A wye-connected, 3-phase system has the following sequence components of current Zero sequence current = 12.5430° Positive sequence current = 284-45° %3D Negative sequence current = 202-32° Determine the current flowing in the neutral wire

A wye-connected, 3-phase system has the following sequence components of current Zero sequence current = 12.5430° Positive sequence current = 284-45° %3D Negative sequence current = 202-32° Determine the current flowing in the neutral wire

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.5P: A 60Hz, single-phase source with V=27730 volts is applied to a circuit element. (a) Determine the...

See similar textbooks

Related questions

Q: Find the current in a ground loop that is 250 m long, has a wire resistance of 0.04 ohms/m, and has…

Q: Find the current and voltage using superposition across the 4- kN resistor(I, and Vx, respectively).…

A: In this question, We need to determine the current Ix and voltage Vx using the super position…

Q: c) The waveform shown in Figure 1c is passed into an Ideal Low Pass Filter (ILPF) which has a…

Q: 6) A sequential circuit has two JK flip-flops A and B and one input x. The circuit is described by…

A: Consider two JK flip-flops A and B and one input x. flip-flop input equation are JA=x, KA =B,…

Q: For the network below, determine: a. Id b. Vds c. Vd d. Vs 20 V 2.2 kn oss -45 ma 0.68 ka

A: The solution is given below

Q: 11.) A single phase inductive load at 0.70 power factor lagging takes 32 kVA power. Compute the…

A: The solution is given below

Q: An. A/D converter uses 14-bit numbers linear sign magnitude PCM and has a voltage range of -6V to…

A: The solution is given below

Q: alternator is rated at 15kVA, 460V. The armature resistance and reactance are 1.50 and 30…

A: In this question we will find single phase alternator no load voltage with given data...

Q: For the electrical circuit system shown, find the transfer function Io(s)/V(s)and Vo(s)/Io(s

A: In this question, We need to determine the find the transfer function Io(s)/V(s)and Vo(s)/Io(s).

Q: (b) Let x(t) be a real-valued signal with X (w) = 0 when |w| > 990n. Amplitude modulation is…

A: Brief description: Low pass filter is used to pass the frequencies which are within the higher cut…

Q: Problem B G4 G2 G3 R C H H2

Q: 3After being closrd for a long fime, the sioitch in the circutt s pened ot t =O Tind kCt) for t70.…

Q: (c) Find the frequency response (magnitude and phase response) of a system at an angular frequency…

Q: AGILA satellite is located 36000 km above the earth’s surface. Assuming free space condition, what…

A: To find the path loss in dB of the signal if the operating frequency is 3 GHz . And distance between…

Q: 8.) If the range selector knob is set to 50 ACV, what would be the voltage reading of the yellow…

A: Here we understand about the measurement process for given multimeter/multitester.

Q: If the range selector knob is set to 50 ACV, what would be the voltage reading of the yellow needle?

A: Given the full scale deflection of the analog multimeter is 10 V AC and there is a multiplier of 5…

Q: A current balance bridge shown in Fig. 2 has resistance of R1 = R2 = 1kQ, R4 = 5902, R5 = 102, and V…

A: To find the value of R3 if a current of 0.5 mA is required to Balance the bridge .

Q: 12 V 2.2 ka 220 k. B= 60 ,=40kQ

A: We need to find out voltage gain for given circuit

Q: You are given a report that shows 2 different designs of a quadruple stage impulse generator…

A: Design "A" is more suitable for creating impulsive voltage waveforms than Design "B."

Q: 14.Describe the construction of 1ph IM.

A: Note: We are authorized to answer the first question since the exact one wasn’t specified. Please…

Q: Four resistors, R1 = 1000, R2 = 2500, R3 = 3500 and R4 = 2002 are connected such that the parallel…

Q: . The steady state speed of a 60 Hz induction motor is 1150 rpm. Compute the number of poles of the…

Q: Question 2 For how long a voltage drop could be measured across R1 during a discharging process? С1…

Q: 2.)For the p-type semiconductor doped with Na = 101°cm-3 at T = 300K, no light was applied before t…

Q: The balanced system below has a phase voltage of 120 V. It supplies a balanced load Z1 that has…

A: In this question we need to find a total reactive power and true power of the given three phase…

Q: 24.) The figure below shows a series-parallel circuit. Compute for the total active power consumed…

A: This question is related to power calculations

Q: 2) The amplitude of the emf in the below circuit is 150V, while the angular frequency is 60x. The…

Q: Binary codes. Convert from Gray code to binary X1 = 10101111. From the result obtained, apply a…

A: The solution is given below

Q: For the voltage-divider bias configuration. Determine the level of output impedance or Zo with the…

Q: 2) The amplitude of the emf in the below circuit is 150V, while the angular frequency is 60x. The…

Q: O Calculate the photon energy of violet, blue, green, orange and red lights.

Q: Five inductors, each 10 mH, are connected in series across a sine wave ac source. Determine the…

A: Given data, Five inductors each of 10 mH are connected in series.

Q: how sommerfield model overcomes the limitations of Drude and Lorentz, drude model

A: Both the theories i.e Somerfield theory and Drude and Lorentz model are based on the atom and its…

Q: Find the z-transform of n an un.

Q: 3. Solve the inverse Laplace transform of the following. Simplify your answer H(s): 3 + s2+4 s2+12…

A: In this question we have to find the inverse laplace

Q: need the answer quickly

A: This extractor hood is nothing but the valve present in the system to release pressure generally the…

Q: Draw the equivalent circuit if you are going to perform Short Circuit Test(SCT)(at terminals a-b,…

Q: Bet Bershat low -> 16 15() Ri 30 Rež

Q: A power transformer with a voltage rating of 12500:240 V has a primary current rating of 50 A. Find…

A: given that, primary voltage VP = 12500 v secondary voltage Vs = 240…

Q: 4.) A load of 23 kVA, with .65 power factor lagging is connected to a 240 volts line. How much…

Q: R, I, V2 60V V, Figure 8-2. CALCULATED POWER POWER SUPPLIED VALUES DISSIPATED (1, x En) V, = V %D R1…

Q: Solve for flux density (in gauss) from a magnetic flux of 5,000 Mx through a perpendicular area of…

Q: PREFINALS TASK 2 Give the truth table of the ff. Boolean expressions: 1.) F=(A'CB+ AB)' 2.) F = (DA'…

A: The solution is given below

Q: Example: Find the v(t) and i(t) in the circuit in Figure 9.16 v = 10 cos 4t 0.1 F =v Figure 9.16

Q: A balance Y-connected load of (3 + j8 ) ohms per phase is supplied by a balanced three- phase, 60…

A: In this question, We need to determine the voltage VAB , VCA and current IA as per our…

Q: Ideal Non-inverting Operational Amplifier 1- Introduction Cguivalont Circuit

A: Ideal Non-Inverting Amplifier:

Q: Find the v(t) and i(i) in the circuit in Figure 9.17 4Ω ww v = 20 sin(10t + 30°) V 0.2 H Figure 9.17…

Q: Use superposition theorem, find i, in the following circuit. ix 10 cos(2t + 10°) A(1 2H 20 cos(2t…

Q: Problem 4 A Y-connected three-phase, 415V, 1460 rev/min, 50 Hz, 4-pole induction motor has the…

A: The efficiency of a motor: It is determined the dividing the mechanical output power by the…

Q: 2. y" — Зу" — 4y' + 12у 3D 12e t; у (0) %3D 4, - y'(0) = 2, y"(0) = 18

A: Formula for unilateral Laplace transform is given below:

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

A wye-connected, 3-phase system has the following sequence components of current:
Zero sequence current = 12.5430°
Positive sequence current = 284-45°
%3D
Negative sequence current = 202-32°
Determine the current flowing in the neutral wire

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit.
The figure shows a 3-phase bala Time left 1:06:30 200 /00 Vrms. sequence electrical system. Vcn Vbn %3D al Balanced (-) sequence 100 so a 2000 Vms Select one: O a. 200 /-120 Vrms O b. 200 v2 /0 Vrms O C. 200 /0 Vrms O d. 200 v2/-120 Vrms e. 200/120 Vrms
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.
A three-phase circuit is balanced. The source voltage for the a-phase has a magnitude of 100 volts, and you can assume the phase angle is a reference of 0 degrees. Write the phasor expressions with proper subscript notation for the source voltage for each leg of the three-phase source if it is in a positive phase sequence.
what are the advantages and Disadvantages Connecting transformers 3 Phase between (delta to Star)
Can you explain the given questions in an original way? Single Phase and Three Phase Principles • Single Phase Generators • Two Phase Generators
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3- phase side. The main transformer primary to secondary turns ratio is (12/1).
In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the line-to-neutral voltages are always equal to zero. (a) False (b) True
Three single-phase transformers, each rated 10MVA,66.4/12.5kV,60Hz, with an equivalent series reactance of 0.1 per unit divided equally between primary and secondary, are connected in a three-phase bank. The high-voltage windings are V-connected and their terminals are directly connected to a 115-kV three-phase bus. The secondary terminals are all shorted together. Find the currents entering the high-voltage terminals and leaving the low-voltage terminals if the low-voltage windings are (a) Y-connected and (b) - connected.
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)