, from 230 V,…

Q: Using nodal analysis, find V, in the circuit. 2 ΚΩ 4 ΚΩ ν(+ 2 ΚΩΣ | 2 ΚΩ Vo

A: Given circuit,

Q: What will be the resultant capacitance of the given combination? =1mF=2mF=3mF=4mF= 5 mF

A: Capacitance:- It stores the energy in the form of an electric charge. Farad is the SI unit of the…

Q: x(t) = 10cos (2π × 10°t + 3 cos (2π × 100t)) ) Determine fi(t), the instantaneous frequency of the…

Q: Calculate the maximum efficiency, n for the class B push-pull amplifier shown in Figure Q4(b).…

A: According to the question, for the given class B amplifier as shown below We need to discuss (1)…

Q: Calculate the voltage across resistance R3. R₁ ww 10V + 2V www R. + ले । 3V R₂

A: Given circuit,

Q: Find the voltage across A and B in the circuit shown in figure 5V= 69 www 40 www. RK 12 V 12V 40 www…

Q: (b) Based on the combined circuit (series and parallel) as shown in FIGURE Q1(b), answer the…

A: Given here a electrical circuit and asked to find the total resistance and total current and I1 , I2…

Q: A Moving to the next question prevents changes to this answer. Question 15 Design a 5-tap FIR HPF…

Q: The voltage VAN in the single-phase equivalent circuit for a balanced three-phase circuit (positive…

A: Given, For the single phase equivalent circuit of a balanced three-phase +ve sequence circuit, The…

Q: A negative feedback amplifier is shown in Figure 1. If the gain, A, of this amplifier without…

A: Given, Gain without feedback A=5000

Q: By referring to Figure 2, given that D = (20p³/4)a,(C/m²) in cylindrical coordinates, use right side…

Q: The line-to-neutral excitation voltage

Q: 8. Determine the reluctance of a materi- al with a length of 0.28 m and a cross- sectional area of…

A: Given: A material has Length, L=0.28 m Cross sectional area, A=0.08 m2 Absolute permeability,…

Q: 2) Determine the value of R for the circuit below that will result in a diode current of 10mA if…

A: Given, The circuit is, Diode current, ID=10 mA Supply, E=7 V

Q: difference betwwen substation and transmission.

A: A high-voltage electric system facility is known as a substation. It is used to switch equipment,…

Q: Solve completely the given circuit below by applying two ac theorems discussed. Choose among…

A: It is given that: Z1=4-j8 ΩZ2=9-j12 ΩZ3=8-j10 ΩZ4=6+j12 ΩV2=30∠-60° V

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

a 60Hz, 250kVA, 2400/240V ideal transformer ,The primary-side current in A is:
10
Ozere
1041.67-10-
104.167-10
Hone
104.167

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
A 100 Kva transformer has 400 turns on the primary and 80 turns on the secondary. The primary and secondary resistances are 0.3 ohm and 0.01 ohm respectively , and the corresponding leakage reactances are 1.1 ohms and 0.035 ohm respectively. The supply voltage is 2200 V. The % VR and the secondary terminal voltage for full load 0.8 pf leading are: -1.44 and 330.29 V O 1.54 and 4467.7 V -1.54 and 446.77 V
n 7 In step up transformer, secondary turns are less than primary turns. out of Select one: O True uestion O False VION MS team link Jump to... search Chp
Given Zo-j407 2, R₁143, R6317 52 and a 0.04, what is the magnitude of the source voltage Vs (in V rms) in the primary of the ideal transformer? Vs R₁ ww Answer: Zc Zc R₁ Use up to 2 digits after the decimal point if necessary in your answer below VL-28020 V TR
Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 Vrms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Use germanium diodes. 110 Vrms 00000 lllll Rsurge www 10 Ω C 100 μF ww RL 3.3 ΚΩ
A Volt ac voltage is applied to the primary input of a transformer. A load of B ohms at the output it depends. Since the primary spiral number of the transformer is C and the secondary spiral number is C, the primary current is, Find the secondary voltage and secondary current. A= 752 B=257 C=257 Ç= 16
For the following circuit if the secondary voltage of the transformer is 20V rms, the PIV of the diodes are ZV +1H +1 C3 D₂ D₁ 000 000000000 + C₁ O 55 V O 61.61 V 33 V O56.56 V C₂ HE 2V + m D3 + Ca H 2V
The full-load copper loss of a transformer is 1600 W. At half-load, the copper loss will be O a. 1600 W b. 6400 W O c. 400 W d. 800 W 4 11
The efficiency of a transformer at load 0.8 p.f. Lag is -- at load 0.8 p.f. Lead * equal less than more than none of these
The open-circuit voltage of 242 V and the full load secondary voltage of 234 V, then the % regulation of a transformer is
The primary of a current transformer takes 1 A at a power factor of 0.4 when it is connected across a 200-V, 50Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. What is now the value of primary current?