A thin-walled tube having a semi circular shape has an outside diameter of 50 mm and a wall thickness of 2mm. If the stress concentration at the corners is neglected,What torque will cause a shearing stress of 40 MPa in N-m?
Q: A shaft is to be fitted with a flanged coupling having 8 bolts on a circle of diameter 150mm. the…
A: Stress: When a component or a part is subjected to any external force, a resisting force will be…
Q: A hollow circular torsion member has an outside diameter of 22 mm and inside diameter of 18 mm, with…
A: GivenDo=22mmDi=18mmD=20mmτ=70MPa at mean diameterG=77.5GPa
Q: A shaft is to be fitted with a flanged coupling having 8 bolts on a circle of diameter 150 mm. The…
A:
Q: diameter solid steel cylinder in which a 7 mm diameter hole has been drilled from end B up to point…
A:
Q: lid bar consisting of two segments AB and BC, as shown in Figure 2(a), is fixed at C. Segment AB has…
A:
Q: A steel tube with outer and inner diameters are 86mm and 52mm respectively is twisted by torques at…
A:
Q: A flanged bolt coupling is used to connect a solid shaft 94 mm in diameter to a hollow shaft 100 mm…
A:
Q: Referring to Figure Qla, assuming a hollow cylindrical block at the mid-section of the femur with an…
A:
Q: 11 A rectangular bar section of aluminium alloy has outside dimensions 100 mm x 50 mm, as shown in…
A: As illustrated in the image, a rectangular bar section of aluminium alloy has outer dimensions of…
Q: A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20 mm…
A: Find the length of key .
Q: PROBLEM 3. A 5-m steel shaft rotating at 1.20 Hz has 72 kW applied at a gear that is 2 m from the…
A: When an object rotate about the point due to the linear force act on the object is known as the…
Q: 03: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C).…
A: The given question belongs to the topic Torsion of circular shafts. In this question, rotation given…
Q: A shaft ABCD 70 mm in diameter is subjected to torques of 1500 N-m at B and 1100 N-m at C acting in…
A:
Q: A hollow steel shaft with an outside diameter of 80 mm and a wall thickness of 11 mm is subjected to…
A:
Q: The constant wall thickness of a tube with the elliptical cross section shown is 0.12 in. what…
A: As per given Question Wall thickness =0.12in Shear force =6000 psi We have to determine the torque
Q: A flanged bolt coupling consists of six 10-mm diameter steel bolts on a bolt circle 300 mm in…
A:
Q: A steel tube of outer diameter 86mm and inner diameter 52mm is under pure torsion. The diameter of a…
A: Outer diameter = 86 mm Inner diameter = 52 mm Answer is (B) 81.98 mm
Q: A hollow tubular component is made of Steel having a Young's modulus of 205 GPa and yield strength…
A: Given Data⇒ Tensile load (F)=38 KN External diameter of the hollow tubular component is d2=45 mm…
Q: Problem 4 A 200-mm-diameter pulley is prevented from rotating relative to 60-mm-diameter shaft by a…
A:
Q: A hollow shaft and a solid shaft constructed of the same material have the same length and the same…
A: In the given problem, radius of solid shaft and outer radius of hollow shaft is same i.e., R The…
Q: Determine the allowable value of the torque, T, which can be applied to the solid circular shaft…
A:
Q: pplied torque of 1.5 Nm is found to produce an angular twist of 0.4°, measured on a length of 0.2 m…
A: Given data,hollow shaftD=50mm=0.05m so, R=0.025d=30mm=0.03mTa=1.5 Nmθ=0.4°⇒0.4×π180=0.006981…
Q: An aluminium hollow thin-wall torsion member shown in Fig. 3.15 is 3 m long. If a torque of 10 kN-m…
A: We know that a 3 m long aluminium hollow thin wall torison member is illustrated in the diagram.We…
Q: A torque of 2.5 kN.m is applied to the hollow, thin- walled, aluminium section shown in Fig. 3.18.…
A: As illustrated in the picture in the question, a torque of 2.5 kN.m is given to the hollow,…
Q: A 100 mm diameter, 10 m long shaft is used to transmit power at 150 rpm. If angle of twist produced…
A:
Q: Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm…
A: Given data T=92.7 N-mD=20 mmt=2 mmd=16 mm
Q: A hollow steel shaft is transmitting 15 kW at 420 rpm. Calculate the thickness of the shaft where…
A: Given, Power, P=15 kW Speed, N=420 rpm The outside diameter of the shaft, Do=50 mm Allowable shear…
Q: A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further…
A: Given, Diameter of shaft = d = 100 mm Axial stress = σx = 50 MPa = 50 N/mm2 Torque = T = 10 kNm = 10…
Q: A composite shaft is made of slipping a bronze tube of 3-in. outer diameter and 2-in. inner diameter…
A: Calculate the polar moment of inertia of the solid steel shaft-Jst=π32D4Where-D=diameter of steelD=2…
Q: An external pressure of 10 MPa is applied to a closed-end thick cylinder of internal diameter 160 mm…
A: External pressure P= 10 Mpa Di = 160 mm ;r = 80 mm Do = 320 mm ; R =160 mm σcmax = 30 Mpa E = 207…
Q: Maximum shear stress developed on the surface of a solid circular shaft under pure torsion is 235…
A:
Q: A composite shaft is made of slipping a bronze tube of 3-in. outer diameter and 2-in. inner diameter…
A:
Q: A flanged coupling rotating at 400 rpm have 4 steel bolts evenly tightened around a 100 mm bolt…
A:
Q: The hollow rod shown below is 2.99 meters long and is subjected to a torque of 988 Nm at end B. The…
A:
Q: A torque T applied to a 1.2 m long and 50 mm diameter solid shaft increases until the shaft is fully…
A:
Q: Q3: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C).…
A:
Q: A flat key is to be designed for 100 mm diameter shaft which will transmit 200kw at 300 rpm . If the…
A: Given: τallow=300 MPaP=200kWN=300 rpmD=100 mmwkey=10 mm
Q: t (0) is 0.15°/
A: given:γmax=500×10-6 rad
Q: The shaft of a heavy-duty tractor transmits 120 kW at 600 rpm, and at the same time supports a load…
A:
Q: the shearing stress caused by a torque of 700 N m if dimension a =75 339. A tube 3 mm thick has the…
A:
Q: A shaft drives a gear set that is transmitting 5 hp at 1750 rpm. The diameter of the shaft is 0.75…
A:
Q: Steel shaft can be produced as solid body or circular tube with circular tube. The shaft must bear a…
A:
Q: Answer the following problem. Show your complete solution. Use 4 decimal places. Calculate the…
A: Given data: The power transmits, P = 45 kW. The speed of the shaft, N = 120 rpm. The permissible…
Q: A drilling riser is used to drill a 4km deep hole into the seabed. The riser can be approximated as…
A: Given. G= 89 Gpa , d_o = 185 mm d_i = 160 mm P= 230 Kw N= 75 rpm
A thin-walled tube having a semi circular shape has an outside diameter of 50 mm and a wall thickness of 2mm. If the stress concentration at the corners is neglected,What torque will cause a shearing stress of 40 MPa in N-m?
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 2 images
- A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
- When drilling a hole in a table leg, a furniture maker uses a hand-operated drill (see figure) with a bit of diameter d = 4.0 mm. If the resisting torque supplied by the table leg is equal to 0.3 N · m, what is the maximum shear stress in the drill bit? If the allowable shear stress in the drill bit is 32 MPa, what is the maximum resisting torque before the drill binds up? If the shear modulus of elasticity of the steel is G = 75 GPa, what is the rate of twist of the drill bit (degrees per meter)?A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
- A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
- Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to torques 7"at its ends. Calculate the maximum permissible torque 7jliajl if the allowable normal strain is ea= 5 X 10"4 Assume that G = 15 GPa.The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?