A fully saturated soil sample has a diameter of 5cm and length of 10.2cm. the mass of the sample was 397g initially and after drying it reduced to 313g . specif gravity of soil is 2.7. find a) water content b)void ratio c) porosity

A fully saturated soil sample has a diameter of 5cm and length of 10.2cm. the mass of the sample was 397g initially and after drying it reduced to 313g . specif gravity of soil is 2.7. find a) water content b)void ratio c) porosity

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter3: Weight–volume Relationships

Section: Chapter Questions

Problem 3.10P

See similar textbooks

Related questions

Q: In a drainage system, closed drains are placed with their centres 1.8 m below the ground level. The…

A: For a given drainage system,Closed drains are placed with their centres 1.8 m below ground level.The…

Q: Consider the problem of traffic flow on a three-lane (one direction) freeway which can be described…

Q: A flat sheared connection plate 12" wide is to have 3-1" bolts vertically placed, answer the…

Q: Determine deflection at C (c) and deflection at D (do) for the beam below. E=1800 ksi, 1-46000 in

A: The given beam is shown below.

Q: The maximum slope of a ground for which the error due to slope is limited to 1 in 800 can be…

A: Error in slope =1 in 800 to find the maximum slope of a ground

Q: A 4.5 m high gravity retaining wall has to be designed to retain soil to increase the useable areas…

Q: 1. Volume of excavation for the foundation with depth 0.2 m 2. The amount of construction materials…

A: All the details of the plan and footing are given in question.We will use long-wall short-wall…

Q: A. Α M = 125 kip - in. y C ★ 2.4 in. 2.4 in. ↑ 2.4 in. 2.4 in. 2.4 in. 2.4 in.

Q: 2 #3 The rainfall was recorded at the network of stations over a trapezoidal watershed (see figure…

Q: A non-prismatic simply supported beam as shown in the figure is subjected to three point loading.…

A: For a non-prismatic simply supported beamTo find the maximum deflection for given condition of…

Q: a) The County requires you to renovate culvert designs for a peak flow representing a 100 years…

Q: Find the reactions at A,B and C using slope deflection method. Draw Shear and Moment diagrams.

A: The given beam is shown below.EI is consatnt.

Q: Q/For the slab shown in figure. fc' -30 MPa, fy-400MPa, WL. L-5 kN/m². Design floor slab of panel…

Q: What are some ways and materials contractors can use to improve noise levels in condos, office…

A: Acoustic Insulation: Installing sound-absorbing materials within walls, floors, and ceilings…

Q: A thin rectangular plate having the dimensions of a -20 mm and b-12 mm is acted upon by a stress…

A: A rectangular plate given asThe resulting strain Need to findChange in length in diagonal AC and QB

Q: Develop the global stiffness matrix [K] for the spring assemblage shown below using the…

A: The global stiffness matrix [K] for the spring assemblage shown can be developed as…

Q: Consider the given rectangular footing and soil having below mentioned properties: 1.5 m 1 m 7/8 D…

Q: The shear force diagram of a beam is shown in figure below. H D 2 m The bending moment at point 'E'…

A: For given shear force diagram,To find the bending moment at point E

Q: In a construction project, as in problem 1, effective cash needed before payment is received from…

A: In a construction project, as in problem 1, effective cash generated before payment is received from…

Q: Problem 4In water and wastewater treatment processes a filtration device may be used to remove water…

A: Given:Initial concentration of sludge (C1): 20,000 mg/LInitial volume of sludge (V1): 100 m³Final…

Q: A three hinged semi-circular arch of radius R carries a uniformly distributed load of w per unit run…

A: For a three hinged semi-circular arch of radius R carries a uniformly distributed load of w per unit…

Q: Answer question 3-9.Hint – Do not create a route which passes through the bridge (lower right side)…

A: In a solid waste collection process, truckrouting is an important aspect to minimizethe total…

Q: A solid cone of radius ro and vertex angle 20 is to rotate at an angular velocity w. The cone is…

Q: This is an answer you pulled from chegg, i was looking for something more detailed.

A: A parabolic crown follows a path of parabola while observed in cross section.Given,Level at center…

Q: In Fig. A, what is the height z if fluid A is water, fluid B is mercury, the gage pressure at m is…

A: Solution as follows.Explanation:

Q: been collected for those districts. Provide a trip distribution calculation (single constrained)…

A: Calculate the friction factor for each origin-destination pair by using the travel times and…

Q: Assuming the conduit in the figure is a 42” rough concrete pipe flowing full: a) Calculate the head…

A: a.) Head loss = 92.22 ft.b.) Velocity = 26.52 ft/sec ; Q = 255.15 ft^3/secc.) Velocity =…

Q: precipitation is 700mm of which 100mm is intercepted and evaporates ,100mmm runs off into stream .…

A: Precipitation: 700 mmInterception and evaporation: 100 mmRunoff: 100 mmInfiltration: 500…

Q: If the angle of obliquity for the resultant stress at a plane which is 45° from the principal stress…

A: To find the ratio of stress in x-direction to stress in y-direction

Q: a New York Building desires to reduce the normal completion time Job # 181 and, at the same time,…

A: Path A-B-C-F-G-H-I has a normal completion time of 20 weeks critical path A-D-E-F-G-H-11 completion…

Q: The rainfall was recorded at the network of stations over a trapezoidal watershed (see figure…

A: Rain fall recorded stations given in the figure belowStationprecipitation…

Q: The beam cross-section shown below has 90 kip-ft of bending moment applies to it. calculate the…

A: Maximum bending moment (M) = 90 kip-ft Determine the maximum compressive bending stress about…

Q: Write down the different stages (I to V) shown in the rate of heat evolution curve and briefly…

A: A rate of heat evolution curve is given in the figure belowNeed to find different stages of curve…

Q: How for the Cantilever in Fig Shown P 5m 80 쓱 beans find the reaction 3m 405 4000 111²2² 2m. 9+ 9001

Q: USE LRFD with 3 decimal places

A: The objective of the question is to calculate the spacing (pitch S) so that only two holes for 16mm…

Q: Q1/For a simple beam loaded as shown in Figure 1. Determine the slope and deflection at the position…

A: E = 2 × 105 N/mm2 I = 5 × 108 mm4 Determine the slope and deflection at midway of the beam. Let's…

Q: P + a + b

A: Force body diagram of given beam-Using method of consistent deformation (Force method) to analyze…

Q: Consider the simple pipe network below. Pipe AB and CF are both 500m long with diameters of 0.8m and…

A: LAB = LCF = 500 mL1 = 200 mL2 = 300 mQ = 3 m3/s

Q: Determine the support reactions of the following structure applying the principle of minimum strain…

Q: The bearing of a line AB in a closed traverse ABCA is 137°30' and its length is 125.8 m. The…

A: Bearing of line AB: 137°30′Length of line AB: 125.8 mX-coordinate of point A: -5 mY-coordinate of…

Q: The liquid limit of the soil sample is about 65% with corresponding volume of 42 cc. When the water…

A: Liquid limit of the soil sample: 65%Volume of soil sample at liquid limit: 42 ccWater content of dry…

Q: .

A: The dimensions of the HSS20x20x5/8 arewidth B= 20 inchesdepth H= 20 incheswall thickness t= 5/8…

Q: 1. Determine the design positive and negative moments of the beam shown. The dead and live loads are…

Q: 7. Determine the difference in pressure APAB between locations A and B in kilopascals (kPa) based on…

Q: Show your work please.

Q: Since the industrial revolution (~1750), humans have released over 1.5 trillion tons of CO2 into the…

Q: The water table in a deposit of uniform sand is located at 2 m below the ground level. Assuming the…

A: The water table in a deposit of uniform sand is located at 2 m below the ground level. The soil…

Q: D 7.0m. 2.0m Yt = 16.5 kN/m³ $' = 30° Loose sand fill: Yt = 19.5 kN/m3 $' = 30° Dense sand: Yt = 21…

A: The surcharge is equal to 10 KPa.Unit weight of water = 10 KN/m³for loose sand = 0.3 and for dense…

Q: A composite drive shaft is made up of two sections: a solid steel core and a brass tube encasing the…

A: A composite shaft made of brass and steel.The diameter of the steel part is 80 mm.The diameter of…

Q: using the same data can the axial and shear forces be calculated at B.

Question

A fully saturated soil sample has a diameter of 5cm and length of 10.2cm. the mass of the sample was 397g initially and after drying it reduced to 313g . specif gravity of soil is 2.7.

find

a) water content

b)void ratio

c) porosity

AI-Generated Solution

AI-generated content may present inaccurate or offensive content that does not represent bartleby’s views.

Unlock instant AI solutions

Tap the button
to generate a solution

Click the button to generate
a solution

SEE SOLUTION

Similar questions

A fully saturated soil sample has a diameter of 5cm and length of 10.2cm. the mass of the sample was 397g initially and after drying it reduced to 313g . specif gravity of soil is 2.7. find a) water content b)void ratio c) porosity d) Vs,Vw,Vv,V,Va
A soil sample has a unit weight of 1,825 kg/m^3.t weighs 1,730 kg/m 3 when dry. The unit weight of the soil particle is 2,600 kg/m*3. Determine the following: a.) Maisture content b.) Void ratio c.) degree of saturation
6. A soil sample of diameter 37.5 mm and length 75 mm has a wet weight of 1.32 and dry weight of 1.1 N. Determine the degree of saturation, porosity, bulk unit weight and dry unit weight.
An in-situ density test on a 542.5 cm^3 soil sample was conducted. The total weight of the sample at the site was 801.3 grams. Soil samples of the test were collected and moisture content was determined to be 4.5%. Assuming Gs = 2.71 determine:
Problem: Consider the following effects as indicative of complete saturation of a soil sample: 1. Pore water pressure is positive. 2. Volume of water to volume of voids is equal to 1. 3. Relative density is equal to 1. Which of the above statements are correct? (a) 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3
A soil sample has a density of 1,825 kg/m^3.t weighs 1,730 kg/m 3 when dry. The unit weight of the soil particle is 2,600 kg/m*3. Determine the following: a.) Maisture content b.) Void ratio c.) degree of saturation
1. From the following data of a soil sample: Sample size 3.81 cm dia. x 7.62 cm ht. Wet weight = 1.668 N Oven-dry weight = 1.400 N Specific gravity = 2.70 Detemine the water content (%), dry unit weight (kN/m3), bulk unit weight (kN/m3), void ratio, and the degree of saturation (%).
1) A soil deposit has a void ratio of 0.9. Its void ratio is reduced to 0.6 by compaction. Determine the percent reduction of volume by this compaction. 2)The mass of saturated soil sample is 150 gm and its mass when oven dried is 90 gm, find the water content. Suppose that the sample. Used for triaxial test, has a diameter of 38 mm and the height of 76 mm, find the void ratio.
during a subsurface exploration, an undiscovered soil sample was collected from the field using a split spoon sampler for lab evaluation. the sample has a diameter of 34.9mm length of 457.2mm and a moist mass of 840g. if the oven dried mass was 680g and Gs= 2.74 calculate the ff. a.)moist unit weight b.)moisture content c.)dry unit weight d.)void ratio e.)degree of saturation
ral condition a soil sample has a mass of 2290 g and a volume of 1.15x10*m. After being completely dried in an oyen the mass of the sample is 2035 g. The value of G. for the soil is 2.68. Determine: (1) Bulk density,
A sample of clay taken from a natural stratum was found to be partially saturated and when tested in the laboratory gave the following results. Compute the degree of saturation. Specific gravity of soil particles = 2.6; wet weight of sample = 2.50 N; dry weight of sample = 2.10 N; and volume of sample = 150 cm3.
A fully saturated soil sample has a volume of 28 cc. The sample was dried in oven and the weight of the dry soil pat was found to be 48.76 g. Given G= 2.68. Determine the porosity in percent.