A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain yw at P. Assume a = 1350 mm, b = 850 mm, c = 1mm, and d = 1 mm.RAnswer: Shear strain yxyiprad.

Given data: a=1350 mmb=850 mmc=1 mmd=1 mm Need to determine the shear strain.

Answered: A thin rectangular plate is uniformly…

A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain yy at P. Assume a = 1350 mm, b = 850 mm, c= mm, and d = 1 mm. R Answer: Shear strain yy i Prad.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.2.5P: Solve the preceding problem if the length L = 56 in., the inner radius r1— 1.25 in., the angle of...

See similar textbooks

Related questions

Q: H.W.8 A thin triangular plate is uniformly deformed. Deter- mine the shear strain at P after point P…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given that: u = 2.3 mm, v = 3.9 mm c = 685 mm α =310, and β = 590 It is required to determine the…

Q: A thin rectangular polymer plate PQRS of width b = 360 mm and height a = 156 mm is shown in the…

Q: QUESTION 1: 1.1 A punch for making holes in steel plates of 8 mm thick, is shown in figure 1, has a…

Q: 124,000s o(2) 0 s85 0.03 (o in MPa) 1+ 300ɛ (a) Find the axial normal strain in the cable and its…

A: σε = 124,000 ε1 +300 ε 0≤ ε ≤ 0.03W = 6.8 kN To-Determine:- a. Axial normal strain in the cable and…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: 4) A metal plate has an area of face is 1m x 1 m and thickness of 1cm.One face of a larger area is…

A: (a) The Shear Stress is 4.2 x 108 N/m2. (b) The Shear Strain is 0.005. (c) The Shearing Force is 4.2…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Answer:-

Q: A thin polymer plate PQR is deformed such that corner Qis displaced downward 0.0625-in. to new…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: A high strength drill rod used for boring a hole in the earth has a diameter of 50 mm. The allowable…

Q: E, = 200.00 pE Eb = 400.00 pe E = 150.00 pe 600 The strain rosette shown was used to obtain normal…

Q: In a plane stress condition, the components of stress at point are ox = 20 MPa, ơy = 80 MPa and txy…

A: Given, Stress in x-direction = σx = 20 MPa Stress in y-direction = σy = 80 MPa Sheat stress in…

Q: Low Carbon structural steel has shearing ultimate strength of approximately 45,000 ib/in2 determine…

A: Given: The shearing strength of material = 45000 lb/in^2 The diameter of hole, d = 1 in The…

Q: M13.6 Principal stresses from rosette data scenes -200 µE 93 200 με b Ec = 500 µE 30° 30° Ex (με) a…

A: Given, εa = -200 x 10-6 εb = 200 x 10-6 εc = 500 x 10-6 E = 200 GPa ν = 0.32

Q: H.W. 3 The X- axis strains with oriented angle of the bone surface are shown in table X- axis strain…

A: The strain is given at different angles which are giving below – The strain at any angle can be…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: For the plate in figure 1 below, determine the exact solution for i. displacements u(x), v(y) ii.…

A: (i) Here, p is pressure applied on the plate. Now, write the displacements. u(x)=-pxE

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: A block of wood is tested in direct shear using the loading frame and test specimen shown in the…

A: Given data: load = 16 KN Need to determine the average shear stress.

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: A 60° strain rosette is glued to a girder. Under certain loading conditions at an instant, the…

A: Given data, εa = Strain at strain rosette a = 4.4x78 μ = 343.2μ εb = Strain at strain rosette b =…

Q: the nodal displacements are For the plane strain elements shown in the Figure given as (4, 4) uj =…

A: Solution: Given Data:

Q: In the figure shown, determine the normal stresses at AD • , shearing stress at + and BC bolt D • ,…

A: Solution: The free body diagram of the EDC is shown above, we need to find the reactions RD and RC…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given that: c = 790 mm, u = 1.3 mm, v = 5 mm The angles are α = 24o, and β = 66o It is required to…

Q: The principal plane stresses and associated strains in a plane at a point are s1 = 36 ksi, s2 = 16…

A: Given: The values of principal stresses are s1=36 ksi and s2=16 ksi. The values of strains are…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given data: u=1.4 mm v=5.1 mm c=680 mm α=21o β=69o

Q: Two blocks of wood, 50 mm wide and 20 mm thick, are glued together as shown in figure below. Using…

Q: Calculate non-zero stress components (normal and shear) at points A, B and C. Point C is located at…

A: Given: The length of the bar→L=100 mm=0.1 m Diameter of the bar→d=15 mm=0.015 m At point A: Because…

Q: A 60˚ strain rosette measures the following strain at a point on the aluminum skin ofan airplane. ϵ0…

A: Solution:

Q: subjected to a shearing force of 715N on its top cylindrical face. If the dowel has a diameter of…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given that: c = 720 mm u = 1.7 mm v = 3.5 mm α = 31o and β = 590 It is required to determine the…

Q: Figure 1. The boiler has an inside diameter of 1800 mm and a wall thickness of 20 mm, and it is made…

Q: The area of the upper face of a rectangular block is .5mx.5m The lower face is fixed. The height of…

Q: The plate shown in Figure is fixed connected along with AB and held in the horizontal guides at its…

A: When the plate is deformed then in that case the diagonal AC becomes AC'. Then from the pythagoreous…

Q: Determine the principle stresses and the maximum in-plane shear stress.

Q: A thin rectangular polymer plate PQRS of width b = 429 mm and height a = 140 mm is shown in the…

Q: A circular tube is subjected to torque Tat its ends. The resultingmaximum shear strain in the tube…

A: Given, Maximum shear strain,γmax=0.005Outer diameter,d2=3inInner diameter, d1=2.5inTo…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Please refer to the detailed solution given below, Answer - Shear strain is 4696.37 Micro-Radian

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: 3. A long thin walled cylindrical shell, closed at both the ends, is subjected to an internal…

A: Let us consider, Diameter of cylindrical shell = d Thickness of cylindrical shell = t Pressure…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: MECHANICS OF DEFORMABLE BODIES The butt joint shown in the figure is connected using five 20mm…

Q: A solid circular bar of steel (G = 78 GPa)transmits a torque T = 360 N ? m. The allowablestresses in…

Q: Find the minimum size of a hole that can be punched in a 20 mm thick mild steel plate having an…

A: Punching is a process is used to make holes in the sheet metal by forcing a tool which is called a…

Question

100%

A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain yw at P. Assume a = 1350 mm, b = 850 mm, c = 1
mm, and d = 1 mm.
R
Answer: Shear strain yxy
i
prad.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
The strains for an element of material in plane strain (see figure) are as follows: x = 480 ×10-6. y = 140 × l0-6, and xy = —350 x 10”. Determine the principals strains and maximum shear strains, and show these strains on sketches of properly oriented elements.
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
An clement of material subjected to plane strain (see figure) has strains of x=280106 , y=420106 , and xy=150106 . Calculate the strains for an element oriented at an angle = 35°. Show these strains on a sketch of a properly oriented element.
A strain rosette (see figure) mounted on the surface of an automobile frame gives the following readings: gage A,310 × 10-6:gage B,180 × l0-6; and gage C. -160 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?
Solve the preceding problem if the length L = 56 in., the inner radius r1— 1.25 in., the angle of twist is 0.5°, and the allowable shear strain is 0.0004 rad.
An aluminum tube has inside diameter dx= 50 mm, shear modulus of elasticity G = 27 GPa, v = 0.33, and torque T = 4.0 kN · m. The allowable shear stress in the aluminum is 50 MPa, and the allowable normal strain is 900 X 10-6. Determine the required outside diameter d2 Re-compute the required outside diameter d2, if allowable normal stress is 62 MPa and allowable shear strain is 1.7 X 10-3.
Assume that the normal strains x and y , for an clement in plane stress (see figure) are measured with strain gages. (a) Obtain a formula for the normal strain x in the : direction in terms x , y and Poisson’s ratio v. (b) Obtain a formula for the dilatation L’ in terms of x , y and Poisson’s ratio v.
Solve the preceding problem for the following strains: x=120106,y=450106,andxy=360106.
Solve Problem 7.7-9 by using Mohr’s circle for plane strain.