An overhang hollow shaft having inside diameter 0.5 time outside diameter, carries a cast iron pulley having 800N weights and 900mm diameter, at 250mm from the nearest bearing. The pulley is driven by another pulley mounted on the shaft placed bellow it, to transmit 35kW at 400r.p.m. The belt ends are vertical and parallel; if the ratio of tensions in belt is 3 and the permissible shear stress for material of shaft is limited to 200MPa, determine the diameters of shaft.

An overhang hollow shaft having inside diameter 0.5 time outside diameter, carries a cast iron pulley having 800N weights and 900mm diameter, at 250mm from the nearest bearing. The pulley is driven by another pulley mounted on the shaft placed bellow it, to transmit 35kW at 400r.p.m. The belt ends are vertical and parallel; if the ratio of tensions in belt is 3 and the permissible shear stress for material of shaft is limited to 200MPa, determine the diameters of shaft.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

An overhang hollow shaft having inside diameter 0.5 time outside diameter, carries a cast iron pulley having 800N weights and 900mm diameter, at 250mm from the nearest bearing. The pulley is driven by another pulley mounted on the shaft placed bellow it, to transmit 35kW at 400r.p.m. The belt ends are vertical and parallel; if the ratio of tensions in belt is 3 and the permissible shear stress for material of shaft is limited to 200MPA, determine the diameters of shaft. 1 Add file
Two 400 mm diameter pulley are keyed to a simply supported shaft 500mm apart. Each pulley is 100mm from its support and has horizontal belts tension ratio being 2.5.if the shear stress is to limited to 80MPa while transmitting 45kW at 900 r. p. m. Find the shaft diameter if it is to be used for the input - output belts being on the same or opposite sides
The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted. Q2 Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be takenas 1.5. Q3 a) An universal coupling is used to connect two mild steel shafts transmitting a torque of 6000 N- m. Assuming that the shafts are subjected to torsion only, find the diameter of the shaft and the pin. The allowableshear stresses for the shaft and pin may be taken as 55 MPa and 30 MPa respectively.
thick lnange be! The total torque required to turn the double threaded power screw is 55 N.m. If the screw turns at 285 rpm and the pitch of 4mm, find: A. The horsepower input of the power screw. B. The efficiency if the weight loaded is 10 kN.
A pipe with an outside diameter of 4.0 in. and an inside diameter of 3.624 in, is subjected to an axial force of P-850 lb, a horizontal force of Pz 1560 lb, and a concentrated torque of T-2940 lb-in, acting in the directions shown. Assume a 49 in. Section propertles for the pipe are A-2.2514 in.?,J-8.199 in.", and ly 1-4.0995 in.. Determine the normal and shear stresses at point K, and show these stresses on a stress element Answer: Oy = psi Txy psi
A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft, providing four pairs of contact surfaces. The outside diameter of the contact surfaces is 240 mm and inside diameter 120 mm. Assuming uniform pressure and coeff. Of friction is 0.3. Find the total spring load pressing the plates together to transmit 23kw power at 1475 revolution per minute. If there 6 springs each of stiffness 13 kN/m and each of the contact surfaces has worn away by 1.25 mm. find the maximum power that can be transmitted assuming uniform wear. A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft, providing four pairs of contact surfaces. The outside diameter of the contact surfaces is 240 mm and inside diameter 120 mm. Assuming uniform pressure and coeff. Of friction is 0.3. Find the total spring load pressing the plates together to transmit 23kw power at 1475 revolution per minute. If there 6 springs each of stiffness 13 kN/m and each of the contact surfaces…
A flange coupling is to connect two 57mm shafts. The hubs of the coupling are each 111m indiameter and 92mm hub length. Six 16- mm bolts in a 165-mm diameter bolt circle connects theflanges. The key is 14mm high, 14mm wide and 86mm long. Coupling is to transmit 45kW at 160 rpm.For all parts, yield point value in shear is one-half the yield point value in tension or compression thatis 448MPa. Determinea. Shearing stress of the key and its factor of safetyb. Bearing stress of the key and its factor of safetyc. Shearing stress in bolts and the factor of safety based on yield point
5. An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 m apart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coeffi- cient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be trans- mitted. [Ans. 2.39 kW]
Please solve step by step both sub parts. shaft transmits 75 kW power at 300 r.p.m. The distance between the two bearing is 3000 mm. It is subjected to torsion only. Calculate the diameter of the shaft, (1)For steady loading and (ii) For suddenly applied load with minor shocks. Take the allowable shear stress for the shaft material as 35 N/mm².
Q/A shaft supported at the ends in ball bearings carries a straight tooth spur gear at its mid span and is to transmit 7.5 kW at 300 r.p.m. The pitch circle diameter of the gear is 150 mm. The distances between the centre line of bearings and gear are 100 mm each. If the shaft is made of steel and the allowable shear stress is 45 MPa, determine the diameter of the shaft. Show in a sketch how the gear will be mounted on the shaft; also indicate the ends where the bearings will be mounted? The pressure angle of the gear may be taken as 20°.
Two equal gear wheel of 360 mm p.c.d and 6 module are in mesh if the pressure angle 20 determine the maximum addendum necessary if there are always to be at least two pairs of teeth in contact . if the gear wheels rorates at 110 r.p.m and 6 kw is being transmetted find the normal force between the teeth assuming that the total force is dividing equally between the two pairs of teeth Neglect the frection. (Ans 6.8mm , 1.54KN .)
An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 mapart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted