Q2 Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be takenas 1.5.

Q2 Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be takenas 1.5.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.8P: Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the...

See similar textbooks

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 mapart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted
Two 400 mm diameter pulley are keyed to a simply supported shaft 500mm apart. Each pulley is 100mm from its support and has horizontal belts tension ratio being 2.5.if the shear stress is to limited to 80MPa while transmitting 45kW at 900 r. p. m. Find the shaft diameter if it is to be used for the input - output belts being on the same or opposite sides
A cast Aluminum crlinder o f a Portable hodrawlic 208 Mm in diameter The 16,8 N/mm2 by gauge riveter is Pressure. of The fluid is Determine Sui table thicknesS of the inder wall assuming that the Yield Point stress 442 N/mm2 And factor of safety of 6.2 Calculate. the tangential and radial streses middle radius and at the inner outer surface.
A workshop crane is lifting a load of 28 kN through a wire rope and a hook. The weight of the hook etc is 15 kN. The rope drum diameter may be taken as 30 times the diameter of the rope. The load is to be lifted with an acceleration of 1.2 m/sec2. Take a factor of safety of 6 and Young's modulus for the wire rope is 80 kN/mm2. The ultimate stress may be taken as 1800 MPa. The cross-sectional area of the rope may be taken as 0.38 times the square of the wire rope diameter. Neglect the effect of impact load. Calculate the diameter of the wire rope.
A 75mm shaft is subjected to 5KN-m torque. Find the stress developed in MPa. Meanwhile, determine the maximum mean diameter of a taper for use to fix a lever to a shaft. If it transmit a maximum torque f 750 in-lb . The shaft diameter is in 3in
Find the tension of the cord that extends from point C to D and compute for stress experienced by the catble if it's diameter in 1.51 in? Neglect the members weight and friction Round-off your answer into the nearest whole number 150 Ib/ft 6 ft 8 ft 6 fh -12 ft
A keyed gears delivers a torque of 912.4 N-m thru its shaft of 63.5 mm outside diameter. If the key has thickness of 15.875 mm and width of 11.1125 mm, find the length of the key. Assume permissible stress value of 61.2 MPa for shear and tension at 99.8 MPa
. The mean diameter of the driving pulley for a vec-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of frietion between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm.
A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. It is press fit on a solid shaft of same material with diameter 42mm such that the nominal diameter between sleeve and shaft became 41mm. a. Find the pressure developed between shaft and sleeve. b. Draw the tangential, radial, and total stress as a function of radius, for both sleeve and shaft. c. Find the maximum shaft diameter that can be used before failure.
5. An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 m apart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coeffi- cient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be trans- mitted. [Ans. 2.39 kW]