A straight tunnel is to run between two points A and B whose coordinates are as under. Point Northing 0.0 Easting 0.0 A B 3000 m 250 m A shaft is to be sunk at a point D which is at the middle of AB. As it is impossible to measure along AB directly, the point D is to be fixed from another point C whose coordinates are 1760 Im northing and 1395 m easting. Calculate (a) the coordinates of D, (b) the length and bearing of CD, and TH (c) the angle ACD, if the bearing of AC is 38°30' east of north.

A straight tunnel is to run between two points A and B whose coordinates are as under. Point Northing 0.0 Easting 0.0 A B 3000 m 250 m A shaft is to be sunk at a point D which is at the middle of AB. As it is impossible to measure along AB directly, the point D is to be fixed from another point C whose coordinates are 1760 Im northing and 1395 m easting. Calculate (a) the coordinates of D, (b) the length and bearing of CD, and TH (c) the angle ACD, if the bearing of AC is 38°30' east of north.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part C Compute the linear misclosure. Express your answer in feet to three significant figures. IΫΠ ΑΣΦ ↓↑ vec Submit Part D Compute the relative precision. Express your answer to three significant figures. 1: Request Answer 195| ΑΣΦ. 41 vec Submit Request Answer ? ? ft
Hi! Help me with this please. Thank you so much! A dumpy level is set up at one end of a line 160m. long for the purpose of determining the instrument stadia interval factor. The line is marked by hubs at every 40 m. and a stadia rod is held at each hub. The stadia intercept at each location of the rod were observed as follows: 0.402, 0.813, 1.231, 1.602 respectively. Compute the average value of the stadia interval factor. Height of instrument is 1.5m.
Q2: Given the following planar manipulator find the following a) °T2 b) ?R, c) The location of 02 relative to frame 0 suppose 0, = 30° 0, = 25° a1 = 1.5 az = 1
Q1). Calculate the volume of cut and fill from followings: bo = 6m, s = 10, n = 1 in cut, n = 2 in fill, assume left side higher than right side, the stations and elevations are taken along centerline." St. N.G. Elev. 87 88 1972 12+60 12+80 Design Elev. 82 94
Question 2. Below shown is the profile for a road construction at a station. This is a fill section. Sometimes the letter C is used to designate cut and F to indicate fill for the vertical distance or depth. In other words, a point below the base would have a negative sign in a fill section. F 11.8 below corresponds to -11.8 ft. The baseline is 50ft. Calculate the area for the fill section. (Answer: 137.3 yd²) 50ft F 11.8 -42.5 F 14.3 -32.0 0 -25 25 olo F 15.8 25 25 Baseline F 16.3 65.4
shouldnt R1=8.666 & R2=11.334??
Lines of levels between B and C are run over four different routes. B is at elevation 825 m and is higher than C. Route A Distance (km) Difference in Elevation (m) 0.86 0.69 0.75 1.02 6. C 4 8 a. Determine the weight of route B. b. Determine the most probable difference in elevation. c. Determine the most probable elevation of C.
Engineering surveying Assignment: Complete the following settlement table and verify that the calculations are correct. Then find the closing and adjust the levels of points. Suppose the error is equal for all device positions. Find the permissible length of the settlement line if the work is of the first degree. And thx.
375 1b/500 1b 4 6' 3 5' 0.5 0.5 3. Determine 30° 16016 moment about point B.
Determine the probable value of angle A, B, and C
Question 3 1 pts A field is in the form of a regular pentagon. The direction of the bounding sides was surveyed with the assumed meridian 6° to the right of the true north and south meridian., the bearing of one side AB is N 40°57' W. Compute the bearing of CD S 37°03' E O S 70°57' E O N 70°57' E O N 37°03' E
May you please include the whole process of the solution. Thank you! The marker is to be dragged out of the ground using two ropes A and B. Rope A is subjected to a force of 600lb and is directed at 60 Degree from the horizontal. If the resultant force acting on the post is to be 1200lb, vertically upward, determine the force T in rope B and the corresponding angle tetha.