A steel wire of length 2.08 m with circular cross section must stretch no more than 0.300 cm when a tensile (stretching) force of 390 N is applied to each end of the wire. Part A What minimum diameter dmin is required for the wire? Express your answer in millimeters. Take Young's modulus for steel to be Y = 2.00x1011 Pa. • View Available Hint(s) dmin = mm

A steel wire of length 2.08 m with circular cross section must stretch no more than 0.300 cm when a tensile (stretching) force of 390 N is applied to each end of the wire. Part A What minimum diameter dmin is required for the wire? Express your answer in millimeters. Take Young's modulus for steel to be Y = 2.00x1011 Pa. • View Available Hint(s) dmin = mm

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 60P: A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a...

See similar textbooks

Similar questions

A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?
What Is Static Equilibrium? Problems 13 are grouped. 1. C A ball is attached to a strong, lightweight rod (Fig. P14.1). The rod is supported by a horizontal pin near the top. The ball is at rest. Is the ball in static equilibrium? If not, why not? If so, which type of equilibrium is itstable, unstable, or neutral? Hint: What would happen if you displaced the ball slightly? FIGURE P14.1
A brass wire and a steel wire, both of the same length, are extended by 1.0 mm under the same force. Is the cross-sectional radius of the brass wire more, less, or equal to the cross-sectional radius of the steel wire? Explain. Youngs moduli for brass and steel are 1.0 1010 N/m2 and 2.0 1011 N/m2, respectively.
A steel cable 2.00 m in length and with cross-sectional radius 0.350 mm is used to suspend from the ceiling a 10.0-kg model aircraft that is flying in a horizontal circle with an angular speed of 6.00 rad/s. What is the strain produced in the cable?
Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial diamond of volume 1.00 106 m3 is formed under a pressure of 5.00 GPa. Find the change in its volume when it is released from the press and brought to atmospheric pressure. Take the diamonds bulk modulus to be B = 194 GPa.
By how much does a 65.0kg mountain climber stretch her 0.800cm diameter nylon rope when she hangs 35.0m below a rock outcropping? (For nylon, Y=1.35109Pa. )
A HOMEWRK-1: The average cross-sectional area of leg 3 cm² and all of body weight 700 N supported of this leg, and the amount of shorting (AL) = 0.15 mm find the length of this leg in meter if you know that young's modulus of the bone is 1.8 * 10¹0 N/m². ANSWER L = 1.157 m L? A--3X1=4 F-100 16 4 - 1881-
A circular rod of cross-sectional area 2 x 104 m² has a tensile force of 80 kN applied to it. The stress in the rod is Select one: a. 4.0 x 106 Pa b. 0.4 x 10° Pa O c. 40 x 104 Pa Previous page Formula Sheet, CA-2, T-3, AY Jump to... Activate Windo 20-21 Go to Settings to act hp
The beam is supported by a pin at A and a short link BC. Figure 1 of 1 > 0.5 m Tadika 1m 1.5 m 1.5 m H. Part A If P = 13 kN, determine the average shear stress developed in the pins at A, B, and C. All pins are in double shear as shown, and each has a diameter of 17 mm. (Figure 1) Enter your answers separated by commas. TA. TB. TC = Submit Provide Feedback 197| ΑΣΦ | 11 | vec Request Answer MPa I