Compute the maximum bending moment, maxi- mum deflection and the maximum bending stress for a railroad rail subjected to a single wheel load of 100 kN. The foundation modulus k = 15 MN/m². Assume that I = 400 × 10-8 m4, E = 200 GN/m2, the depth of the rail is 180 mm and that the distance of the centroidal axis of the cross-section of the rail from the top surface is 100 mm. X

Compute the maximum bending moment, maxi- mum deflection and the maximum bending stress for a railroad rail subjected to a single wheel load of 100 kN. The foundation modulus k = 15 MN/m². Assume that I = 400 × 10-8 m4, E = 200 GN/m2, the depth of the rail is 180 mm and that the distance of the centroidal axis of the cross-section of the rail from the top surface is 100 mm. X

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. 2. 10 mm 10 mm 3. 5 mm 100 mm A beam section as shown in the sketch is subjected to a bendingmoment of Mx = 4 kN.m and a shear force of V = 2.5KN. 50 mm 100 mm Calculate the position of the centroid and the the second moment of area of the section about the sentroid horizontally. Draw the bending stress distribution through the height of the beam by calculating the bending stress at the critical positions Draw the shear stress distribution trough the height of the beam by calculating the shear stress below the flanges and at the centroid. 4. Draw the stress condition below the flanges, at the centroid and at the top and bottom of the beam.(7) 5. Draw the shearflow through the section. Show calculations
A long concrete footing rests on an earth founda- tion for which the value of the foundation modulus is 5-6 MN/m2. The footing has a cross-section 200 mm wide and 200 mm deep. The footing supports a uniformly distributed load of 2 kN/m of length which ex- tends over a 3 m length. Compute the value of the maximum bending moment in the footing and the maximum bending stress. E = 14 GN/m2.
The cross-sectional dimensions of the beam are a = 4.8 in, b = 6.5 in, d=4.5 in, and t= 0.30 in. The internal bending moment about the z centroidal axis is Mz= -3.90 kip-ft. Answers both in psi
Determine the internal normal force and shear force, and the bending moment in the beam at points C and D. Assume the support at B is a roller. Point C is located just to the right of the 8-kip load. For your explanation section, complete a FBD of the other side of the beam from the version you did to solve the problem. 8 kip 40 kip · ft A to to D B- 8 ft 8 ft- -8 ft
If the I-flange beam is subjected to a shear force V = 20 kN, calculate the transverse shear stress at the point A (considered located on the web part). The area moment of inertia of that section about its neutral axis N.A. is INA = 44.167 x (106) m4. Flange Web Select one: O 41 MPa 10 Mpa O 4.95 MPa O O 50 MPa 100 MPa 20 mm 100 mm A 100 mm 25 mm 150 mm 25 mm
The internal loadings at a cross section through the 120-mm-diameter drive shaft of a turbine consist of an axial force of 12.5 kN, a bending moment of 1.2 kN - m, and a torsional moment of 2.25 kN m. (Eigure 1). Figure 1.2 kN-m 12.5 kN 1 of 1 2.25 kN-m
of on If the I-flange beam is subjected to a shear force V= 20 kN, calculate the transverse shear stress at the point A (considered located on the web part). The area moment of inertia of that section about its neutral axis N.A. is INA = 44.167 x (10) m². Flange Web. Select one: O 10 Mpa O 4.95 MPa O 41 MPa O 100 MPa O50 MPa 20 mm 100 mm A 100 mm 25 mm 150 mm 25 mm Time left 0:46:01 s
If Mz = 200 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross section, assume a = 7 in. b = 10 in. d = 26 in. r = 3.5 in. The centroid of the cross section is located 11.96 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 12903 in.4.
The bending moment M is applied to the box beam in the x-y plane at the orientation show below. (a) Determine the maximum magnitude of the bending moment M so that the tensile bending stress in the member does not exceed 15 ksi. (b) Determine the angle that the neutral axis makes with the y-axis. (c) The position or positions on the beam where the maximum compressive bending stress occurs given your answer in a. Clearly indicate this on the figure below (also calculate the values) 4 in. B 4 in. M 6 in. 6 in.
Consider an 8-m long simply supported T-beam with overhangs loaded as shown below. 200 mm w kN/m 50 mm 50 kN-m 50 kN-m 200 mm 2 m 4 m 2 m 50 mm 1. Determine the location of the neutral axis measured from the top of the beam and the moment of inertia (in mm4) of the section about its neutral axis. Draw the shear and bending moment diagrams. Annotate all relevant values and distances. Determine the magnitude of the maximum negative 2. moment. Determine the minimum allowable strength of the beam in tension and the minimum allowable strength of the beam in compression. 3. Determine the maximum allowable load, w (in kN/m), that can be applied pn the beam. 4. B.
The lever must exert a force of P = 3800 Ibs at B as shown. The lever lengths are a = 11 in. and b = 47 in. The allowable bending stress for the lever is 12600 psi. If the lever height h is to be 3.5 times the lever thickness t (i.e., h/t = 3.5), what is the minimum thickness t that can be used for the lever? h Cross section Lever a Answer: t = i in.
A leaf spring 75 cm long is required to carry a central load of 8 kN. If the central deflection is not to exceed 2 cm and bending stress no greater than 200 MPa, determine the thickness, width and number of plates. Also compute the radius to which plates should be curved. As- sume width of plate to be 12 times its thickness and E = 200 GPa.