A W12 x 65 is used as a simply supported, uniformly loaded beam with a span length of 50 feet and continuous lateral support. The yield stress, F, is 50 ksi. If the ratio of live load to dead load is 3, compute the available strength and determine the maximum total service load, in kips/ft, that can be supported. y a. Use LRFD. ina b. Use ASD.

A W12 x 65 is used as a simply supported, uniformly loaded beam with a span length of 50 feet and continuous lateral support. The yield stress, F, is 50 ksi. If the ratio of live load to dead load is 3, compute the available strength and determine the maximum total service load, in kips/ft, that can be supported. y a. Use LRFD. ina b. Use ASD.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.1P

See similar textbooks

Similar questions

If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
A W12 X 65 is used as a simply supported, uniformly loaded beam with a span length of 50 feet and continuous lateral support. The yield stress, F, is 50 ksi. If the ratio of live load to dead load is 3, compute the available strength and determine the maximum total service load, in kips/ft, that can be supported. a. Use LRFD. b. Use ASD.
A simply supported beam is subjected to a uniform service dead load of 15kN/m(including the weight of the beam), a uniform service live load of 30kN/m. the beam is 12 meters long and is laterally supported at the midspan, and A572 Gr.50 steel is used. Is W30x108 adequate? Assume Cb=1 by 4 d fore k h h Z S Ly 267 TH mm 19.3 757 13.8 min m 35.8 685.4 54.6 737.7 5670 x10^3 4900 x103 mm 60.8 x10 6 mm 2080 x10 3 8300 x10^9 mm www
The beam shown in Figure is a W36 x182. It is laterally supported at A and B. The 300 kip load is a service live load. Using the unfactored service loads, a. Compute Cb. Do not include the beam weight in the loading. b. Compute Cb. Include the beam weight in the loading.
The beam shown in Figure is a two-span beam with a pin (hinge) in the center of the left span,making the beam statically determinate. There is continuous lateral support. The concentratedloads are service live loads. Determine whether a W12 × 79 of A992 steel is adequate.a. Use LRFD.b. Use ASD.
Use 2015 NSCP The beam shown is a W10x77 and has continuous lateral support. The load P is a service live load. If Fy = 36ksi, what is the maximum permissible value of P. a) Use LRFD b) use ASD P 15'- 15'-
A simply supported beam subjected to a uniform service Dead load of 20kn/m (including the weight of the beam), a uniform service live load of 35kn/m. The beam is 12m long and is laterally supported at midspan, and A572 Gr. 50 steel is used. Assuming cb =1. Verify if w30x108 is adequate? Use fy=344 mpa
PROBLEM 4: The beam shown the figure below is a W16x31 of A992 steel and has continuous lat- eral support. The two concentrated loads are service live loads. Neglect the weight of the beam and determine whether the beam is adequate. a. Use LRFD. b. Use ASD. 60k 60k W16 x 31 asap +4
The beam under the Live and Dead loads is shown below. The steel class is $235. Lig L1 L2 a.) Evaluate the slenderness of the web and flange. b.) Calculate the Cb value based on the loads. c.) Calculate the bending moment capacity of the beam... d.) Is the beam cross-section enough for the given loads. L3
The beam shown is simply supported and has lateral support only at its ends. The only service dead load is the weight of the beam. Determine whether it is satisfactory for the load shown. A992 steel (E= 345 MPa and F= 450 MPa) is used, and the 30 KN/m is a service live load. Use LRFD 30 KN/m WiL = 30 KN/m W16x 40 -Centroid W16 x 40 3m
The cantilever beam shown in Figure P5.8-4 is a W10 × 77 of A992 steel. There isno lateral support other than at the fixed end. Use an unbraced length equal to the spanlength and determine whether the beam is adequate. The uniform load is a servicedead load that includes the beam weight, and the concentrated load is a service liveload.a. Use LRFD.b. Use ASD.