An A36 angle with staggered fasters in each leg is in the figure below. The standard hole diameter is 23mm. The gross area of the angle is 4387.088mm^2. 1. Which of the following nearly gives the smallest effective net area (mm^2) for the tension member. a. 2632 c. 3561 b. 3752 d. 3311 2. What is design strength of the tension member in kN. a. 979 c. 653 d. 662 b. 993 3. What is the allowable strength of the member in KN a. 979 b. 993 c. 653 d. 662 Holes Top View OO 000 50 40 40 40 40

An A36 angle with staggered fasters in each leg is in the figure below. The standard hole diameter is 23mm. The gross area of the angle is 4387.088mm^2. 1. Which of the following nearly gives the smallest effective net area (mm^2) for the tension member. a. 2632 c. 3561 b. 3752 d. 3311 2. What is design strength of the tension member in kN. a. 979 c. 653 d. 662 b. 993 3. What is the allowable strength of the member in KN a. 979 b. 993 c. 653 d. 662 Holes Top View OO 000 50 40 40 40 40

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A staggered riveted connection has rivets arranged as shown below. The plate is 400 mm and 12 mm thick with four bolt holes. The diameter of rivet is 34 mm The diameter of the rivet hole is assumed to be 5 mm larger than rivet diameter. Fy = 248 MPa. Fu= 410 MPa, Fv in rivets is 372 MPa. 1. Which of the following gives the distance b so that the net area in section 1 – 2 – 3 – 4 equal to the net area in section 1 – 2 – 4 a. 30.01 mm b. 25.12 mm c. 19.7 mm d. 12.23 mm 2. Which of the following gives the net area using the computed value of b. a. 4622.65 mm² b. 5623.75 mm² c. 3623.64 mm² d. 7652.85 mm² 3. Which of the following gives the maximum tensile force that the connection could carry if the allowable yield stress is Fy/1.67. a. 432.12 kN b. 724.73 kN c. 253.25 kN d. 712.81 kN 4. Which of the following gives the maximum tensile force that the…
Instructions:-Write down each step clearly in calculation suggestion what you are doing.( you need to tell why you selected particular value ofø (phi) and U). What and why you are calculating certain step Consider R= 433.5 PROBLEM A welded tension member is consisting of two channels placed 400mm back to back with flanges turned out. Select a channel for factored tensile of 4RKN using A36 steel and AISC specifications.The member is to be 15m long. PLASE USE THE EXAMPLE AS GUIDE OF ALL STEPS AND FORMULAS TO BE USE
Determine the elongation of the steel bar shown. B A 1. ds L P-416 KN L-875mm E-200 GPa dA= 250mm d 600mm Answer in trin and in 5 decimal places (e, O.20205mm)
43 OSFu A tension member with an allowable tensile stress of 0.6Fy is connected to the gusset plate using four rivets having a diameter of 34mm. Assume the diameter of the hole is 2mm more than the rivet diameter. It is required to determine the value of b so that the net width along rivets 1-2-3-4 is equal to the net width along 1-2-4. > Determine the value of b > Determine the most critical net area The value of T without exceeding the allowable stress. Gusset plate If failure will occur in djagonal s 2 direction add a value 4g C0mm b. 6. 100mm 400mm 100mm 100mm 12mm 150mm
5. what is the shear rupture capacity of the shear plate of the shear connection in kips? (2 decimal places)A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
4.) A thin plate PQR is deformed so that the corner Q is displaced downward 1.0 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges. 5) A pin mado of steo1 ie insorted in o short hanging TAOodon mombor ond iG 1used to Supnort lond E - 20
EN O Aロa。 USEFUL LINKS v M Time Select the reinforcing needed for the short tied column shown for the following: Pn=2000 kN, 250 mm, e 200 mm. f28 MPa, fy= 420 MPa: (Add attachments below) 70 s00 mm 640mm 70 mm 70 mm 70 mm 210 mm 350 mm
2. A staggered riveted connection has rivets arranged as shown. Diameter of rivet is 28 mm. Use AISCINSCP Specs. Fy 248 MPa, Fu = 400 MPa. Determine the distance "S" so that the area area in chain ABCD is equal to the net area in chain ABD. Determine also the tensile capacity of P. 45 10 350 mm 90 90 I mm 60 mm 888
Problem 8: Determine the location ỹ of the centroidal axis i – i of the beam's cross-sectional area. Neglect the size of the corner welds at A and B for the calculation. -150 mm 15 mm B 150 mm -15 mm 50 mm
Part A: Two bolts secure a plate to a girder as shown in Figure a below. A 3kN vertical load is applied. a) Replace the applied load at C with a force-couple at D. (b) Assuming the bolts carry equal amounts of shear and applied moment, calculate the resultant bolt load due to the applied force-couple. Draw a FBD of the bolt group with the applied force-couple and bolt reacts. 350mm A 300mm 3kN
e. Calculate "P" in KN considering failure on bearing on block shear Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
WHERE: BOLT DIAMETER = 22mm Fy = 241Mpa Fu = 414Mpa